[PATCH tty v1 35/74] serial: mcf: Use port lock wrappers

[John Ogness]

From: Thomas Gleixner <tglx@xxxxxxxxxxxxx>

When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.

So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.

All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.

To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.

Converted with coccinelle. No functional change.

Signed-off-by: Thomas Gleixner <tglx@xxxxxxxxxxxxx>
---
 drivers/tty/serial/mcf.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
index 1666ce012e5e..91b15243f6c6 100644
--- a/drivers/tty/serial/mcf.c
+++ b/drivers/tty/serial/mcf.c
@@ -135,12 +135,12 @@ static void mcf_break_ctl(struct uart_port *port, int break_state)
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 	if (break_state == -1)
 		writeb(MCFUART_UCR_CMDBREAKSTART, port->membase + MCFUART_UCR);
 	else
 		writeb(MCFUART_UCR_CMDBREAKSTOP, port->membase + MCFUART_UCR);
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 /****************************************************************************/
@@ -150,7 +150,7 @@ static int mcf_startup(struct uart_port *port)
 	struct mcf_uart *pp = container_of(port, struct mcf_uart, port);
 	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 
 	/* Reset UART, get it into known state... */
 	writeb(MCFUART_UCR_CMDRESETRX, port->membase + MCFUART_UCR);
@@ -164,7 +164,7 @@ static int mcf_startup(struct uart_port *port)
 	pp->imr = MCFUART_UIR_RXREADY;
 	writeb(pp->imr, port->membase + MCFUART_UIMR);
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 
 	return 0;
 }
@@ -176,7 +176,7 @@ static void mcf_shutdown(struct uart_port *port)
 	struct mcf_uart *pp = container_of(port, struct mcf_uart, port);
 	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 
 	/* Disable all interrupts now */
 	pp->imr = 0;
@@ -186,7 +186,7 @@ static void mcf_shutdown(struct uart_port *port)
 	writeb(MCFUART_UCR_CMDRESETRX, port->membase + MCFUART_UCR);
 	writeb(MCFUART_UCR_CMDRESETTX, port->membase + MCFUART_UCR);
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 /****************************************************************************/
@@ -252,7 +252,7 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
 		mr2 |= MCFUART_MR2_TXCTS;
 	}
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 	if (port->rs485.flags & SER_RS485_ENABLED) {
 		dev_dbg(port->dev, "Setting UART to RS485\n");
 		mr2 |= MCFUART_MR2_TXRTS;
@@ -273,7 +273,7 @@ static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
 		port->membase + MCFUART_UCSR);
 	writeb(MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE,
 		port->membase + MCFUART_UCR);
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 /****************************************************************************/
@@ -350,7 +350,7 @@ static irqreturn_t mcf_interrupt(int irq, void *data)
 
 	isr = readb(port->membase + MCFUART_UISR) & pp->imr;
 
-	spin_lock(&port->lock);
+	uart_port_lock(port);
 	if (isr & MCFUART_UIR_RXREADY) {
 		mcf_rx_chars(pp);
 		ret = IRQ_HANDLED;
@@ -359,7 +359,7 @@ static irqreturn_t mcf_interrupt(int irq, void *data)
 		mcf_tx_chars(pp);
 		ret = IRQ_HANDLED;
 	}
-	spin_unlock(&port->lock);
+	uart_port_unlock(port);
 
 	return ret;
 }
-- 
2.39.2