[PATCH v2 02/19] staging: iio: Documentation: document IIO resolver AD2S1210 sysfs attributes

[David Lechner]

This adds documentation for the device-specific sysfs attributes of the
iio/resolver/ad2s1210 driver.

Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
---
 .../sysfs-bus-iio-resolver-ad2s1210           | 109 ++++++++++++++++++
 1 file changed, 109 insertions(+)
 create mode 100644 drivers/staging/iio/Documentation/sysfs-bus-iio-resolver-ad2s1210

diff --git a/drivers/staging/iio/Documentation/sysfs-bus-iio-resolver-ad2s1210 b/drivers/staging/iio/Documentation/sysfs-bus-iio-resolver-ad2s1210
new file mode 100644
index 000000000000..32890c85168e
--- /dev/null
+++ b/drivers/staging/iio/Documentation/sysfs-bus-iio-resolver-ad2s1210
@@ -0,0 +1,109 @@
+What:		/sys/bus/iio/devices/iio:deviceX/dos_mis_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Degradation of Signal Mismatch
+		Threshold value. Writing sets the value. Valid values are 0 (0V)
+		to 127 (4.826V). To convert the value to volts, multiply by
+		0.038.
+
+What:		/sys/bus/iio/devices/iio:deviceX/dos_ovr_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Degradation of Signal Overrange
+		Threshold value. Writing sets the value. Valid values are 0 (0V)
+		to 127 (4.826V). To convert the value to volts, multiply by
+		0.038.
+
+What:		/sys/bus/iio/devices/iio:deviceX/dos_rst_max_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Degradation of Signal Reset Maximum
+		Threshold value. Writing sets the value. Valid values are 0 (0V)
+		to 127 (4.826V). To convert the value to volts, multiply by
+		0.038.
+
+What:		/sys/bus/iio/devices/iio:deviceX/dos_rst_min_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Degradation of Signal Reset Minimum
+		Threshold value. Writing sets the value. Valid values are 0 (0V)
+		to 127 (4.826V). To convert the value to volts, multiply by
+		0.038.
+
+What:		/sys/bus/iio/devices/iio:deviceX/fault
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns a hex value containing the fault bit flags.
+
+		Bit	Description
+		---	-----------
+		D7	Sine/cosine inputs clipped
+		D6	Sine/cosine inputs below LOS threshold
+		D5	Sine/cosine inputs exceed DOS overrange threshold
+		D4	Sine/cosine inputs exceed DOS mismatch threshold
+		D3	Tracking error exceeds LOT threshold
+		D2	Velocity exceeds maximum tracking rate
+		D1	Phase error exceeds phase lock range
+		D0	Configuration parity error
+
+		Writing any value will clear any fault conditions.
+
+What:		/sys/bus/iio/devices/iio:deviceX/excitation_frequency
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Excitation Frequency in Hz. Writing
+		sets the Excitation Frequency and performs a software reset on
+		the device to apply the change. Valid values are 2000 (2kHz) to
+		20000 (20kHz).
+
+What:		/sys/bus/iio/devices/iio:deviceX/los_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Loss of Signal Reset Threshold
+		value. Writing sets the value. Valid values are 0 (0V) to
+		127 (4.826V). To convert the value to volts, multiply by 0.038.
+
+What:		/sys/bus/iio/devices/iio:deviceX/lot_high_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Loss of Position Tracking Detection
+		High Threshold value. Writing sets the value. Valid values are
+		0 (0 deg) to 127 (9/18/45 deg). The interpretation of the value
+		depends on the selected resolution. To convert the value to
+		degrees, multiply by 0.35 for 10-bit resolution, multiply by
+		0.14 for 12-bit resolution or multiply by 0.09 for 14 and 16-bit
+		resolution.
+
+What:		/sys/bus/iio/devices/iio:deviceX/lot_low_thrd
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Loss of Position Tracking Detection
+		Low Threshold value. Writing sets the value. Valid values are
+		0 (0 deg) to 127 (9/18/45 deg). The interpretation of the value
+		depends on the selected resolution. To convert the value to
+		degrees, multiply by 0.35 for 10-bit resolution, multiply by
+		0.14 for 12-bit resolution or multiply by 0.09 for 14 and 16-bit
+		resolution.
+
+What:		/sys/bus/iio/devices/iio:deviceX/phase_lock_range
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the current Phase lock range in degrees. Writing
+		sets the value in the configuration register.
+
+What:		/sys/bus/iio/devices/iio:deviceX/phase_lock_range_available
+KernelVersion:  6.7
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Reading returns the possible values for the phase_lock_range
+		attribute, namely 44 and 360.
-- 
2.34.1