[PATCH v4 12/12] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board

From: Frieder Schrempf
Date: Mon Jan 08 2024 - 03:52:58 EST

From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>

The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.

This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.

Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.

Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
---
Changes for v3:
* Address Shawn's review comments (thanks!)

Changes for v2:
* none
---
.../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 269 +++------
.../dts/freescale/imx8mm-kontron-osm-s.dtsi | 552 +++++++++++++++++-
2 files changed, 616 insertions(+), 205 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 12f786a72fbd5..efadfdff00af1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -25,8 +25,6 @@ osc_can: clock-osc-can {

leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_led>;

led1 {
label = "led1";
@@ -52,24 +50,12 @@ pwm-beeper {

reg_rst_eth2: regulator-rst-eth2 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usb_eth2>;
gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
regulator-name = "rst-usb-eth2";
};

- reg_usb1_vbus: regulator-usb1-vbus {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
- gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-name = "usb1-vbus";
- };
-
reg_vdd_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-always-on;
@@ -80,9 +66,6 @@ reg_vdd_5v: regulator-5v {
};

&ecspi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
- cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
status = "okay";

can@0 {
@@ -103,9 +86,6 @@ can@0 {
};

&ecspi3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi3>;
- cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
status = "okay";

eeram@0 {
@@ -117,7 +97,7 @@ eeram@0 {

&fec1 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
+ pinctrl-0 = <&pinctrl_enet_rgmii>;
phy-connection-type = "rgmii-id";
phy-handle = <&ethphy>;
status = "okay";
@@ -136,27 +116,59 @@ ethphy: ethernet-phy@0 {
};
};

+/*
+ * Rename SoM signals according to board usage:
+ * GPIO_B_0 -> DIO1_OUT
+ * GPIO_B_1 -> DIO2_OUT
+ */
&gpio1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio1>;
- gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
- "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
+ gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+ "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+ "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "DIO1_OUT",
+ "DIO2_OUT", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+ "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+ "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+ "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+ "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+ "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+ "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+ "ETH_A_(R)(G)MII_RXD3";
};

-&gpio5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio5>;
- gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "";
+/*
+ * Rename SoM signals according to board usage:
+ * GPIO_B_2 -> DIO3_OUT
+ * GPIO_B_3 -> DIO4_OUT
+ */
+&gpio3 {
+ gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+ "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+ "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+ "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+ "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "DIO3_OUT",
+ "USB_B_EN", "DIO4_OUT", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+ "PCIe_WAKE#", "USB_A_EN";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ * GPIO_B_4 -> DIO1_IN
+ * GPIO_B_5 -> DIO2_IN
+ * GPIO_B_6 -> DIO3_IN
+ * GPIO_B_7 -> DIO4_IN
+ */
+&gpio4 {
+ gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+ "DIO1_IN", "BOOT_SEL0#", "BOOT_SEL1#", "",
+ "", "", "I2S_LRCLK", "I2S_BITCLK",
+ "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "DIO2_IN", "DIO3_IN",
+ "DIO4_IN", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+ "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+ "UART_A_RTS", "", "", "",
+ "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
};

&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";

usb-hub@2c {
@@ -169,27 +181,28 @@ usb-hub@2c {
};
};

-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
-};
-
&pwm2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm2>;
status = "okay";
};

+&reg_usb2_vbus {
+ status = "disabled";
+};
+
+&reg_usdhc2_vcc {
+ status = "disabled";
+};
+
+&reg_usdhc3_vcc {
+ status = "disabled";
+};
+
&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
uart-has-rtscts;
status = "okay";
};

&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
linux,rs485-enabled-at-boot-time;
uart-has-rtscts;
status = "okay";
@@ -197,8 +210,6 @@ &uart2 {

&usbotg1 {
dr_mode = "otg";
- disable-over-current;
- vbus-supply = <&reg_usb1_vbus>;
status = "okay";
};

@@ -209,6 +220,9 @@ &usbotg2 {
#size-cells = <0>;
status = "okay";

+ /* VBUS is controlled by the hub */
+ /delete-property/ vbus-supply;
+
usb1@1 {
compatible = "usb424,2514";
reg = <1>;
@@ -224,171 +238,20 @@ usbnet: ethernet@1 {
};

&usdhc2 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
vmmc-supply = <&reg_vdd_3v3>;
- vqmmc-supply = <&reg_nvcc_sd>;
- cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
status = "okay";
};

