Re: [PATCH 00/11] ARM/arm64: dts: qcom: fix USB wakeup interrupt types

[Johan Hovold]

On Tue, Dec 12, 2023 at 03:00:07PM +0530, Krishna Kurapati PSSNV wrote:
> On 12/11/2023 10:09 PM, Johan Hovold wrote:
> > On Mon, Nov 20, 2023 at 05:43:20PM +0100, Johan Hovold wrote:

> > Konrad reported off-list that the sc8180x patch in this series breaks
> > probe of the dwc3 driver.
> > 
> > Turns out a number of these SoCs were using GIC interrupts for the
> > DP/DM_HS_PHY interrupts despite the fact that the driver tries to
> > reconfigure these as IRQ_TYPE_EDGE_FALLING (which the GIC does not
> > support) to detect disconnect events during suspend.
> > 
> > This is obviously broken and the proper fix is to replace the GIC
> > interrupts with the corresponding PDC interrupts. I believe Konrad is
> > digging out the magic numbers at this moment.
> > 
> > The following patches will need a follow-up fix:
> > 
> >>    ARM: dts: qcom: sdx55: fix USB wakeup interrupt types
> > 
> >>    arm64: dts: qcom: sc8180x: fix USB wakeup interrupt types
> >>    arm64: dts: qcom: sdm670: fix USB wakeup interrupt types
> >>    arm64: dts: qcom: sdm845: fix USB wakeup interrupt types
> >>    arm64: dts: qcom: sm6375: fix USB wakeup interrupt types
> >>    arm64: dts: qcom: sm8150: fix USB wakeup interrupt types

>   If it helps, I tried to dig up the PDC numbers for corresponding 
> GIC_SPI vectors:

Thanks, Krisha, that helps a lot.

I've sent two series (for arm and arm64) based on yours and Konrad's
input:

	https://lore.kernel.org/lkml/20231213173131.29436-1-johan+linaro@xxxxxxxxxx/
	https://lore.kernel.org/lkml/20231213173403.29544-1-johan+linaro@xxxxxxxxxx/

> SM8150:
> 
> eud_p0_dpse_int_mx	apps_pdc_irq_out[9]	SYS_apcsQgicSPI[489]
> eud_p0_dmse_int_mx    apps_pdc_irq_out[8]	SYS_apcsQgicSPI[488]
> qmp_usb3_lfps_rxterm_irq apps_pdc_irq_out[6]	SYS_apcsQgicSPI[486]
> usb31_power_event_irq	SYS_apcsQgicSPI[130]
> usb31_hs_phy_irq	SYS_apcsQgicSPI[131]
> 
> interrupts-extended = <&pdc 9 IRQ_TYPE_EDGE_RISING>,
> 			<&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> 			<&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
> 			<&pdc 8 IRQ_TYPE_EDGE_RISING>;
> 
> interrupt-names = "dp_hs_phy_irq", "pwr_event_irq",
> 		"ss_phy_irq", "dm_hs_phy_irq";

Do you have the corresponding numbers also for the second controller on
SM8150? I inferred them from SDM845, but it would good to verify that.

And can someone dig out the corresponding SS PHY interrupt for sc8180x?

Johan