[RFC PATCH v2 1/6] dt-bindings: pinctrl: starfive: Add JH8100 pinctrl
From: Alex Soo
Date: Tue Feb 20 2024 - 02:17:35 EST
Add documentation and header file for JH8100 pinctrl driver.
Signed-off-by: Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
---
.../pinctrl/starfive,jh8100-aon-pinctrl.yaml | 261 ++++++++++++++++++
.../starfive,jh8100-sys-east-pinctrl.yaml | 223 +++++++++++++++
.../starfive,jh8100-sys-gmac-pinctrl.yaml | 163 +++++++++++
.../starfive,jh8100-sys-west-pinctrl.yaml | 220 +++++++++++++++
.../pinctrl/starfive,jh8100-pinctrl.h | 103 +++++++
5 files changed, 970 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
create mode 100644 include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
new file mode 100644
index 000000000000..ada40deca993
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
@@ -0,0 +1,261 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-aon-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 AON (always-on) Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "aon" pinctrl domain.
+
+ The "aon" domain has a pin controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - GPIO pins which support external GPIO interrupts or external wake-up.
+ - syscon registers to configure device I/O reference voltage.
+
+ In the AON Pin Controller, the pins named PAD_RGPIO0 to PAD_GPIO15 can be
+ multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the AON domain can have their I/O go through the 16
+ "PAD_RGPIOs". This includes I2C, UART, watchdog, eMMC, SDIO0, XSPI etc.
+
+ All these peripherals can be connected to any of the 16 PAD_RGPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ _____________
+ | |
+ RGPIO0 --------------| |--- PAD_RGPIO0
+ RGPIO1 --------------| AON I/O MUX |--- PAD_RGPIO1
+ ... | | ...
+ I2C8 SDA interface --| |--- PAD_RGPIO15
+ | |
+ -------------
+
+ The AON Pin Controller provides syscon registers to configure
+
+ 1. reference voltage of
+ - eMMC I/O interface
+ supported voltage - 1.8V
+ - SDIO0 I/O interface
+ supported voltage - 3.3V, 1.8V
+ - PAD_RGPIO bank
+ - 16 PAD_RGPIOs (PAD_RGPIO0 to PAD_GPIO15)
+ - all devices attached to PAD_RGPIOs must use I/O voltage 3.3V.
+ - XSPI I/O interface
+ supported voltage level - 3.3V
+
+ Regulator supplies the device voltage, and each device has a corresponding syscon
+ register bit [1:0] that must be configured to indicate the device voltage level.
+
+ +--------+--------+-------------------+
+ | Bit[1] | Bit[0] | Reference Voltage |
+ +--------+--------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +--------+--------+-------------------+
+ | 0 | 1 | 2.5 V |
+ +--------+--------+-------------------+
+ | 1 | x | 1.8 V |
+ +--------+--------+-------------------+
+
+ 2. reference voltage and slew rate of GMAC0
+
+ Voltage level on GMAC0 interface is dependent on the PHY that it is pairing with. The
+ supported voltage levels are 3.3V, 2.5V, and 1.8V.
+
+ GMAC0 has 2 set of syscon registers -
+
+ 2.1 PAD_VREF_GMAC0_syscon - bit [1:0] must be configured to indicate the voltage level on
+ GMAC0 interface. The default setting is 3.3V.
+
+ +--------+--------+-----------------------------------+
+ | Bit[1] | Bit[0] | GMAC0 Interface Reference Voltage |
+ +--------+--------+-----------------------------------+
+ | 0 | 0 | 3.3V |
+ +--------+--------+-----------------------------------+
+ | 0 | 1 | 2.5V |
+ +--------+--------+-----------------------------------+
+ | 1 | x | 1.8V |
+ +--------+--------+-----------------------------------+
+
+ 2.2 PAD_GMAC0_<SIGNAL_NAME>_syscon - each GMAC0 pad has a corresponding syscon bit [0] set
+ to 0 by default. When GMAC0 mode is RGMII and voltage level is 2.5V, the bit [0] must be
+ set to 1.
