Re: [PATCH] Revert "ARM: dts: rockchip: restyle emac nodes"
From: Andy Yan
Date: Thu Dec 21 2023 - 03:29:24 EST
Hi Johan,
On 12/20/23 19:58, Johan Jonker wrote:
On 12/20/23 11:33, Andy Yan wrote:
From: Andy Yan <andy.yan@xxxxxxxxxxxxxx>
When try to run rk3036 kylin board with mainline,
I found the emac ethernet probe failed:
[ 2.324583] loop: module loaded
[ 2.328435] SPI driver spidev has no spi_device_id for rockchip,spidev
[ 2.338688] tun: Universal TUN/TAP device driver, 1.6
[ 2.345397] rockchip_emac 10200000.ethernet: no regulator found
[ 2.351892] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
[ 2.359331] rockchip_emac 10200000.ethernet: IRQ is 43
[ 2.364719] rockchip_emac 10200000.ethernet: MAC address is now e6:58:d6:ec:d9:7c
[ 2.396993] mdio_bus Synopsys MII Bus: mdio has invalid PHY address
[ 2.403306] mdio_bus Synopsys MII Bus: scan phy mdio at address 0
[ 2.508656] rockchip_emac 10200000.ethernet: of_phy_connect() failed
[ 2.516334] rockchip_emac 10200000.ethernet: failed to probe arc emac (-19)
This reverts commit 1dabb74971b3 ("ARM: dts: rockchip: restyle emac nodes")
make emac on rk3036 kylin board probe right again:
[ 1.920385] CAN device driver interface
[ 1.925499] rockchip_emac 10200000.ethernet: no regulator found
[ 1.932535] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
[ 1.940735] rockchip_emac 10200000.ethernet: IRQ is 42
[ 1.946743] rockchip_emac 10200000.ethernet: MAC address is now 96:7d:4f:0a:69:b3
[ 2.581340] rockchip_emac 10200000.ethernet: connected to Generic PHY phy with id 0xffffc816
[ 2.592560] e1000e: Intel(R) PRO/1000 Network Driver
[ 2.598136] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
Fixes: 1dabb74971b3 ("ARM: dts: rockchip: restyle emac nodes")
Signed-off-by: Andy Yan <andy.yan@xxxxxxxxxxxxxx>
---
arch/arm/boot/dts/rockchip/rk3036-evb.dts | 16 ++++++----------
arch/arm/boot/dts/rockchip/rk3036-kylin.dts | 16 ++++++----------
arch/arm/boot/dts/rockchip/rk3036.dtsi | 2 ++
.../boot/dts/rockchip/rk3066a-marsboard.dts | 17 +++++++----------
.../boot/dts/rockchip/rk3066a-rayeager.dts | 15 +++++----------
.../boot/dts/rockchip/rk3188-radxarock.dts | 19 ++++++++-----------
arch/arm/boot/dts/rockchip/rk3xxx.dtsi | 2 ++
7 files changed, 36 insertions(+), 51 deletions(-)
diff --git a/arch/arm/boot/dts/rockchip/rk3036-evb.dts b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
index becdc0b664bf..94216f870b57 100644
--- a/arch/arm/boot/dts/rockchip/rk3036-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
@@ -15,20 +15,16 @@ memory@60000000 {
};
&emac {
- phy = <&phy0>;
- phy-reset-duration = <10>; /* millisecond */
- phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
pinctrl-names = "default";
pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
- status = "okay";
+ phy = <&phy0>;
+ phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+ phy-reset-duration = <10>; /* millisecond */
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
+ status = "okay";
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
};
Sorry, didn't have the hardware when changing that binding.
A little bit background info:
The rk3036 TRM states:
Management Interface (MDIO) state machine for easy real-time communication with the
PHY
A revert of the DT must also match a binding. But...
Bindings must describe the hardware as close as possible.
So when the phy is called over the mdio we must add phy as part of a mdio node.(Is that correct? Ask a expert!)
Somehow the old emac driver doesn't support this sub node setup.
First request would be have a look to make the driver work as it should.
Because I lack of knowledge about net driver, I am not sure if the mdio is mandatory.
I post this revert also want to have some suggestion from the net expert.
From some grep:
emac_rockchip is based on arc-emac, but the example of arc_emac does not have a mdio node[0]
thera are also other platforms use the same way[1]
[0] Documentation/devicetree/bindings/net/arc_emac.txt
[1]arch/arm/boot/dts/hisilicon/hisi-x5hd2-dkb.dts
Johan
};
diff --git a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
index 67e1e04139e7..e817eba8c622 100644
--- a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
@@ -80,20 +80,16 @@ &acodec {
};
&emac {
- phy = <&phy0>;
- phy-reset-duration = <10>; /* millisecond */
- phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
pinctrl-names = "default";
pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
- status = "okay";
+ phy = <&phy0>;
+ phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+ phy-reset-duration = <10>; /* millisecond */
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
+ status = "okay";
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
};
};
diff --git a/arch/arm/boot/dts/rockchip/rk3036.dtsi b/arch/arm/boot/dts/rockchip/rk3036.dtsi
index 78686fc72ce6..e240b89b0b35 100644
--- a/arch/arm/boot/dts/rockchip/rk3036.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3036.dtsi
@@ -228,6 +228,8 @@ emac: ethernet@10200000 {
compatible = "rockchip,rk3036-emac";
reg = <0x10200000 0x4000>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
rockchip,grf = <&grf>;
clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
clock-names = "hclk", "macref", "macclk";
diff --git a/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
index f6e8d49a02ef..e3d6f0e81330 100644
--- a/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
@@ -150,21 +150,18 @@ vcc28_cif: regulator@12 {
#include "../tps65910.dtsi"
&emac {
+ status = "okay";
+
phy = <&phy0>;
phy-supply = <&vcc_rmii>;
+
pinctrl-names = "default";
pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- phy0: ethernet-phy@0 {
- reg = <0>;
- interrupt-parent = <&gpio1>;
- interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
};
};
diff --git a/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
index 29d8e5bf88f5..096616324c2d 100644
--- a/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
@@ -142,20 +142,15 @@ &cpu1 {
};
&emac {
- phy = <&phy0>;
- phy-supply = <&vcc_rmii>;
pinctrl-names = "default";
pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
+ phy = <&phy0>;
+ phy-supply = <&vcc_rmii>;
status = "okay";
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
};
};
diff --git a/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
index 118deacd38c4..239d2ec37fdc 100644
--- a/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
+++ b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
@@ -126,21 +126,18 @@ vsys: vsys-regulator {
};
&emac {
- phy = <&phy0>;
- phy-supply = <&vcc_rmii>;
+ status = "okay";
+
pinctrl-names = "default";
pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
- status = "okay";
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
+ phy = <&phy0>;
+ phy-supply = <&vcc_rmii>;
- phy0: ethernet-phy@0 {
- reg = <0>;
- interrupt-parent = <&gpio3>;
- interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
};
};
diff --git a/arch/arm/boot/dts/rockchip/rk3xxx.dtsi b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
index cb4e42ede56a..17e89d30de78 100644
--- a/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
@@ -193,6 +193,8 @@ emac: ethernet@10204000 {
compatible = "snps,arc-emac";
reg = <0x10204000 0x3c>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
rockchip,grf = <&grf>;