In BCMBCA SoC, there is only one cs and customer design also have to use strap for the bootrom to boot up properly. They can override it with dts in linux but I don't think any customer would do that.
On 1/24/2024 7:09 PM, William Zhang wrote:
Hi Miquel,
On 1/24/24 09:30, Miquel Raynal wrote:
Hi David,I am not sure if I understand you comments correctly but are you suggesting to put this whole nand controller node into each board dts? We have other ip block nodes like SPI, uart in this same soc dtsi file too. For all the bcmbca soc dtsi I am updating here(and its board design), we always use the strap to for ecc setting. So I thought it should be okay to put brcm,nand-ecc-use-strap in the default dtsi file. For any board that uses the raw nand nand-ecc property, the board dts can do so and override the brcm,nand-ecc-use-strap setting.
dregan@xxxxxxxxxxxx wrote on Tue, 23 Jan 2024 19:04:50 -0800:
From: William Zhang <william.zhang@xxxxxxxxxxxx>
Add support for Broadcom STB NAND controller in BCMBCA ARMv7 chip dts
files.
Signed-off-by: William Zhang <william.zhang@xxxxxxxxxxxx>
Reviewed-by: David Regan <dregan@xxxxxxxxxxxx>
---
Changes in v3: None
---
Changes in v2: None
---
arch/arm/boot/dts/broadcom/bcm47622.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm63138.dtsi | 10 +++++++++-
arch/arm/boot/dts/broadcom/bcm63148.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm63178.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm6756.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm6846.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm6855.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm6878.dtsi | 17 +++++++++++++++++
arch/arm/boot/dts/broadcom/bcm947622.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm963138.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm963138dvt.dts | 12 +++++-------
arch/arm/boot/dts/broadcom/bcm963148.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm963178.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm96756.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm96846.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm96855.dts | 4 ++++
arch/arm/boot/dts/broadcom/bcm96878.dts | 4 ++++
17 files changed, 165 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/broadcom/bcm47622.dtsi b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
index 7cd38de118c3..55ff18043d96 100644
--- a/arch/arm/boot/dts/broadcom/bcm47622.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
@@ -138,6 +138,23 @@ hsspi: spi@1000 {
status = "disabled";
};
+ nand_controller: nand-controller@1800 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+ reg = <0x1800 0x600>, <0x2000 0x10>;
+ reg-names = "nand", "nand-int-base";
+ brcm,nand-use-wp = <0>;
+ status = "disabled";
+
+ nandcs: nand@0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-on-flash-bbt;
+ brcm,nand-ecc-use-strap;
Describing the NAND chip in a SoC DTSI does not look relevant to me.
Even more if you add something like this nand-ecc-use-strap setting
which is very board dependent.
I read Miquel's comment as meaning that the nandcs aka the NAND chip/flash part description should be in the board .dts file, while the controller itself can remain in the .dtsi file with its status = "disabled" property.
Are there customer boards, that is non reference boards that might chose a different chip select number and/or not use the strap settings?
Attachment:
smime.p7s
Description: S/MIME Cryptographic Signature