+
+ +-------------+-----------------------+---------+
+ | GMAC0 Mode | GMAC0 Voltage Level | Bit[0] |
+ +-------------+-----------------------+---------+
+ | | 3.3V | 0 |
+ | |-----------------------+---------+
+ | RGMII | 2.5V | 1 |
+ | |-----------------------+---------+
+ | | 1.8V | 0 |
+ +-------------+-----------------------+---------+
+ | | 3.3V | 0 |
+ | |-----------------------+---------+
+ | RMII | 2.5V | 0 |
+ | |-----------------------+---------+
+ | | 1.8V | 0 |
+ +-------------+-----------------------+---------+
+
+ the bit [2] can be used to configure GMAC0 signal slew rate,
+
+ +--------+-----------+
+ | Bit[2] | Slew Rate |
+ +--------+-----------+
+ | 0 | Fast |
+ +--------+-----------+
+ | 1 | Slow |
+ +--------+-----------+
+
+ Under any circumstances, the syscon register's reference voltage setting must not be
+ lower than the actual device voltage, otherwise, the device I/O pads will get damaged.
+
+ Follow the guidelines below when configure reference voltage -
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - const: starfive,jh8100-aon-pinctrl
+ - const: syscon
+ - const: simple-mfd
+
+ reg:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ gpio-ranges:
+ maxItems: 1
+
+ wakeup-gpios:
+ maxItems: 1
+ description: GPIO pin to be used for waking up the system from sleep mode.
+
+ wakeup-source:
+ maxItems: 1
+ description: to indicate pinctrl has wakeup capability.
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_aon: pinctrl@1f300000 {
+ compatible = "starfive,jh8100-aon-pinctrl", "syscon", "simple-mfd";
+ reg = <0x0 0x1f300000 0x0 0x10000>;
+ resets = <&aoncrg 0>;
+ interrupts = <160>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_aon 0 0 16>;
+
+ i2c7_pins: i2c7-grp {
+ i2c7-scl-pins {
+ pinmux = <0x23265409>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ i2c7-sda-pins {
+ pinmux = <0x2427580a>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
new file mode 100644
index 000000000000..3ea336cb7563
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
@@ -0,0 +1,223 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_EAST Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_east" pinctrl domain.
+
+ The "sys_east" domain has a pin controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+ - syscon for device voltage reference.
+
+ In the SYS_EAST Pin Controller, the pins named PAD_GPIO0_E to PAD_GPIO47_E can
+ be multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the SYS_EAST domain can have their I/O go through the 48
+ "PAD_GPIOs". This includes CANs, I2Cs, I2Ss, SPIs, UARTs, PWMs, SMBUS0, SDIO1 etc.
+
+ All these peripherals can be connected to any of the 48 PAD_GPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ __________________
+ | |
+ GPIO0 ----------------------| |--- PAD_GPIO0_E
+ GPIO1 ----------------------| SYS_EAST I/O MUX |--- PAD_GPIO1_E
+ GPIO2 ----------------------| |--- PAD_GPIO2_E
+ ... | | ...
+ I2C0 Clock interface -------| |--- PAD_GPIO9_E
+ I2C0 Data interface -------| |--- PAD_GPIO10_E
+ ... | | ...
+ UART0 transmit interface ---| |--- PAD_GPIO20_E
+ UART0 receive interface ----| |--- PAD_GPIO21_E
+ ... | | ...
+ GPIO47 ---------------------| |--- PAD_GPIO47_E
+ | |
+ ------------------
+
+ Alternatively, the "PAD_GPIOs" can be multiplexed to other peripherals through
+ function selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function or peripheral signal of an iopad.
+ The function 1 and function 2 are other optional functions or peripheral signals
+ available to an iopad. The function selection can be carried out by writing the
+ function number to the iopad function select register.
+
+ The "sys_east" domain has 4 PAD_GPIO banks -
+ E0 - 16 PAD_GPIOs (PAD_GPIO0_E to PAD_GPIO15_E)
+ E1 - 16 PAD_GPIOs (PAD_GPIO16_E to PAD_GPIO31_E)
+ E2 - 8 PAD_GPIOs (PAD_GPIO32_E to PAD_GPIO39_E)
+ E3 - 8 PAD_GPIOs (PAD_GPIO40_E to PAD_GPIO47_E)
+
+ Each PAD_GPIO bank can be set to a voltage level 3.3V or 1.8V. All devices attached
+ to the PAD_GPIOs must use the same I/O voltage level as the bank voltage setting.
