Re: [PATCH 3/3] i2c: mv64xxx: add support for FSM based recovery

[Chris Packham]

On 6/10/23 10:58, Andi Shyti wrote:
> Hi Chris,
>
> Looks good, just a few questions.
>
>> +static int
>> +mv64xxx_i2c_recover_bus(struct i2c_adapter *adap)
>> +{
>> +	struct mv64xxx_i2c_data *drv_data = i2c_get_adapdata(adap);
>> +	int ret;
>> +	u32 val;
>> +
>> +	dev_dbg(&adap->dev, "Trying i2c bus recovery\n");
>> +	writel(MV64XXX_I2C_UNSTUCK_TRIGGER, drv_data->unstuck_reg);
>> +	ret = readl_poll_timeout_atomic(drv_data->unstuck_reg, val,
>> +					!(val & MV64XXX_I2C_UNSTUCK_INPROGRESS),
>> +					1000, 5000);
> here you are busy looping for 1ms between reads which is a long
> time. Why not using read_poll_timeout() instead?

I needed to use the atomic variant because this ends up getting called 
from an interrupt handler (mv64xxx_i2c_intr() -> mv64xxx_i2c_fsm()). I 
probably don't need to wait so long between reads those times were just 
pulled out of thin air. In my experimentation the faults that can be 
cleared do so within a couple of clocks, if it hasn't cleared within 8 
clocks it's not going to.

>> +	if (ret) {
>> +		dev_err(&adap->dev, "recovery timeout\n");
>> +		return ret;
>> +	}
>> +
>> +	if (val & MV64XXX_I2C_UNSTUCK_ERROR) {
>> +		dev_err(&adap->dev, "recovery failed\n");
>> +		return -EBUSY;
>> +	}
>> +
>> +	dev_info(&adap->dev, "recovery complete after %d pulses\n", MV64XXX_I2C_UNSTUCK_COUNT(val));
> dev_dbg?
ack.
>> +	return 0;
>> +}
>> +
> [...]
>
>> -	if (of_device_is_compatible(np, "marvell,mv78230-a0-i2c")) {
>> +	if (of_device_is_compatible(np, "marvell,mv78230-a0-i2c") ||
>> +	    of_device_is_compatible(np, "marvell,armada-8k-i2c")) {
> should this be part of a different patch?

Yes sorry. Originally I was going to use a new compatible to indicate 
the unstuck support but went with the 2nd reg cell so this is unnecessary.

>
>>   		drv_data->offload_enabled = false;
>>   		/* The delay is only needed in standard mode (100kHz) */
>>   		if (bus_freq <= I2C_MAX_STANDARD_MODE_FREQ)
>> @@ -936,8 +973,21 @@ mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data,
>>   }
>>   #endif /* CONFIG_OF */
>>   
>> -static int mv64xxx_i2c_init_recovery_info(struct mv64xxx_i2c_data *drv_data,
>> -					  struct device *dev)
>> +static int mv64xxx_i2c_init_fsm_recovery_info(struct mv64xxx_i2c_data *drv_data,
>> +					      struct device *dev)
>> +{
>> +	struct i2c_bus_recovery_info *rinfo = &drv_data->rinfo;
>> +
>> +	dev_info(dev, "using FSM for recovery\n");
> dev_dbg?
>
>> +	rinfo->recover_bus = mv64xxx_i2c_recover_bus;
>> +	drv_data->adapter.bus_recovery_info = rinfo;
>> +
>> +	return 0;
>> +
>> +}
>> +
> [...]
>
>> +	/* optional unstuck support */
>> +	res = platform_get_resource(pd, IORESOURCE_MEM, 1);
>> +	if (res) {
>> +		drv_data->unstuck_reg = devm_ioremap_resource(&pd->dev, res);
>> +		if (IS_ERR(drv_data->unstuck_reg))
>> +			return PTR_ERR(drv_data->unstuck_reg);
> OK, we failed to ioremap... but instead of returning an error,
> wouldn't it be better to just set unstuck_reg to NULL and move
> forward without unstuck support?
>
> Maybe you will stil crash later because something might have
> happened, but failing on purpose on an optional feature looks a
> bit too drastic to me. What do you think?

Personally I think if the reg property is supplied in the dts we'd 
better be able to use it. If the feature is not wanted then the way to 
indicate this is by supplying only one reg cell.

I'd be happy with a dev_warn() and unstuck_reg = NULL if that helps get 
this landed.

>
> Thanks,
> Andi