&iomuxc {
pinctrl_can: cangrp {
fsl,pins = <
- MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82
- MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82
- MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82
- MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19
- >;
- };
-
- pinctrl_ecspi3: ecspi3grp {
- fsl,pins = <
- MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82
- MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82
- MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82
- MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
- MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
- MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
- MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
- MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
- MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
- MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
- MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
- MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
- MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
- MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
- MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
- MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
- MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
- MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* PHY RST */
- >;
- };
-
- pinctrl_gpio_led: gpioledgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19
- MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
- MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
- >;
- };
-
- pinctrl_gpio1: gpio1grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
- MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
- MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19
- MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
- MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
- >;
- };
-
- pinctrl_gpio5: gpio5grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083
- MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083
- MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083
- >;
- };
-
- pinctrl_pwm2: pwm2grp {
- fsl,pins = <
- MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19
- >;
- };
-
- pinctrl_reg_usb1_vbus: regusb1vbusgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0
- MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0
- MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0
- MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0
- MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0
- MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0
- MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0
- >;
- };
-
- pinctrl_usb_eth2: usbeth2grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
- MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
- MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
+ MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */
>;
};

- pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ pinctrl_usb_hub: usbhubgrp {
fsl,pins = <
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
- MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
+ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */
>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 6b9058fc53332..663ae52b48526 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -3,6 +3,7 @@
* Copyright (C) 2022 Kontron Electronics GmbH
*/

+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "imx8mm.dtsi"

@@ -28,6 +29,73 @@ memory@40000000 {
chosen {
stdout-path = &uart3;
};
+
+ reg_vdd_carrier: regulator-vdd-carrier {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+ gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "VDD_CARRIER";
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+
+ regulator-state-disk {
+ regulator-off-in-suspend;
+ };
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+ enable-active-high;
+ gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "VBUS_USB1";
+ };
+
+ reg_usb2_vbus: regulator-usb2-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usb2_vbus>;
+ enable-active-high;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "VBUS_USB2";
+ };
+
+ reg_usdhc2_vcc: regulator-usdhc2-vcc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+ enable-active-high;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "VCC_SDIO_A";
+ };
+
+ reg_usdhc3_vcc: regulator-usdhc3-vcc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>;
+ enable-active-high;
+ gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "VCC_SDIO_B";
+ };
};

&A53_0 {
@@ -96,6 +164,79 @@ partition@1f0000 {
};
};

+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>, <&pinctrl_ecspi2_gpio>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio1>;
+ gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+ "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+ "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "GPIO_B_0",
+ "GPIO_B_1", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+ "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+ "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+ "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+ "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+ "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+ "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+ "ETH_A_(R)(G)MII_RXD3";
+};
+
+&gpio2 {
+ gpio-line-names = "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "SDIO_A_CD#", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+ "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
+ "SDIO_A_WP";
+};
+
+&gpio3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio3>;
+ gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+ "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+ "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+ "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+ "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_2",
+ "USB_B_EN", "GPIO_B_3", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+ "PCIe_WAKE#", "USB_A_EN";
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio4>;
+ gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+ "GPIO_B_4", "BOOT_SEL0#", "BOOT_SEL1#", "",
+ "", "", "I2S_LRCLK", "I2S_BITCLK",
+ "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "GPIO_B_5", "GPIO_B_6",
+ "GPIO_B_7", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+ "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+ "UART_A_RTS", "", "", "",
+ "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
+};
+
+&gpio5 {
+ gpio-line-names = "UART_B_TX", "SDIO_B_PWR_EN", "SDIO_B_WP", "PWM_2",
+ "PWM_1", "PWM_0", "", "",
+ "", "", "SPI_A_SCK", "SPI_A_SDO_(IO1)",
+ "SPI_A_SCK", "SPI_A_CS0#", "", "",
+ "I2C_A_SCL", "I2C_A_SDA", "I2C_B_SCL", "I2C_B_SDA",
+ "PCIe_SMCLK", "PCIe_SMDAT", "SPI_B_SCK", "SPI_B_SDO",
+ "SPI_B_SDI", "SPI_B_CS0#", "UART_CON_RX", "UART_CON_TX",
+ "UART_C_RX", "UART_C_TX";
+};
+
&i2c1 {
clock-frequency = <400000>;
pinctrl-names = "default";
@@ -222,12 +363,69 @@ rv3028: rtc@52 {
};
};

+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+};
+
&uart3 { /* console */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};

