[PATCH net-next v5 5/7] ARM64: dts: marvell: Fix some common switch mistakes

From: Linus Walleij
Date: Mon Oct 23 2023 - 03:19:29 EST

Next message: Linus Walleij: "[PATCH net-next v5 4/7] ARM: dts: nxp: Fix some common switch mistakes"
Previous message: Linus Walleij: "[PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes"
In reply to: Linus Walleij: "[PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes"
Next in thread: Linus Walleij: "[PATCH net-next v5 4/7] ARM: dts: nxp: Fix some common switch mistakes"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@

Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
.../dts/marvell/armada-3720-espressobin-ultra.dts | 14 +-
.../boot/dts/marvell/armada-3720-espressobin.dtsi | 20 +--
.../boot/dts/marvell/armada-3720-gl-mv1000.dts | 20 +--
.../boot/dts/marvell/armada-3720-turris-mox.dts | 189 +++++++++++----------
.../boot/dts/marvell/armada-7040-mochabin.dts | 24 ++-
.../dts/marvell/armada-8040-clearfog-gt-8k.dts | 22 +--
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 42 +++--
7 files changed, 164 insertions(+), 167 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
index f9abef8dcc94..870bb380a40a 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -126,32 +126,32 @@ &switch0 {

reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;

- ports {
- switch0port1: port@1 {
+ ethernet-ports {
+ switch0port1: ethernet-port@1 {
reg = <1>;
label = "lan0";
phy-handle = <&switch0phy0>;
};

- switch0port2: port@2 {
+ switch0port2: ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&switch0phy1>;
};

- switch0port3: port@3 {
+ switch0port3: ethernet-port@3 {
reg = <3>;
label = "lan2";
phy-handle = <&switch0phy2>;
};

- switch0port4: port@4 {
+ switch0port4: ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&switch0phy3>;
};

- switch0port5: port@5 {
+ switch0port5: ethernet-port@5 {
reg = <5>;
label = "wan";
phy-handle = <&extphy>;
@@ -160,7 +160,7 @@ switch0port5: port@5 {
};

mdio {
- switch0phy3: switch0phy3@14 {
+ switch0phy3: ethernet-phy@14 {
reg = <0x14>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index 5fc613d24151..86ec0df1c676 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -145,19 +145,17 @@ &usb2 {
};

&mdio {
- switch0: switch0@1 {
+ switch0: ethernet-switch@1 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;

dsa,member = <0 0>;

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- switch0port0: port@0 {
+ switch0port0: ethernet-port@0 {
reg = <0>;
label = "cpu";
ethernet = <&eth0>;
@@ -168,19 +166,19 @@ fixed-link {
};
};

- switch0port1: port@1 {
+ switch0port1: ethernet-port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};

- switch0port2: port@2 {
+ switch0port2: ethernet-port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
};

- switch0port3: port@3 {
+ switch0port3: ethernet-port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
@@ -192,13 +190,13 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
index b1b45b4fa9d4..63fbc8352161 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
@@ -152,31 +152,29 @@ &uart0 {
};

&mdio {
- switch0: switch0@1 {
+ switch0: ethernet-switch@1 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;

dsa,member = <0 0>;

- ports: ports {
+ ports: ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "cpu";
ethernet = <&eth0>;
};

- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};

- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
@@ -185,7 +183,7 @@ port@2 {
nvmem-cell-names = "mac-address";
};

- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
@@ -199,13 +197,13 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index 9eab2bb22134..cdf1b8bdb230 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -304,7 +304,12 @@ phy1: ethernet-phy@1 {
reg = <1>;
};

- /* switch nodes are enabled by U-Boot if modules are present */
+ /*
+ * NOTE: switch nodes are enabled by U-Boot if modules are present
+ * DO NOT change this node name (switch0@10) even if it is not following
+ * conventions! Deployed U-Boot binaries are explicitly looking for
+ * this node in order to augment the device tree!
+ */
switch0@10 {
compatible = "marvell,mv88e6190";
reg = <0x10>;
@@ -317,92 +322,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};

- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};

- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};

- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};

- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};

- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};

- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};

- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan5";
phy-handle = <&switch0phy5>;
};

- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan6";
phy-handle = <&switch0phy6>;
};

- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan7";
phy-handle = <&switch0phy7>;
};

- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan8";
phy-handle = <&switch0phy8>;
};

- port@9 {
+ ethernet-port@9 {
reg = <0x9>;
label = "cpu";
ethernet = <&eth1>;
@@ -410,7 +415,7 @@ port@9 {
managed = "in-band-status";
};

