Re: [PATCH v2 1/2] usb: typec: tps6598x: add reset gpio support

[Heikki Krogerus]

On Fri, Sep 15, 2023 at 02:23:48PM +0200, Javier Carrasco wrote:
> The TPS6598x PD controller provides an active-high hardware reset input
> that reinitializes all device settings. If it is not grounded by
> design, the driver must be able to de-assert it in order to initialize
> the device.
> 
> The PD controller is not ready for registration right after the reset
> de-assertion and a delay must be introduced in that case. According to
> TI, the delay can reach up to 1000 ms [1], which is in line with the
> experimental results obtained with a TPS65987D.
> 
> Add a GPIO descriptor for the reset signal and basic reset management
> for initialization and suspend/resume.
> 
> [1] https://e2e.ti.com/support/power-management-group/power-management/
> f/power-management-forum/1269856/tps65987d-tps65987d-reset-de-assert-
> to-normal-operation/4809389#4809389
> 
> Signed-off-by: Javier Carrasco <javier.carrasco@xxxxxxxxxxxxxx>
> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
> ---
>  drivers/usb/typec/tipd/core.c | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/drivers/usb/typec/tipd/core.c b/drivers/usb/typec/tipd/core.c
> index 37b56ce75f39..3068ef300073 100644
> --- a/drivers/usb/typec/tipd/core.c
> +++ b/drivers/usb/typec/tipd/core.c
> @@ -8,6 +8,7 @@
>  
>  #include <linux/i2c.h>
>  #include <linux/acpi.h>
> +#include <linux/gpio/consumer.h>
>  #include <linux/module.h>
>  #include <linux/of.h>
>  #include <linux/power_supply.h>
> @@ -43,6 +44,9 @@
>  /* TPS_REG_SYSTEM_CONF bits */
>  #define TPS_SYSCONF_PORTINFO(c)		((c) & 7)
>  
> +/* reset de-assertion to ready for operation */
> +#define SETUP_MS			1000
> +
>  enum {
>  	TPS_PORTINFO_SINK,
>  	TPS_PORTINFO_SINK_ACCESSORY,
> @@ -86,6 +90,7 @@ struct tps6598x {
>  	struct mutex lock; /* device lock */
>  	u8 i2c_protocol:1;
>  
> +	struct gpio_desc *reset;
>  	struct typec_port *port;
>  	struct typec_partner *partner;
>  	struct usb_pd_identity partner_identity;
> @@ -717,6 +722,13 @@ static int tps6598x_probe(struct i2c_client *client)
>  	mutex_init(&tps->lock);
>  	tps->dev = &client->dev;
>  
> +	tps->reset = devm_gpiod_get_optional(tps->dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(tps->reset))
> +		return dev_err_probe(tps->dev, PTR_ERR(tps->reset),
> +				     "failed to get reset GPIO\n");
> +	if (tps->reset)
> +		msleep(SETUP_MS);
> +
>  	tps->regmap = devm_regmap_init_i2c(client, &tps6598x_regmap_config);
>  	if (IS_ERR(tps->regmap))
>  		return PTR_ERR(tps->regmap);
> @@ -892,6 +904,9 @@ static void tps6598x_remove(struct i2c_client *client)
>  	tps6598x_disconnect(tps, 0);
>  	typec_unregister_port(tps->port);
>  	usb_role_switch_put(tps->role_sw);
> +
> +	if (tps->reset)
> +		gpiod_set_value_cansleep(tps->reset, 1);

Do you need that "if (tps->reset)" in this case? That function is NULL safe,
right?

>  }
>  
>  static int __maybe_unused tps6598x_suspend(struct device *dev)
> @@ -902,6 +917,8 @@ static int __maybe_unused tps6598x_suspend(struct device *dev)
>  	if (tps->wakeup) {
>  		disable_irq(client->irq);
>  		enable_irq_wake(client->irq);
> +	} else if (tps->reset) {
> +		gpiod_set_value_cansleep(tps->reset, 1);
>  	}
>  
>  	if (!client->irq)
> @@ -918,6 +935,9 @@ static int __maybe_unused tps6598x_resume(struct device *dev)
>  	if (tps->wakeup) {
>  		disable_irq_wake(client->irq);
>  		enable_irq(client->irq);
> +	} else if (tps->reset) {
> +		gpiod_set_value_cansleep(tps->reset, 0);
> +		msleep(SETUP_MS);
>  	}
>  
>  	if (!client->irq)
> 
> -- 
> 2.39.2

thanks,

-- 
heikki