+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>;
+ vbus-supply = <&reg_usb1_vbus>;
+};
+
+&usbotg2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb2>;
+ vbus-supply = <&reg_usb2_vbus>;
+};
+
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
@@ -240,6 +438,26 @@ &usdhc1 {
status = "okay";
};

+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ vmmc-supply = <&reg_usdhc2_vcc>;
+ vqmmc-supply = <&reg_nvcc_sd>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+ vmmc-supply = <&reg_usdhc3_vcc>;
+ vqmmc-supply = <&reg_nvcc_sd>;
+ cd-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+};
+
&wdog1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
@@ -248,6 +466,12 @@ &wdog1 {
};

&iomuxc {
+ pinctrl_csi_mck: csimckgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 /* CAM_MCK */
+ >;
+ };
+
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
@@ -257,6 +481,106 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
>;
};

+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 /* SPI_A_SDI_(IO0) */
+ MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 /* SPI_A_SDO_(IO1) */
+ MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 /* SPI_A_SCK */
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 /* SPI_A_CS0# */
+ >;
+ };
+
+ pinctrl_ecspi2_gpio: ecspi2gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19 /* SPI_A_/WP_(IO2) */
+ MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19 /* SPI_A_/HOLD_(IO3) */
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82 /* SPI_B_SDI */
+ MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82 /* SPI_B_SDO */
+ MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82 /* SPI_B_SCK */
+ MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19 /* SPI_B_CS0# */
+ >;
+ };
+
+ pinctrl_enet_rgmii: enetrgmiigrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 /* ETH_A_(R)(G)MII_RXD3 */
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 /* ETH_A_(R)(G)MII_RXD2 */
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f /* ETH_A_(R)(G)MII_TX_CLK */
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 /* ETH_A_(R)(G)MII_RX_CLK */
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+ >;
+ };
+
+ pinctrl_enet_rmii: enetrmiigrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */
+ MX8MM_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x4000001f /* ETH_A_(S)(R)(G)MII_TXD2 */
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x56 /* ETH_A_(S)(R)(G)MII_TXD1 */
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x56 /* ETH_A_(S)(R)(G)MII_TXD0 */
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x56 /* ETH_A_(S)(R)(G)MII_RXD1 */
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x56 /* ETH_A_(S)(R)(G)MII_RXD0 */
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RX_ER 0x56 /* ETH_A_(R)(G)MII_RX_CLK */
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x56 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x56 /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+ >;
+ };
+
+ pinctrl_gpio1: gpio1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* GPIO_A_0 */
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* GPIO_A_1 */
+ MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* GPIO_A_2 */
+ MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 /* GPIO_A_3 */
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 /* GPIO_A_4 */
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 /* GPIO_A_5 */
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 /* GPIO_A_6 */
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 /* GPIO_A_7 */
+ MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 /* GPIO_B_0 */
+ MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19 /* GPIO_B_1 */
+ >;
+ };
+
+ pinctrl_gpio3: gpio3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 /* GPIO_C_5 */
+ MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x19 /* GPIO_C_4 */
+ MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6 0x19 /* GPIO_C_0 */
+ MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 /* GPIO_C_1 */
+ MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8 0x19 /* GPIO_C_2 */
+ MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* GPIO_C_3 */
+ MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x19 /* GPIO_B_2 */
+ MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x19 /* GPIO_B_3 */
+ >;
+ };
+
+ pinctrl_gpio4: gpio4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19 /* GPIO_C_7 */
+ MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x19 /* GPIO_B_4 */
+ MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x19 /* BOOT_SEL0# */
+ MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x19 /* BOOT_SEL1# */
+ MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x19 /* GPIO_B_5 */
+ MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x19 /* GPIO_B_6 */
+ MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x19 /* GPIO_B_7 */
+ MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19 /* GPIO_C_6 */
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000083
@@ -264,22 +588,149 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000083
>;
};

+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000083 /* I2C_A_SCL */
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000083 /* I2C_A_SDA */
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083 /* I2C_B_SCL */
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083 /* I2C_B_SDA */
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 /* PCIe_SMCLK and I2C_CAM_SCL/CSI_TX_P */
+ MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 /* PCIe_SMDAT and I2C_CAM_SDA/CSI_TX_N */
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19 /* PCIe_CLKREQ# */
+ MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x19 /* PCIe_A_PERST# */
+ MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x19 /* PCIe_WAKE# */
+ MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 /* PCIe_SM_ALERT */
+ >;
+ };
+
pinctrl_pmic: pmicgrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
>;
};