- switch0port10: port@a {
+ switch0port10: ethernet-port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
@@ -430,7 +435,7 @@ port-sfp@a {
};
};

- switch0@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 0>;
@@ -442,52 +447,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy1_topaz: switch0phy1@11 {
+ switch0phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};

- switch0phy2_topaz: switch0phy2@12 {
+ switch0phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};

- switch0phy3_topaz: switch0phy3@13 {
+ switch0phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};

- switch0phy4_topaz: switch0phy4@14 {
+ switch0phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1_topaz>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2_topaz>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3_topaz>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4_topaz>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "cpu";
phy-mode = "2500base-x";
@@ -497,7 +502,7 @@ port@5 {
};
};

- switch1@11 {
+ ethernet-switch@11 {
compatible = "marvell,mv88e6190";
reg = <0x11>;
dsa,member = <0 1>;
@@ -509,92 +514,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch1phy1: switch1phy1@1 {
+ switch1phy1: ethernet-phy@1 {
reg = <0x1>;
};

- switch1phy2: switch1phy2@2 {
+ switch1phy2: ethernet-phy@2 {
reg = <0x2>;
};

- switch1phy3: switch1phy3@3 {
+ switch1phy3: ethernet-phy@3 {
reg = <0x3>;
};

- switch1phy4: switch1phy4@4 {
+ switch1phy4: ethernet-phy@4 {
reg = <0x4>;
};

- switch1phy5: switch1phy5@5 {
+ switch1phy5: ethernet-phy@5 {
reg = <0x5>;
};

- switch1phy6: switch1phy6@6 {
+ switch1phy6: ethernet-phy@6 {
reg = <0x6>;
};

- switch1phy7: switch1phy7@7 {
+ switch1phy7: ethernet-phy@7 {
reg = <0x7>;
};

- switch1phy8: switch1phy8@8 {
+ switch1phy8: ethernet-phy@8 {
reg = <0x8>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan13";
phy-handle = <&switch1phy5>;
};

- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan14";
phy-handle = <&switch1phy6>;
};

- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan15";
phy-handle = <&switch1phy7>;
};

- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan16";
phy-handle = <&switch1phy8>;
};

- switch1port9: port@9 {
+ switch1port9: ethernet-port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -602,7 +607,7 @@ switch1port9: port@9 {
link = <&switch0port10>;
};

- switch1port10: port@a {
+ switch1port10: ethernet-port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
@@ -622,7 +627,7 @@ port-sfp@a {
};
};

- switch1@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 1>;
@@ -634,52 +639,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch1phy1_topaz: switch1phy1@11 {
+ switch1phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};

- switch1phy2_topaz: switch1phy2@12 {
+ switch1phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};

- switch1phy3_topaz: switch1phy3@13 {
+ switch1phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};

- switch1phy4_topaz: switch1phy4@14 {
+ switch1phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1_topaz>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2_topaz>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3_topaz>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4_topaz>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
@@ -689,7 +694,7 @@ port@5 {
};
};

- switch2@12 {
+ ethernet-switch@12 {
compatible = "marvell,mv88e6190";
reg = <0x12>;
dsa,member = <0 2>;
@@ -701,92 +706,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch2phy1: switch2phy1@1 {
+ switch2phy1: ethernet-phy@1 {
reg = <0x1>;
};

- switch2phy2: switch2phy2@2 {
+ switch2phy2: ethernet-phy@2 {
reg = <0x2>;
};

- switch2phy3: switch2phy3@3 {
+ switch2phy3: ethernet-phy@3 {
reg = <0x3>;
};

- switch2phy4: switch2phy4@4 {
+ switch2phy4: ethernet-phy@4 {
reg = <0x4>;
};

- switch2phy5: switch2phy5@5 {
+ switch2phy5: ethernet-phy@5 {
reg = <0x5>;
};

- switch2phy6: switch2phy6@6 {
+ switch2phy6: ethernet-phy@6 {
reg = <0x6>;
};

- switch2phy7: switch2phy7@7 {
+ switch2phy7: ethernet-phy@7 {
reg = <0x7>;
};

- switch2phy8: switch2phy8@8 {
+ switch2phy8: ethernet-phy@8 {
reg = <0x8>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan21";
phy-handle = <&switch2phy5>;
};

- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan22";
phy-handle = <&switch2phy6>;
};

- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan23";
phy-handle = <&switch2phy7>;
};

- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan24";
phy-handle = <&switch2phy8>;
};

- switch2port9: port@9 {
+ switch2port9: ethernet-port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -805,7 +810,7 @@ port-sfp@a {
};
};

- switch2@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 2>;
@@ -817,52 +822,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch2phy1_topaz: switch2phy1@11 {
+ switch2phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};

