[PATCH] arm64: dts: ti: k3-am625-beagleplay: Use the builtin mdio bus

[Sjoerd Simons]

The beagleplay dts was using a bit-bang gpio mdio bus as a work-around
for errata i2329. However since commit d04807b80691 ("net: ethernet: ti:
davinci_mdio: Add workaround for errata i2329") the mdio driver itself
already takes care of this errata for effected silicon, which landed
well before the beagleplay dts. So i suspect the reason for the
workaround in upstream was simply due to copying the vendor dts.

Switch the dts to the ti,cpsw-mdio instead so it described the actual
hardware and is consistent with other AM625 based boards

Signed-off-by: Sjoerd Simons <sjoerd@xxxxxxxxxxxxx>

---

 .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 42 +++++++------------
 1 file changed, 16 insertions(+), 26 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
index eadbdd9ffe37..49fb21ba62b0 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -29,7 +29,6 @@ aliases {
 		i2c3 = &main_i2c3;
 		i2c4 = &wkup_i2c0;
 		i2c5 = &mcu_i2c0;
-		mdio-gpio0 = &mdio0;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
 		mmc2 = &sdhci2;
@@ -231,27 +230,6 @@ simple-audio-card,codec {
 		};
 	};
 
-	/* Workaround for errata i2329 - just use mdio bitbang */
-	mdio0: mdio {
-		compatible = "virtual,mdio-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mdio0_pins_default>;
-		gpios = <&main_gpio0 86 GPIO_ACTIVE_HIGH>, /* MDC */
-			<&main_gpio0 85 GPIO_ACTIVE_HIGH>; /* MDIO */
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpsw3g_phy0: ethernet-phy@0 {
-			reg = <0>;
-		};
-
-		cpsw3g_phy1: ethernet-phy@1 {
-			reg = <1>;
-			reset-gpios = <&main_gpio1 5 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <25>;
-			reset-deassert-us = <60000>; /* T2 */
-		};
-	};
 };
 
 &main_pmx0 {
@@ -312,8 +290,8 @@ AM62X_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
 
 	mdio0_pins_default: mdio0-default-pins {
 		pinctrl-single,pins = <
-			AM62X_IOPAD(0x0160, PIN_OUTPUT, 7) /* (AD24) MDIO0_MDC.GPIO0_86 */
-			AM62X_IOPAD(0x015c, PIN_INPUT, 7) /* (AB22) MDIO0_MDIO.GPIO0_85 */
+			AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
+			AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
 		>;
 	};
 
@@ -611,8 +589,20 @@ &cpsw_port2 {
 };
 
 &cpsw3g_mdio {
-	/* Workaround for errata i2329 - Use mdio bitbang */
-	status = "disabled";
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio0_pins_default>;
+
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	cpsw3g_phy1: ethernet-phy@1 {
+		reg = <1>;
+		reset-gpios = <&main_gpio1 5 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <25>;
+		reset-deassert-us = <60000>; /* T2 */
+	};
 };
 
 &main_gpio0 {
-- 
2.43.0