Re: [PATCH v2 2/7] scsi: ufs: ufs-qcom: Setup host power mode during init

[Manivannan Sadhasivam]

On Mon, Nov 06, 2023 at 08:46:08PM -0800, Can Guo wrote:
> From: Can Guo <quic_cang@xxxxxxxxxxx>
> 
> Setup host power mode and its limitations during UFS host driver init to
> avoid repetitive work during every power mode change.
> 
> Co-developed-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
> Signed-off-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
> Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
> ---
>  drivers/ufs/host/ufs-qcom.c | 22 ++++++++++++++--------
>  drivers/ufs/host/ufs-qcom.h |  1 +
>  2 files changed, 15 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index aee66a3..cc0eb37 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -898,7 +898,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>  				struct ufs_pa_layer_attr *dev_req_params)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> -	struct ufs_host_params host_params;
> +	struct ufs_host_params *host_params = &host->host_params;
>  	int ret = 0;
>  
>  	if (!dev_req_params) {
> @@ -908,13 +908,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>  
>  	switch (status) {
>  	case PRE_CHANGE:
> -		ufshcd_init_host_param(&host_params);
> -		host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;

As Andrew spotted, this gets removed without explanation. So, I'd also suggest
doing it in a separate patch.

- Mani

> -
> -		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> -		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> -
> -		ret = ufshcd_negotiate_pwr_param(&host_params, dev_max_params, dev_req_params);
> +		ret = ufshcd_negotiate_pwr_param(host_params, dev_max_params, dev_req_params);
>  		if (ret) {
>  			dev_err(hba->dev, "%s: failed to determine capabilities\n",
>  					__func__);
> @@ -1049,6 +1043,17 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
>  		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
>  }
>  
> +static void ufs_qcom_set_host_params(struct ufs_hba *hba)
> +{
> +	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +	struct ufs_host_params *host_params = &host->host_params;
> +
> +	ufshcd_init_host_param(host_params);
> +
> +	/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> +	host_params->hs_tx_gear = host_params->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
> +}
> +
>  static void ufs_qcom_set_caps(struct ufs_hba *hba)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> @@ -1273,6 +1278,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>  
>  	ufs_qcom_set_caps(hba);
>  	ufs_qcom_advertise_quirks(hba);
> +	ufs_qcom_set_host_params(hba);
>  
>  	err = ufs_qcom_ice_init(host);
>  	if (err)
> diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
> index 9950a00..ab94c54 100644
> --- a/drivers/ufs/host/ufs-qcom.h
> +++ b/drivers/ufs/host/ufs-qcom.h
> @@ -240,6 +240,7 @@ struct ufs_qcom_host {
>  
>  	struct gpio_desc *device_reset;
>  
> +	struct ufs_host_params host_params;
>  	u32 phy_gear;
>  
>  	bool esi_enabled;
> -- 
> 2.7.4
> 

-- 
மணிவண்ணன் சதாசிவம்