+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x19 /* PWM_0 */
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 /* PWM_1 */
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x19 /* PWM_2 */
+ >;
+ };
+
+ pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 /* USB_A_EN */
+ >;
+ };
+
+ pinctrl_reg_usb2_vbus: regusb2vbusgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 /* USB_B_EN */
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x19 /* SDIO_A_PWR_EN */
+ >;
+ };
+
+ pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */
+ >;
+ };
+
+ pinctrl_reg_vdd_carrier: regvddcarriergrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* CARRIER_PWR_EN */
+ >;
+ };
+
pinctrl_rtc: rtcgrp {
fsl,pins = <
MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19
>;
};

+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0 0xd6 /* I2S_A_DATA_IN */
+ MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0 0xd6 /* I2S_A_DATA_OUT */
+ MX8MM_IOMUXC_SAI1_RXD1_SAI1_RX_DATA1 0xd6 /* I2S_B_DATA_IN */
+ MX8MM_IOMUXC_SAI1_TXD1_SAI1_TX_DATA1 0xd6 /* I2S_B_DATA_OUT */
+ MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK 0xd6 /* I2S_MCLK */
+ MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC 0xd6 /* I2S_LRCLK */
+ MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK 0xd6 /* I2S_BITCLK */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 /* UART_A_RX */
+ MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 /* UART_A_TX */
+ MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 /* UART_A_CTS */
+ MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 /* UART_A_RTS */
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 /* UART_B_RX */
+ MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 /* UART_B_TX */
+ MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 /* UART_B_CTS */
+ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 /* UART_B_RTS */
+ >;
+ };
+
pinctrl_uart3: uart3grp {
fsl,pins = <
- MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
- MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 /* UART_CON_RX */
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 /* UART_CON_TX */
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x0 /* UART_C_RX */
+ MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x0 /* UART_C_TX */
+ >;
+ };
+
+ pinctrl_usb1: usb1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19 /* USB_A_OC# */
+ >;
+ };
+
+ pinctrl_usb2: usb2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC 0x19 /* USB_B_OC# */
>;
};

@@ -334,6 +785,103 @@ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
>;
};

+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 /* SDIO_A_CLK */
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 /* SDIO_A_CMD */
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 /* SDIO_A_D0 */
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 /* SDIO_A_D1 */
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 /* SDIO_A_D2 */
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 /* SDIO_A_D3 */
+ MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 /* SDIO_A_CLK */
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 /* SDIO_A_CMD */
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 /* SDIO_A_D0 */
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 /* SDIO_A_D1 */
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 /* SDIO_A_D2 */
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 /* SDIO_A_D3 */
+ MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 /* SDIO_A_CLK */
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 /* SDIO_A_CMD */
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 /* SDIO_A_D0 */
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 /* SDIO_A_D1 */
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 /* SDIO_A_D2 */
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 /* SDIO_A_D3 */
+ MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 /* SDIO_A_CD# */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x90 /* SDIO_B_CLK */
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x90 /* SDIO_B_CMD */
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x90 /* SDIO_B_D0 */
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x90 /* SDIO_B_D1 */
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x90 /* SDIO_B_D2 */
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x90 /* SDIO_B_D3 */
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x90 /* SDIO_B_D4 */
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x90 /* SDIO_B_D5 */
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x90 /* SDIO_B_D6 */
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x90 /* SDIO_B_D7 */
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x94 /* SDIO_B_CLK */
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x94 /* SDIO_B_CMD */
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x94 /* SDIO_B_D0 */
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x94 /* SDIO_B_D1 */
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x94 /* SDIO_B_D2 */
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x94 /* SDIO_B_D3 */
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x94 /* SDIO_B_D4 */
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x94 /* SDIO_B_D5 */
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x94 /* SDIO_B_D6 */
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x94 /* SDIO_B_D7 */
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x96 /* SDIO_B_CLK */
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x96 /* SDIO_B_CMD */
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x96 /* SDIO_B_D0 */
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x96 /* SDIO_B_D1 */
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x96 /* SDIO_B_D2 */
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x96 /* SDIO_B_D3 */
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x96 /* SDIO_B_D4 */
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x96 /* SDIO_B_D5 */
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x96 /* SDIO_B_D6 */
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x96 /* SDIO_B_D7 */
+ >;
+ };
+
+ pinctrl_usdhc3_gpio: usdhc3gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* SDIO_B_CD# */
+ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */
+ >;
+ };
+
pinctrl_wdog: wdoggrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
--
2.43.0