Re: [PATCH] iio: bu27008: Add processed illuminance channel
From: Matti Vaittinen
Date: Fri Oct 06 2023 - 01:01:25 EST
On 10/5/23 18:14, Jonathan Cameron wrote:
On Mon, 2 Oct 2023 15:33:41 +0300
Matti Vaittinen <mazziesaccount@xxxxxxxxx> wrote:
The RGB + IR data can be used to calculate illuminance value (Luxes).
Implement the equation obtained from the ROHM HW colleagues and add a
light data channel outputting illuminance values in (nano) Luxes.
Units in the ABI doc for illuminance are Lux, not nanolux.
I'm guessing that you actually provide it in Lux but via scale.
Make that clearer in this description if so.
Yep. Also, the "processed" is misleading as I implement a raw channel. I
did originally think I'll only implement the read_raw (as I thought
we'll need all RGBC + IR and end up doing two accesses - which wouldn't
be nice due to the doubled measurement time). I actually did that and
used INT_PLUS_NANO. While implementing this I noticed the 'clear' data
was not used - and thought I might as well support buffering when RGB+IR
are enabled. I needed the scale to get the buffered values to decent
format though - so I converted channel to raw one and added scale. The
commit title still contains the 'processed' which reflects the original
thinking. Thanks for pointing out the confusion.
Both the read_raw and buffering values is supported, with the limitation
that buffering is only allowed when suitable scan-mask is used. (RGB+IR,
no clear).
The equation has been developed by ROHM HW colleagues for open air sensor.
Adding any lens to the sensor is likely to impact to the used c1, c2, c3
coefficients. Also, The output values have only been tested on BU27008.
According to the HW colleagues, the very same equation should work also
on BU27010.
Calculate and output illuminance values from BU27008 and BU27010.
Signed-off-by: Matti Vaittinen <mazziesaccount@xxxxxxxxx>
A few comments inline, but in general looks fine to me.
Thanks Jonathan. I had to give also the BU27008 sensor away for a while.
I guess I won't send the next version until I am able to do some very
basic testing even if the changes were minor. That's probably sometime
next week.
Jonathan
---
I did very dummy testing at very normal daylight inside a building. No
special equipments were used - I simply compared values computed from
BU27008 RGB+IR channels, to values displayed by the ALS in my mobile
phone. Results were roughly the same (around 400 lux). Couldn't repeat
test on BU27010, but the data it outputs should be same format as
BU27008 data so equation should work for both sensors.
---
drivers/iio/light/rohm-bu27008.c | 216 ++++++++++++++++++++++++++++++-
1 file changed, 211 insertions(+), 5 deletions(-)
diff --git a/drivers/iio/light/rohm-bu27008.c b/drivers/iio/light/rohm-bu27008.c
index 6a6d77805091..d480cf761377 100644
--- a/drivers/iio/light/rohm-bu27008.c
+++ b/drivers/iio/light/rohm-bu27008.c
@@ -130,6 +130,7 @@
* @BU27008_BLUE: Blue channel. Via data2 (when used).
* @BU27008_CLEAR: Clear channel. Via data2 or data3 (when used).
* @BU27008_IR: IR channel. Via data3 (when used).
+ * @BU27008_LUX: Illuminance channel, computed using RGB and IR.
* @BU27008_NUM_CHANS: Number of channel types.
*/
enum bu27008_chan_type {
@@ -138,6 +139,7 @@ enum bu27008_chan_type {
BU27008_BLUE,
BU27008_CLEAR,
BU27008_IR,
+ BU27008_LUX,
BU27008_NUM_CHANS
};
@@ -172,6 +174,8 @@ static const unsigned long bu27008_scan_masks[] = {
ALWAYS_SCANNABLE | BIT(BU27008_CLEAR) | BIT(BU27008_IR),
/* buffer is R, G, B, IR */
ALWAYS_SCANNABLE | BIT(BU27008_BLUE) | BIT(BU27008_IR),
+ /* buffer is R, G, B, IR, LUX */
+ ALWAYS_SCANNABLE | BIT(BU27008_BLUE) | BIT(BU27008_IR) | BIT(BU27008_LUX),
0
};
@@ -331,6 +335,19 @@ static const struct iio_chan_spec bu27008_channels[] = {
* Hence we don't advertise available ones either.
