Re: [PATCH v2] usb: hub: Add quirk to decrease IN-ep poll interval for Microchip USB491x hub

[Alan Stern]

On Thu, Nov 30, 2023 at 09:48:55AM +0100, Hardik Gajjar wrote:
> There is a potential delay in notifying Linux USB drivers of downstream
> USB bus activity when connecting a high-speed or superSpeed device via the
> Microchip USB491x hub. This delay is due to the fixed bInterval value of
> 12 in the silicon of the Microchip USB491x hub.
> 
> Microchip requested to ignore the device descriptor and decrease that
> value to 9 as it was too late to modify that in silicon.
> 
> This patch speeds up the USB enummeration process that helps to pass
> Apple Carplay certifications and improve the User experience when utilizing
> the USB device via Microchip Multihost USB491x Hub.
> 
> A new hub quirk HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL speeds up
> the notification process for Microchip USB491x hub by limiting
> the maximum bInterval value to 9.
> 
> Signed-off-by: Hardik Gajjar <hgajjar@xxxxxxxxxxxxxx>
> ---
> changes since version 1:
> 	- Move implementation from config.c and quirk.c to hub.c as this is hub
> 	  specific changes.
> 	- Improve commit message.
> 	- Link to v1 - https://lore.kernel.org/all/20231123081948.58776-1-hgajjar@xxxxxxxxxxxxxx/
> ---
>  drivers/usb/core/hub.c | 27 +++++++++++++++++++++++++++
>  1 file changed, 27 insertions(+)
> 
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> index b4584a0cd484..3d26d942fcae 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -47,12 +47,18 @@
>  #define USB_VENDOR_TEXAS_INSTRUMENTS		0x0451
>  #define USB_PRODUCT_TUSB8041_USB3		0x8140
>  #define USB_PRODUCT_TUSB8041_USB2		0x8142
> +#define USB_VENDOR_MICROCHIP			0x0424
> +#define USB_PRODUCT_USB4913			0x4913
> +#define USB_PRODUCT_USB4914			0x4914
> +#define USB_PRODUCT_USB4915			0x4915
>  #define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND	0x01
>  #define HUB_QUIRK_DISABLE_AUTOSUSPEND		0x02
> +#define HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL	0x08

Why not use 0x04, the next available bit?

>  
>  #define USB_TP_TRANSMISSION_DELAY	40	/* ns */
>  #define USB_TP_TRANSMISSION_DELAY_MAX	65535	/* ns */
>  #define USB_PING_RESPONSE_TIME		400	/* ns */
> +#define USB_REDUCE_FRAME_INTR_BINTERVAL	9
>  
>  /* Protect struct usb_device->state and ->children members
>   * Note: Both are also protected by ->dev.sem, except that ->state can
> @@ -1927,6 +1933,12 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id)
>  		usb_autopm_get_interface_no_resume(intf);
>  	}
>  
> +	if ((id->driver_info & HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL) &&
> +	    desc->endpoint[0].desc.bInterval > USB_REDUCE_FRAME_INTR_BINTERVAL) {
> +		desc->endpoint[0].desc.bInterval =
> +			USB_REDUCE_FRAME_INTR_BINTERVAL;

As I mentioned in an earlier email, you need to do:

		/* Tell the HCD about the interrupt ep's new bInterval */
		usb_set_interface(hdev, 0, 0);

here.  Everything else looks okay (and much better than before).

Alan Stern

> +	}
> +
>  	if (hub_configure(hub, &desc->endpoint[0].desc) >= 0) {
>  		onboard_hub_create_pdevs(hdev, &hub->onboard_hub_devs);
>  
> @@ -5918,6 +5930,21 @@ static const struct usb_device_id hub_id_table[] = {
>        .idVendor = USB_VENDOR_TEXAS_INSTRUMENTS,
>        .idProduct = USB_PRODUCT_TUSB8041_USB3,
>        .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND},
> +	{ .match_flags = USB_DEVICE_ID_MATCH_VENDOR
> +			| USB_DEVICE_ID_MATCH_PRODUCT,
> +	  .idVendor = USB_VENDOR_MICROCHIP,
> +	  .idProduct = USB_PRODUCT_USB4913,
> +	  .driver_info = HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL},
> +	{ .match_flags = USB_DEVICE_ID_MATCH_VENDOR
> +			| USB_DEVICE_ID_MATCH_PRODUCT,
> +	  .idVendor = USB_VENDOR_MICROCHIP,
> +	  .idProduct = USB_PRODUCT_USB4914,
> +	  .driver_info = HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL},
> +	{ .match_flags = USB_DEVICE_ID_MATCH_VENDOR
> +			| USB_DEVICE_ID_MATCH_PRODUCT,
> +	  .idVendor = USB_VENDOR_MICROCHIP,
> +	  .idProduct = USB_PRODUCT_USB4915,
> +	  .driver_info = HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL},
>      { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS,
>        .bDeviceClass = USB_CLASS_HUB},
>      { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS,
> -- 
> 2.17.1
>