Re: [PATCH 2/2] ARM: dts: qcom: msm8926-motorola-peregrine: Add initial device tree

[Krzysztof Kozlowski]

On 13/12/2023 21:33, André Apitzsch wrote:
> This dts adds support for Motorola Moto G 4G released in 2013.
> 
> Add a device tree with initial support for:
> 
> - GPIO keys
> - Hall sensor
> - SDHCI
> - Vibrator
> 
> Signed-off-by: André Apitzsch <git@xxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/qcom/Makefile                    |   1 +
>  .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 297 +++++++++++++++++++++
>  2 files changed, 298 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
> index 0cb272f4fa45..9cc1e14e6cd0 100644
> --- a/arch/arm/boot/dts/qcom/Makefile
> +++ b/arch/arm/boot/dts/qcom/Makefile
> @@ -35,6 +35,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
>  	qcom-msm8926-htc-memul.dtb \
>  	qcom-msm8926-microsoft-superman-lte.dtb \
>  	qcom-msm8926-microsoft-tesla.dtb \
> +	qcom-msm8926-motorola-peregrine.dtb \
>  	qcom-msm8960-cdp.dtb \
>  	qcom-msm8960-samsung-expressatt.dtb \
>  	qcom-msm8974-lge-nexus5-hammerhead.dtb \
> diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
> new file mode 100644
> index 000000000000..3c5256120502
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
> @@ -0,0 +1,297 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +
> +/dts-v1/;
> +
> +#include "qcom-msm8226.dtsi"
> +#include "pm8226.dtsi"
> +
> +/delete-node/ &smem_region;
> +
> +/ {
> +	model = "Motorola Moto G 4G";
> +	compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226";
> +	chassis-type = "handset";
> +
> +	aliases {
> +		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> +		mmc1 = &sdhc_2; /* SDC2 SD card slot */
> +	};
> +
> +	chosen {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		framebuffer0: framebuffer@3200000 {
> +			compatible = "simple-framebuffer";
> +			reg = <0x03200000 0x800000>;
> +			width = <720>;
> +			height = <1280>;
> +			stride = <(720 * 3)>;
> +			format = "r8g8b8";
> +		};
> +	};
> +
> +	gpio-hall-sensor {
> +		compatible = "gpio-keys";
> +
> +		label = "GPIO Hall Effect Sensor";
> +
> +		event-hall-sensor {
> +			label = "Hall Effect Sensor";
> +			gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
> +			linux,input-type = <EV_SW>;
> +			linux,code = <SW_LID>;
> +			linux,can-disable;
> +		};
> +	};
> +
> +	gpio-keys {

No need to have two nodes for gpio-keys. Combine them.

> +		compatible = "gpio-keys";
> +
> +		key-volume-up {
> +			label = "Volume Up";



Best regards,
Krzysztof