Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc

[Tanmay Shah]

On 1/3/24 11:54 AM, Mathieu Poirier wrote:
> Hi Tanmay,
>
> On Fri, Dec 15, 2023 at 03:57:24PM -0800, Tanmay Shah wrote:
> > Add properties as per new bindings in zynqmp remoteproc node
> > to represent TCM address and size.
> > 
> > This patch also adds alternative remoteproc node to represent
> > remoteproc cluster in split mode. By default lockstep mode is
> > enabled and users should disable it before using split mode
> > dts. Both device-tree nodes can't be used simultaneously one
> > of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> > remoteproc split mode dts node is enabled and lockstep mode
> > dts is disabled.
> > 
> > Signed-off-by: Tanmay Shah <tanmay.shah@xxxxxxx>
> > ---
> >  .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts  |  8 +++
> >  arch/arm64/boot/dts/xilinx/zynqmp.dtsi        | 60 +++++++++++++++++--
> >  2 files changed, 63 insertions(+), 5 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > index c8f71a1aec89..495ca94b45db 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > @@ -14,6 +14,14 @@ / {
> >  	compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> >  };
> >  
> > +&rproc_split {
> > +	status = "okay";
> > +};
> > +
> > +&rproc_lockstep {
> > +	status = "disabled";
> > +};
> > +
> >  &eeprom {
> >  	#address-cells = <1>;
> >  	#size-cells = <1>;
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > index b61fc99cd911..602e6aba7ac5 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> >  		ranges;
> >  	};
> >  
> > -	remoteproc {
> > +	rproc_lockstep: remoteproc@ffe00000 {
> >  		compatible = "xlnx,zynqmp-r5fss";
> >  		xlnx,cluster-mode = <1>;
> >  
> > -		r5f-0 {
> > +		#address-cells = <2>;
> > +		#size-cells = <2>;
> > +
> > +		ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> > +			 <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> > +			 <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > +			 <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
>
> As far as I can tell, in lockstep mode the last two entries are not needed.
> This is also contrasting with that is in the bindings, which is quite confusing.

Hi Mathieu,

Yes I agree. I think it should be same as of bindings example.

However, I will have to test and make sure no impact on driver. I will fix it in next revision.

Meanwhile, are you going to review driver changes as well or do you want to wait for next revision ?

Tanmay


> > +
> > +		r5f@0 {
> > +			compatible = "xlnx,zynqmp-r5f";
> > +			reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> > +			reg-names = "atcm", "btcm";
> > +			power-domains = <&zynqmp_firmware PD_RPU_0>,
> > +					<&zynqmp_firmware PD_R5_0_ATCM>,
> > +					<&zynqmp_firmware PD_R5_0_BTCM>;
> > +			memory-region = <&rproc_0_fw_image>;
> > +		};
> > +
> > +		r5f@1 {
> > +			compatible = "xlnx,zynqmp-r5f";
> > +			reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > +			reg-names = "atcm", "btcm";
> > +			power-domains = <&zynqmp_firmware PD_RPU_1>,
> > +					<&zynqmp_firmware PD_R5_1_ATCM>,
> > +					<&zynqmp_firmware PD_R5_1_BTCM>;
> > +			memory-region = <&rproc_1_fw_image>;
> > +		};
> > +	};
> > +
> > +	rproc_split: remoteproc-split@ffe00000 {
> > +		status = "disabled";
> > +		compatible = "xlnx,zynqmp-r5fss";
> > +		xlnx,cluster-mode = <0>;
> > +
> > +		#address-cells = <2>;
> > +		#size-cells = <2>;
> > +
> > +		ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> > +			 <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> > +			 <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > +			 <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > +
> > +		r5f@0 {
> >  			compatible = "xlnx,zynqmp-r5f";
> > -			power-domains = <&zynqmp_firmware PD_RPU_0>;
> > +			reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> > +			reg-names = "atcm", "btcm";
> > +			power-domains = <&zynqmp_firmware PD_RPU_0>,
> > +					<&zynqmp_firmware PD_R5_0_ATCM>,
> > +					<&zynqmp_firmware PD_R5_0_BTCM>;
> >  			memory-region = <&rproc_0_fw_image>;
> >  		};
> >  
> > -		r5f-1 {
> > +		r5f@1 {
> >  			compatible = "xlnx,zynqmp-r5f";
> > -			power-domains = <&zynqmp_firmware PD_RPU_1>;
> > +			reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > +			reg-names = "atcm", "btcm";
> > +			power-domains = <&zynqmp_firmware PD_RPU_1>,
> > +					<&zynqmp_firmware PD_R5_1_ATCM>,
> > +					<&zynqmp_firmware PD_R5_1_BTCM>;
> >  			memory-region = <&rproc_1_fw_image>;
> >  		};
> >  	};
> > -- 
> > 2.25.1
> >