*/
BU27008_CHAN(IR, DATA3, 0),
+ {
+ .type = IIO_LIGHT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ .channel = BU27008_LUX,
+ .scan_index = BU27008_LUX,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 64,
+ .storagebits = 64,
+ .endianness = IIO_CPU,
+ },
+ },
IIO_CHAN_SOFT_TIMESTAMP(BU27008_NUM_CHANS),
};
@@ -1004,6 +1021,183 @@ static int bu27008_read_one(struct bu27008_data *data, struct iio_dev *idev,
return ret;
}
+static int bu27008_get_rgb_ir(struct bu27008_data *data, unsigned int *red,
+ unsigned int *green, unsigned int *blue, unsigned int *ir)
+{
+ int ret, chan_sel, int_time, tmpret, valid;
+ __le16 chans[BU27008_NUM_HW_CHANS];
+
+ chan_sel = BU27008_BLUE2_IR3 << (ffs(data->cd->chan_sel_mask) - 1);
+
+ ret = regmap_update_bits(data->regmap, data->cd->chan_sel_reg,
+ data->cd->chan_sel_mask, chan_sel);
+ if (ret)
+ return ret;
+
+ ret = bu27008_meas_set(data, true);
+ if (ret)
+ return ret;
+
+ ret = bu27008_get_int_time_us(data);
+ if (ret < 0)
+ int_time = BU27008_MEAS_TIME_MAX_MS;
+ else
+ int_time = ret / USEC_PER_MSEC;
+
+ msleep(int_time);
+
+ ret = regmap_read_poll_timeout(data->regmap, data->cd->valid_reg,
+ valid, (valid & BU27008_MASK_VALID),
+ BU27008_VALID_RESULT_WAIT_QUANTA_US,
+ BU27008_MAX_VALID_RESULT_WAIT_US);
+ if (ret)
+ goto out;
+
+ ret = regmap_bulk_read(data->regmap, BU27008_REG_DATA0_LO, chans,
+ sizeof(chans));
+ if (ret)
+ goto out;
+
+ *red = le16_to_cpu(chans[0]);
+ *green = le16_to_cpu(chans[1]);
+ *blue = le16_to_cpu(chans[2]);
+ *ir = le16_to_cpu(chans[3]);
I'd be tempted to use an array + definitely pass them as u16 rather
than unsigned int.
I'm not really convinced the u16 is better here. We need the 32 bits
later for the calculations - and (afaics) using natural size int for
arguments shouldn't harm. We read the channel data to correct type array
so code should be pretty clear as to what we have in HW.
Also, I think that having an array obfuscates what element is which
channel because these ICs didn't have the 1 to 1 mapping from channel
index to colour. I was thinking of adding a struct for this but decided
to just keep it simple and clear.
+
+out:
+ tmpret = bu27008_meas_set(data, false);
+ if (tmpret)
+ dev_warn(data->dev, "Stopping measurement failed\n");
+
+ return ret;
+}
+
+/*
+ * Following equation for computing lux out of register values was given by
+ * ROHM HW colleagues;
+ *
+ * Red = RedData*1024 / Gain * 20 / meas_mode
+ * Green = GreenData* 1024 / Gain * 20 / meas_mode
+ * Blue = BlueData* 1024 / Gain * 20 / meas_mode
+ * IR = IrData* 1024 / Gain * 20 / meas_mode
+ *
+ * where meas_mode is the integration time in mS / 10
+ *
+ * IRratio = (IR > 0.18 * Green) ? 0 : 1
+ *
+ * Lx = max(c1*Red + c2*Green + c3*Blue,0)
+ *
+ * for
+ * IRratio 0: c1 = -0.00002237, c2 = 0.0003219, c3 = -0.000120371
+ * IRratio 1: c1 = -0.00001074, c2 = 0.000305415, c3 = -0.000129367
+ */
+
+/*
+ * The max chan data is 0xffff. When we multiply it by 1024 * 20, we'll get
+ * 0x4FFFB000 which still fits in 32-bit integer. So this can't overflow.
