Re: [net-next PATCH RFC v3 1/8] dt-bindings: net: document ethernet PHY package nodes

[Rob Herring]

On Sun, Nov 26, 2023 at 02:53:39AM +0100, Christian Marangi wrote:
> Document ethernet PHY package nodes used to describe PHY shipped in
> bundle of 4-5 PHY. The special node describe a container of PHY that
> share common properties. This is a generic schema and PHY package
> should create specialized version with the required additional shared
> properties.
> 
> Example are PHY package that have some regs only in one PHY of the
> package and will affect every other PHY in the package, for example
> related to PHY interface mode calibration or global PHY mode selection.
> 
> The PHY package node MUST declare the base address used by the PHY driver
> for global configuration by calculating the offsets of the global PHY
> based on the base address of the PHY package and declare the
> "ethrnet-phy-package" compatible.
> 
> Each reg of the PHY defined in the PHY package node is absolute and will
> reference the real address of the PHY on the bus.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> ---
>  .../bindings/net/ethernet-phy-package.yaml    | 75 +++++++++++++++++++
>  1 file changed, 75 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml b/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> new file mode 100644
> index 000000000000..244d4bc29164
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> @@ -0,0 +1,75 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/ethernet-phy-package.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Ethernet PHY Package Common Properties
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@xxxxxxxxx>
> +
> +description:
> +  This schema describe PHY package as simple container for
> +  a bundle of PHYs that share the same properties and
> +  contains the PHYs of the package themself.
> +
> +  Each reg of the PHYs defined in the PHY package node is
> +  absolute and describe the real address of the PHY on the bus.
> +
> +properties:
> +  $nodename:
> +    pattern: "^ethernet-phy-package(@[a-f0-9]+)?$"
> +
> +  compatible:
> +    const: ethernet-phy-package

In case I wasn't clear, but that compatible is a NAK.

> +
> +  reg:
> +    minimum: 0
> +    maximum: 31

Pretty sure the bus binding already provides these constraints.

> +    description:
> +      The base ID number for the PHY package.
> +      Commonly the ID of the first PHY in the PHY package.
> +
> +      Some PHY in the PHY package might be not defined but
> +      still exist on the device (just not attached to anything).
> +      The reg defined in the PHY package node might differ and
> +      the related PHY might be not defined.
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0

You are implementing a secondary MDIO bus within this node. It needs a 
$ref to mdio.yaml instead of defining the bus again implicitly.

> +
> +patternProperties:
> +  ^ethernet-phy(@[a-f0-9]+)?$:
> +    $ref: ethernet-phy.yaml#
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: true
> +
> +examples:
> +  - |
> +    mdio {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        ethernet-phy-package@16 {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +            compatible = "ethernet-phy-package";
> +            reg = <0x16>;
> +
> +            ethernet-phy@16 {
> +              reg = <0x16>;
> +            };
> +
> +            phy4: ethernet-phy@1a {
> +              reg = <0x1a>;
> +            };

This example on its own doesn't make sense. It can't be fully validated 
because you allow any additional properties. Drop it.

> +        };
> +    };
> -- 
> 2.40.1
>