- switch2phy2_topaz: switch2phy2@12 {
+ switch2phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};

- switch2phy3_topaz: switch2phy3@13 {
+ switch2phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};

- switch2phy4_topaz: switch2phy4@14 {
+ switch2phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1_topaz>;
};

- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2_topaz>;
};

- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3_topaz>;
};

- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4_topaz>;
};

- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
index 48202810bf78..40b7ee7ead72 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -301,10 +301,8 @@ eth2phy: ethernet-phy@1 {
};

/* 88E6141 Topaz switch */
- switch: switch@3 {
+ switch: ethernet-switch@3 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <3>;

pinctrl-names = "default";
@@ -314,35 +312,35 @@ switch: switch@3 {
interrupt-parent = <&cp0_gpio1>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- swport1: port@1 {
+ swport1: ethernet-port@1 {
reg = <1>;
label = "lan0";
phy-handle = <&swphy1>;
};

- swport2: port@2 {
+ swport2: ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&swphy2>;
};

- swport3: port@3 {
+ swport3: ethernet-port@3 {
reg = <3>;
label = "lan2";
phy-handle = <&swphy3>;
};

- swport4: port@4 {
+ swport4: ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&swphy4>;
};

- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp0_eth1>;
@@ -355,19 +353,19 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- swphy1: swphy1@17 {
+ swphy1: ethernet-phy@17 {
reg = <17>;
};

- swphy2: swphy2@18 {
+ swphy2: ethernet-phy@18 {
reg = <18>;
};

- swphy3: swphy3@19 {
+ swphy3: ethernet-phy@19 {
reg = <19>;
};

- swphy4: swphy4@20 {
+ swphy4: ethernet-phy@20 {
reg = <20>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index 4125202028c8..67892f0d2863 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -497,42 +497,42 @@ ge_phy: ethernet-phy@0 {
reset-deassert-us = <10000>;
};

- switch0: switch0@4 {
+ switch0: ethernet-switch@4 {
compatible = "marvell,mv88e6085";
reg = <4>;
pinctrl-names = "default";
pinctrl-0 = <&cp1_switch_reset_pins>;
reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>;

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan2";
phy-handle = <&switch0phy0>;
};

- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&switch0phy1>;
};

- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan4";
phy-handle = <&switch0phy2>;
};

- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&switch0phy3>;
};

- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
@@ -545,19 +545,19 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};

- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};

- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};

- switch0phy3: switch0phy3@14 {
+ switch0phy3: ethernet-phy@14 {
reg = <0x14>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 32cfb3e2efc3..7538ed56053b 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -207,11 +207,9 @@ phy0: ethernet-phy@0 {
reg = <0>;
};

- switch6: switch0@6 {
+ switch6: ethernet-switch@6 {
/* Actual device is MV88E6393X */
compatible = "marvell,mv88e6190";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <6>;
interrupt-parent = <&cp0_gpio1>;
interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
@@ -220,59 +218,59 @@ switch6: switch0@6 {

dsa,member = <0 0>;

- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;

- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "p1";
phy-handle = <&switch0phy1>;
};

- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "p2";
phy-handle = <&switch0phy2>;
};

- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "p3";
phy-handle = <&switch0phy3>;
};

- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "p4";
phy-handle = <&switch0phy4>;
};

- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "p5";
phy-handle = <&switch0phy5>;
};

- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "p6";
phy-handle = <&switch0phy6>;
};

- port@7 {
+ ethernet-port@7 {
reg = <7>;
label = "p7";
phy-handle = <&switch0phy7>;
};

- port@8 {
+ ethernet-port@8 {
reg = <8>;
label = "p8";
phy-handle = <&switch0phy8>;
};

- port@9 {
+ ethernet-port@9 {
reg = <9>;
label = "p9";
phy-mode = "10gbase-r";
@@ -280,7 +278,7 @@ port@9 {
managed = "in-band-status";
};

- port@a {
+ ethernet-port@a {
reg = <10>;
ethernet = <&cp0_eth0>;
phy-mode = "10gbase-r";
@@ -293,35 +291,35 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;

- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};

- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};

- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};

- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};

- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};

- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};

- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};

- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};

--
2.34.1

Next message: Linus Walleij: "[PATCH net-next v5 4/7] ARM: dts: nxp: Fix some common switch mistakes"
Previous message: Linus Walleij: "[PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes"
In reply to: Linus Walleij: "[PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes"
Next in thread: Linus Walleij: "[PATCH net-next v5 4/7] ARM: dts: nxp: Fix some common switch mistakes"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]