+ */
+#define NORM_CHAN_DATA_FOR_LX_CALC(chan, gain, time) ((chan) * 1024 * 20 / \
+ (gain) / (time))
+static u64 bu27008_calc_nlux(struct bu27008_data *data, unsigned int red,
+ unsigned int green, unsigned int blue, unsigned int ir,
+ unsigned int gain, unsigned int gain_ir, unsigned int time)
+{
+ s64 c1, c2, c3, nlux;
+
+ time /= 10000;
+ ir = NORM_CHAN_DATA_FOR_LX_CALC(ir, gain_ir, time);
+ red = NORM_CHAN_DATA_FOR_LX_CALC(red, gain, time);
+ green = NORM_CHAN_DATA_FOR_LX_CALC(green, gain, time);
+ blue = NORM_CHAN_DATA_FOR_LX_CALC(blue, gain, time);
I'd prefer to see the inputs parameters and the normalized version given different
names. Also the inputs are still u16, so nice to reflect that here.
So, you suggest we bring the data as u16 until here and only here we
assign it into 32bit variables when doing the 'normalization'? I'm sure
it works, but I dislike doing computations like multiplying u16 by u32
as I never know (out of my head) how the implicit type conversions work
and if we get some results cropped. Adding the casts to computation make
it less pretty for my eyes while having all variables in large enough
types does not leave me wondering if it works correctly and if explicit
casts are needed.
I am not strongly opposing this though if you insist - I am sure I can
at the end of the day get the code right - but I am afraid I will later
look at the code and wonder if it contains hideous issues...
Also when doing normalization I'd used fixed with types so there is no
confusion over what was intended (here u32)
Ok.
+
+ if ((u64)ir * 100LLU > 18LLU * (u64)green) {
Putting scaling for ir to the right and green to the left is
unusual. I'd chose one side and stick to it.
Sorry Jonathan. I must be a bit slow today but I just seem to not be
able to think how you would like to have this? I think this line is
somehow mappable to the:
IRratio = (IR > 0.18 * Green) ? 0 : 1
formula I got from HW colleagues and added in the comment preceding the
function.
+ c1 = -22370;
+ c2 = 321900;
+ c3 = -120371;
+ } else {
+ c1 = -10740;
+ c2 = 305415;
+ c3 = -129367;
+ }
+ nlux = c1 * red + c2 * green + c3 * blue;
+ if (nlux < 0)
+ nlux = 0;
return max(0, nlux); is a bit neater and makes
it clear this is simple clamping to possible values given unlikely we'll see
negative light sources :)
Ok. I should've remembered how you prefered max()/min() when clamping :)
+
+ return nlux;
+}
+
+static int bu27008_get_time_n_gains(struct bu27008_data *data,
+ unsigned int *gain, unsigned int *gain_ir, unsigned int *time)
+{
+ int ret;
+
+ ret = bu27008_get_gain(data, &data->gts, gain);
+ if (ret < 0)
+ return ret;
+
+ ret = bu27008_get_gain(data, &data->gts_ir, gain_ir);
+ if (ret < 0)
+ return ret;
+
+ ret = bu27008_get_int_time_us(data);
+ if (ret < 0)
+ return ret;
+
+ /* Max integration time is 400000i. Fits in signed int. */
+ *time = ret;
+
+ return 0;
+}
+
+struct bu27008_buf {
+ __le16 chan[BU27008_NUM_HW_CHANS];
+ u64 lux __aligned(8);
+ s64 ts __aligned(8);
+};
+
+static int bu27008_buffer_get_lux(struct bu27008_data *data,
+ struct bu27008_buf *raw)
+{
+ unsigned int red, green, blue, ir, gain, gain_ir, time;
+ int ret;
+
+ red = le16_to_cpu(raw->chan[0]);
+ green = le16_to_cpu(raw->chan[1]);
+ blue = le16_to_cpu(raw->chan[2]);
+ ir = le16_to_cpu(raw->chan[3]);
+ ret = bu27008_get_time_n_gains(data, &gain, &gain_ir, &time);
+ if (ret)
+ return ret;
+
+ raw->lux = bu27008_calc_nlux(data, red, green, blue, ir, gain, gain_ir,
+ time);
Probably call this function *fill_in_lux() or something like that because I'd expect
a *get_lux() function to return the lux value.
Ok. Makes sense.
Thanks for the review again!
Yours,
-- Matti
--
Matti Vaittinen
Linux kernel developer at ROHM Semiconductors
Oulu Finland
~~ When things go utterly wrong vim users can always type :help! ~~