Re: [PATCH RFC v5 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@xxxxxxxx> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for controlling
> a GPIO pin related to the USB host controller.
>
> Convert this function to use the new GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> Signed-off-by: Duje Mihanović <duje.mihanovic@xxxxxxxx>
> ---
>  arch/arm/mach-pxa/spitz.c      | 13 ++++++-------
>  drivers/usb/host/ohci-pxa27x.c |  7 +++++++
>  2 files changed, 13 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index cc691b199429..535e2b2e997b 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
>   * USB Host
>   ******************************************************************************/
>  #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
> +GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
> +               SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
> +
>  static int spitz_ohci_init(struct device *dev)
>  {
> -       int err;
> -
> -       err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
> -       if (err)
> -               return err;
> +       gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
>
>         /* Only Port 2 is connected, setup USB Port 2 Output Control Register */
>         UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
>
> -       return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
> +       return 0;
>  }
>
>  static void spitz_ohci_exit(struct device *dev)
>  {
> -       gpio_free(SPITZ_GPIO_USB_HOST);
> +       gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
>  }
>
>  static struct pxaohci_platform_data spitz_ohci_platform_data = {
> diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
> index 357d9aee38a3..876842b940c0 100644
> --- a/drivers/usb/host/ohci-pxa27x.c
> +++ b/drivers/usb/host/ohci-pxa27x.c
> @@ -121,6 +121,7 @@ struct pxa27x_ohci {
>         void __iomem    *mmio_base;
>         struct regulator *vbus[3];
>         bool            vbus_enabled[3];
> +       struct gpio_desc *usb_host;
>  };
>
>  #define to_pxa27x_ohci(hcd)    (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
> @@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
>         pxa_ohci = to_pxa27x_ohci(hcd);
>         pxa_ohci->clk = usb_clk;
>         pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
> +       pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);

Any reason not to use devm_gpiod_get_optional()?

Bart

> +       if (IS_ERR(pxa_ohci->usb_host))
> +               return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host),
> +                               "failed to get USB host GPIO\n");
>
>         for (i = 0; i < 3; ++i) {
>                 char name[6];
> @@ -512,6 +517,8 @@ static void ohci_hcd_pxa27x_remove(struct platform_device *pdev)
>         for (i = 0; i < 3; ++i)
>                 pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
>
> +       gpiod_put(pxa_ohci->usb_host);
> +
>         usb_put_hcd(hcd);
>  }
>
>
> --
> 2.42.0
>
>