Re: [PATCH 9/9] arm64: dts: ti: k3-am69-sk: Add overlay for IMX219

[Andrew Davis]

On 1/29/24 7:27 AM, Vaishnav Achath wrote:
> RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM69
> through the 22-pin CSI-RX connector.
>
> Same overlay can be used across AM68 SK, TDA4VM SK boards that have a
> 15/22-pin FFC connector. Also enable build testing and symbols for
> all the three platforms.
>
> Signed-off-by: Vaishnav Achath <vaishnav.a@xxxxxx>
> ---
>   arch/arm64/boot/dts/ti/Makefile               |   6 +
>   .../boot/dts/ti/k3-am69-sk-csi2-imx219.dtso   | 124 ++++++++++++++++++
>   2 files changed, 130 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/ti/k3-am69-sk-csi2-imx219.dtso
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 52c1dc910308..9fc8d68f7d26 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -80,6 +80,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
>   
>   # Boards with J784s4 SoC
>   dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am69-sk-csi2-imx219.dtbo
>   dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
>   
>   # Build time test only, enabled by CONFIG_OF_ALL_DTBS
> @@ -105,6 +106,8 @@ k3-am642-tqma64xxl-mbax4xxl-sdcard-dtbs := \
>   	k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-sdcard.dtbo
>   k3-am642-tqma64xxl-mbax4xxl-wlan-dtbs := \
>   	k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-wlan.dtbo
> +k3-am69-sk-csi2-imx219-dtbs := k3-am69-sk.dtb \
> +	k3-am69-sk-csi2-imx219.dtbo

You need to also add this "k3-am69-sk-csi2-imx219.dtb" to the list:

dtb- +=

below for it to actually get build tested.

>   k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \
>   	k3-j721e-evm-pcie0-ep.dtbo
>   k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
> @@ -130,5 +133,8 @@ DTC_FLAGS_k3-am62-lp-sk += -@
>   DTC_FLAGS_k3-am62a7-sk += -@
>   DTC_FLAGS_k3-am642-tqma64xxl-mbax4xxl += -@
>   DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
> +DTC_FLAGS_k3-am68-sk-base-board += -@
> +DTC_FLAGS_k3-am69-sk += -@
>   DTC_FLAGS_k3-j721e-common-proc-board += -@
>   DTC_FLAGS_k3-j721s2-common-proc-board += -@
> +DTC_FLAGS_k3-j721e-sk += -@
> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk-csi2-imx219.dtso b/arch/arm64/boot/dts/ti/k3-am69-sk-csi2-imx219.dtso
> new file mode 100644
> index 000000000000..4cd1d8d5004a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk-csi2-imx219.dtso
> @@ -0,0 +1,124 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/**
> + * DT Overlay for RPi Camera V2.1 (Sony IMX219) interfaced with CSI2 on AM68-SK board.
> + * https://datasheets.raspberrypi.org/camera/camera-v2-schematic.pdf
> + *
> + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-pinctrl.h"
> +
> +&{/} {
> +	clk_imx219_fixed: imx219-xclk {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <24000000>;
> +	};
> +};
> +
> +&csi_mux {
> +	idle-state = <1>;
> +};
> +
> +/* CAM0 I2C */
> +&cam0_i2c {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	imx219_0: imx219_0@10 {
> +		compatible = "sony,imx219";
> +		reg = <0x10>;
> +
> +		clocks = <&clk_imx219_fixed>;
> +		clock-names = "xclk";
> +
> +		port {
> +			csi2_cam0: endpoint {
> +				remote-endpoint = <&csi2rx0_in_sensor>;
> +				link-frequencies = /bits/ 64 <456000000>;
> +				clock-lanes = <0>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
> +};
> +
> +/* CAM1 I2C */
> +&cam1_i2c {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	imx219_1: imx219_1@10 {
> +		compatible = "sony,imx219";
> +		reg = <0x10>;
> +
> +		clocks = <&clk_imx219_fixed>;
> +		clock-names = "xclk";
> +
> +		port {
> +			csi2_cam1: endpoint {
> +				remote-endpoint = <&csi2rx1_in_sensor>;
> +				link-frequencies = /bits/ 64 <456000000>;
> +				clock-lanes = <0>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
> +};
> +
> +
> +&cdns_csi2rx0 {
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		csi0_port0: port@0 {
> +			reg = <0>;
> +			status = "okay";
> +
> +			csi2rx0_in_sensor: endpoint {
> +				remote-endpoint = <&csi2_cam0>;
> +				bus-type = <4>; /* CSI2 DPHY. */
> +				clock-lanes = <0>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
> +};
> +
> +&dphy0 {
> +	status = "okay";
> +};
> +
> +&ti_csi2rx0 {
> +	status = "okay";
> +};
> +
> +&cdns_csi2rx1 {
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		csi1_port0: port@0 {
> +			reg = <0>;
> +			status = "okay";
> +
> +			csi2rx1_in_sensor: endpoint {
> +				remote-endpoint = <&csi2_cam1>;
> +				bus-type = <4>; /* CSI2 DPHY. */
> +				clock-lanes = <0>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
> +};
> +
> +&dphy1 {
> +	status = "okay";
> +};
> +
> +&ti_csi2rx1 {
> +	status = "okay";
> +};
> \ No newline at end of file

checkpatch..

Andrew