Re: [PATCH v2] thermal/core: Don't update trip points inside the hysteresis range

[Rafael J. Wysocki]

On Mon, Sep 25, 2023 at 9:29 AM AngeloGioacchino Del Regno
<angelogioacchino.delregno@xxxxxxxxxxxxx> wrote:
>
> Il 22/09/23 20:44, Nícolas F. R. A. Prado ha scritto:
> > When searching for the trip points that need to be set, the nearest
> > higher trip point's temperature is used for the high trip, while the
> > nearest lower trip point's temperature minus the hysteresis is used for
> > the low trip. The issue with this logic is that when the current
> > temperature is inside a trip point's hysteresis range, both high and low
> > trips will come from the same trip point. As a consequence instability
> > can still occur like this:
> > * the temperature rises slightly and enters the hysteresis range of a
> >    trip point
> > * polling happens and updates the trip points to the hysteresis range
> > * the temperature falls slightly, exiting the hysteresis range, crossing
> >    the trip point and triggering an IRQ, the trip points are updated
> > * repeat
> >
> > So even though the current hysteresis implementation prevents
> > instability from happening due to IRQs triggering on the same
> > temperature value, both ways, it doesn't prevent it from happening due
> > to an IRQ on one way and polling on the other.
> >
> > To properly implement a hysteresis behavior, when inside the hysteresis
> > range, don't update the trip points. This way, the previously set trip
> > points will stay in effect, which will in a way remember the previous
> > state (if the temperature signal came from above or below the range) and
> > therefore have the right trip point already set. The exception is if
> > there was no previous trip point set, in which case a previous state
> > doesn't exist, and so it's sensible to allow the hysteresis range as
> > trip points.
> >
> > The following logs show the current behavior when running on a real
> > machine:
> >
> > [  202.524658] thermal thermal_zone0: new temperature boundaries: -2147483647 < x < 40000
> >     203.562817: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=36986 temp=37979
> > [  203.562845] thermal thermal_zone0: new temperature boundaries: 37000 < x < 40000
> >     204.176059: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=37979 temp=40028
> > [  204.176089] thermal thermal_zone0: new temperature boundaries: 37000 < x < 100000
> >     205.226813: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=40028 temp=38652
> > [  205.226842] thermal thermal_zone0: new temperature boundaries: 37000 < x < 40000
> >
> > And with this patch applied:
> >
> > [  184.933415] thermal thermal_zone0: new temperature boundaries: -2147483647 < x < 40000
> >     185.981182: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=36986 temp=37872
> >     186.744685: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=37872 temp=40058
> > [  186.744716] thermal thermal_zone0: new temperature boundaries: 37000 < x < 100000
> >     187.773284: thermal_temperature: thermal_zone=vpu0-thermal id=0 temp_prev=40058 temp=38698
> >
> > Fixes: 060c034a9741 ("thermal: Add support for hardware-tracked trip points")
> > Signed-off-by: Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx>
>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
>
> >
> > ---
> >
> > Changes in v2:
> > - Changed logic as suggested by Rafael
> > - Added log example to commit message
> > - Added fixes tag
> >
> >   drivers/thermal/thermal_trip.c | 19 +++++++++++++++++--
> >   1 file changed, 17 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/thermal/thermal_trip.c b/drivers/thermal/thermal_trip.c
> > index 024e2e365a26..597ac4144e33 100644
> > --- a/drivers/thermal/thermal_trip.c
> > +++ b/drivers/thermal/thermal_trip.c
> > @@ -55,6 +55,7 @@ void __thermal_zone_set_trips(struct thermal_zone_device *tz)
> >   {
> >       struct thermal_trip trip;
> >       int low = -INT_MAX, high = INT_MAX;
> > +     bool same_trip = false;
> >       int i, ret;
> >
> >       lockdep_assert_held(&tz->lock);
> > @@ -63,6 +64,7 @@ void __thermal_zone_set_trips(struct thermal_zone_device *tz)
> >               return;
> >
> >       for (i = 0; i < tz->num_trips; i++) {
> > +             bool low_set = false;
> >               int trip_low;
> >
> >               ret = __thermal_zone_get_trip(tz, i , &trip);
> > @@ -71,18 +73,31 @@ void __thermal_zone_set_trips(struct thermal_zone_device *tz)
> >
> >               trip_low = trip.temperature - trip.hysteresis;
> >
> > -             if (trip_low < tz->temperature && trip_low > low)
> > +             if (trip_low < tz->temperature && trip_low > low) {
> >                       low = trip_low;
> > +                     low_set = true;
> > +                     same_trip = false;
> > +             }
> >
> >               if (trip.temperature > tz->temperature &&
> > -                 trip.temperature < high)
> > +                 trip.temperature < high) {
> >                       high = trip.temperature;
> > +                     same_trip = low_set;
> > +             }
> >       }
> >
> >       /* No need to change trip points */
> >       if (tz->prev_low_trip == low && tz->prev_high_trip == high)
> >               return;
> >
> > +     /*
> > +      * If "high" and "low" are the same, skip the change unless this is the
> > +      * first time.
> > +      */
> > +     if (same_trip && (tz->prev_low_trip != -INT_MAX ||
> > +         tz->prev_high_trip != INT_MAX))
> > +             return;
> > +
> >       tz->prev_low_trip = low;
> >       tz->prev_high_trip = high;
> >

Applied as 6.7 material, but I added a Co-developed-by tag for myself,
because it has been based on my patch.

Thanks!