Re: [PATCH v4 3/3] arm64: dts: freescale: introduce rve-gateway board

From: Hugo Villeneuve
Date: Tue Dec 05 2023 - 09:37:10 EST

On Tue, 5 Dec 2023 20:27:56 +0800
Shawn Guo <shawnguo@xxxxxxxxxx> wrote:

> On Fri, Nov 03, 2023 at 10:28:31AM -0400, Hugo Villeneuve wrote:
> > From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> >
> > The RVE gateway board is based on a Variscite VAR-SOM-NANO,
> > with a NXP MX8MN nano CPU.
> >
> > Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../boot/dts/freescale/imx8mn-rve-gateway.dts | 282 ++++++++++++++++++
> > 2 files changed, 283 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 300049037eb0..c99da779ef7b 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -98,6 +98,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr3l-evk.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mn-rve-gateway.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> > new file mode 100644
> > index 000000000000..186f54fd06c6
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> > @@ -0,0 +1,282 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright 2023 DimOnOff
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/usb/pd.h>
> > +#include "imx8mn-var-som.dtsi"
> > +
> > +/ {
> > + model = "RVE gateway";
> > + compatible = "rve,rve-gateway", "variscite,var-som-mx8mn", "fsl,imx8mn";
> > +
> > + crystal_duart_24m: crystal-duart-24m {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <24000000>;
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpio_keys>;
> > +
> > + key-enter {
> > + label = "enter";
> > + gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_ENTER>;
> > + };
> > +
> > + key-exit {
> > + label = "exit";
> > + gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_ESC>;
> > + };
> > + };
> > +
> > + lcd {
> > + compatible = "hit,hd44780";
> > + display-height-chars = <2>;
> > + display-width-chars = <20>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lcd>;
> > + data-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>,
> > + <&gpio1 6 GPIO_ACTIVE_HIGH>,
> > + <&gpio1 14 GPIO_ACTIVE_HIGH>,
> > + <&gpio4 28 GPIO_ACTIVE_HIGH>,
> > + <&gpio5 24 GPIO_ACTIVE_HIGH>,
> > + <&gpio5 2 GPIO_ACTIVE_HIGH>,
> > + <&gpio1 12 GPIO_ACTIVE_HIGH>,
> > + <&gpio5 25 GPIO_ACTIVE_HIGH>;
> > + enable-gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
> > + rs-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> > + rw-gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + reg_3p3v: regulator-3p3v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3P3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + /* Bourns PEC12R rotary encoder, 24 steps. */
> > + rotary: rotary-encoder {
> > + compatible = "rotary-encoder";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rotary>;
> > + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>, /* A */
> > + <&gpio3 21 GPIO_ACTIVE_LOW>; /* B */
> > + linux,axis = <0>; /* REL_X */
> > + rotary-encoder,encoding = "gray";
> > + rotary-encoder,relative-axis;
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> > +
> > + duart1: serial@0 {
> > + compatible = "nxp,sc16is752";
> > + reg = <0>;
> > + spi-rx-bus-width = <1>;
> > + spi-tx-bus-width = <1>;
> > + spi-max-frequency = <4000000>;
> > + clocks = <&crystal_duart_24m>;
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-line-names = "RADIO0", "RADIO1", "RADIO2", "RADIO3",
> > + "RADIO4", "RADIO_RESET", "TP12", "TP11";
>
> Can we add some indent to get the line aligned with the first " above?
> There are a few such lines that could be improved.

Hi,
Sure, will do for V5.

Hugo.


>
> Shawn
>
> > + linux,rs485-enabled-at-boot-time;
> > + rs485-rts-active-low;
> > + };
> > +
> > + /delete-node/ touchscreen@0;
> > +};
> > +
> > +&ecspi2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi2>;
> > + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> > + /delete-property/ dmas;
> > + /delete-property/ dma-names;
> > + status = "okay";
> > +
> > + duart2: serial@0 {
> > + compatible = "nxp,sc16is752";
> > + reg = <0>;
> > + spi-rx-bus-width = <1>;
> > + spi-tx-bus-width = <1>;
> > + spi-max-frequency = <4000000>;
> > + clocks = <&crystal_duart_24m>;
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-line-names = "LED_B_USER", "LED_R_USER", "LED_G_USER",
> > + "GPIO_EXT3", "GPIO_EXT2", "GPIO_EXT1", "GPIO_EXT0", "TP13";
> > + linux,rs485-enabled-at-boot-time;
> > + rs485-rts-active-low;
> > + };
> > +};
> > +
> > +/* Configure PWM pins in GPIO mode: */
> > +&gpio5 {
> > + gpio-line-names = "", "", "", "PWM3", "PWM2", "PWM1";
> > +};
> > +
> > +&gpu {
> > + status = "disabled";
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + /* Carrier board EEPROM */
> > + eeprom_cb: eeprom@56 {
> > + compatible = "atmel,24c04";
> > + reg = <0x56>;
> > + pagesize = <16>;
> > + vcc-supply = <&reg_3p3v>;
> > + };
> > +
> > + lm75: sensor@48 {
> > + compatible = "st,stlm75";
> > + reg = <0x48>;
> > + vs-supply = <&reg_3p3v>;
> > + };
> > +
> > + mcp7940: rtc@6f {
> > + compatible = "microchip,mcp7940x";
> > + reg = <0x6f>;
> > + };
> > +};
> > +
> > +&i2c3 {
> > + codec@1a {
> > + status = "disabled";
> > + };
> > +};
> > +
> > +&i2c4 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c4>;
> > + status = "okay";
> > +
> > + pcf8574_1: gpio@38 {
> > + compatible = "nxp,pcf8574";
> > + reg = <0x38>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-line-names = "LED_B_COMM3", "LED_R_COMM3", "LED_G_COMM3",
> > + "TP14", "TP15", "LED_G_COMM4", "LED_R_COMM4", "LED_B_COMM4";
> > + };
> > +
> > + pcf8574_2: gpio@39 {
> > + compatible = "nxp,pcf8574";
> > + reg = <0x39>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-line-names = "LED_B_COMM2", "LED_G_COMM2", "LED_B_COMM1",
> > + "LED_R_COMM2", "LED_R_COMM1", "LED_G_COMM1", "TP16", "TP17";
> > + };
> > +};
> > +
> > +/* Bluetooth */
> > +&uart2 {
> > + status = "disabled";
> > +};
> > +
> > +&usbotg1 {
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +/* SD interface on expansion connector. */
> > +&usdhc2 {
> > + vmmc-supply = <&reg_3p3v>;
> > + cd-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
> > +};
> > +
> > +&iomuxc {
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13
> > + MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13
> > + MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13
> > + MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x13 /* SS0 */
> > + MX8MN_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x13 /* SC16 IRQ */
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x13
> > + MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x13
> > + MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x13
> > + MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x13 /* SS0 */
> > + MX8MN_IOMUXC_SAI5_RXC_GPIO3_IO20 0x13 /* SC16 IRQ */
> > + >;
> > + };
> > +
> > + pinctrl_gpio_keys: gpiokeysgrp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_GPIO1_IO01_GPIO1_IO1 0xc6 /* Enter */
> > + MX8MN_IOMUXC_SAI5_RXD2_GPIO3_IO23 0xc6 /* Exit */
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
> > + MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_i2c4: i2c4grp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3
> > + MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_lcd: lcdgrp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_SAI3_TXD_GPIO5_IO1 0x00000156 /* D0 */
> > + MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x00000156 /* D1 */
> > + MX8MN_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x00000156 /* D2 */
> > + MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x00000156 /* D3 */
> > + MX8MN_IOMUXC_UART2_RXD_GPIO5_IO24 0x00000156 /* D4 */
> > + MX8MN_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x00000156 /* D5 */
> > + MX8MN_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x00000156 /* D6 */
> > + MX8MN_IOMUXC_UART2_TXD_GPIO5_IO25 0x00000156 /* D7 */
> > + MX8MN_IOMUXC_UART1_TXD_GPIO5_IO23 0x00000156 /* E */
> > + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x00000156 /* RS */
> > + MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x00000156 /* R/W */
> > + >;
> > + };
> > +
> > + pinctrl_rotary: rotarygrp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x00000156 /* A */
> > + MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x00000156 /* B */
> > + >;
> > + };
> > +
> > + /* Override Card Detect function GPIO value (GPIO1_IO10) from SOM: */
> > + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> > + fsl,pins = <
> > + MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x41
> > + >;
> > + };
> > +};
> > --
> > 2.39.2
> >


--
Hugo Villeneuve