+ This allows user to select different I/O voltages for their devices. For instance,
+ the UART have 3.3V/1.8V requirement, the UART devices that use 1.8V are attached
+ to a PAD_GPIO bank which is configured to 1.8V.
+
+ Regulators supply voltages to the PAD_GPIO banks, and each PAD_GPIO bank has a corresponding
+ syscon bit [1:0] that must be configured to indicate its voltage level. The default setting
+ is 3.3V.
+
+ +--------+--------+-------------------+
+ | Bit[1] | Bit[0] | Reference Voltage |
+ +--------+--------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +--------+--------+-------------------+
+ | 1 | x | 1.8 V |
+ +--------+--------+-------------------+
+
+ Under any circumstances, the syscon register's reference voltage setting must not be
+ lower than the actual device voltage, otherwise, the device I/O pads will get damaged.
+
+ Follow the guidelines below when configure reference voltage -
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - const: starfive,jh8100-sys-pinctrl-east
+ - const: syscon
+ - const: simple-mfd
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ gpio-ranges:
+ maxItems: 1
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_east: pinctrl@122d0000 {
+ compatible = "starfive,jh8100-sys-pinctrl-east", "syscon", "simple-mfd";
+ reg = <0x0 0x122d0000 0x0 0x10000>;
+ clocks = <&syscrg_ne 153>;
+ resets = <&syscrg_ne 48>;
+ interrupts = <182>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_east 0 0 48>;
+
+ smbus0_pins: smbus0-grp {
+ smbus0-scl-pins {
+ pinmux = <0x1122480b>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ smbus0-sda-pins {
+ pinmux = <0x12234c0c>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
new file mode 100644
index 000000000000..879b096f61f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_GMAC Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_gmac" pinctrl domain.
+
+ The "sys_gmac" domain has a pin-controller which provides syscon registers to
+ configure device reference voltage and slew rate.
+
+ The SYS_GMAC Pin Controller does not have any PAD_GPIOs, therefore, it does not
+ support the GPIO pad I/O Multiplexing and interrupt handling.
+
+ The SYS_GMAC Pin Controller provides syscon registers to configure
+
+ 1. reference voltage of SDIO1
+
+ The supported voltage levels are 3.3V and 1.8V
+
+ The bit [1:0] must be configured to indicate the SDIO1 voltage level.
+
+ +--------+--------+--------------------------+
+ | Bit[1] | Bit[0] | SDIO1 Reference Voltage |
+ +--------+--------+--------------------------+
+ | 0 | 0 | 3.3 V |
+ +--------+--------+--------------------------+
+ | 1 | 0 | 1.8 V |
+ +--------+--------+--------------------------+
+
+ 2. reference voltage and slew rate of GMAC1
+
+ Voltage level on GMAC1 interface is dependent on the PHY that it is pairing with. The
+ supported voltage levels are 3.3V, 2.5V, and 1.8V.
+
+ GMAC1 has 2 set of syscon registers -
+
+ 2.1 PAD_VREF_GMAC1_syscon - bit [1:0] must be configured to indicate the voltage level on
+ GMAC1 interface. The default setting is 3.3V.
+
+ +--------+--------+-----------------------------------+
+ | Bit[1] | Bit[0] | GMAC1 Interface Reference Voltage |
+ +--------+--------+-----------------------------------+
+ | 0 | 0 | 3.3V |
+ +--------+--------+-----------------------------------+
+ | 0 | 1 | 2.5V |
+ +--------+--------+-----------------------------------+
+ | 1 | x | 1.8V |
+ +--------+--------+-----------------------------------+
+
+ 2.2 PAD_GMAC1_<SIGNAL_NAME>_syscon - each GMAC1 pad has a corresponding syscon bit [0] set
+ to 0 by default. When GMAC1 mode is RGMII and voltage level is 2.5V, the bit [0] must be
+ set to 1.
+
+ +-------------+-----------------------+---------+
+ | GMAC1 Mode | GMAC1 Voltage Level | Bit[0] |
+ +-------------+-----------------------+---------+
+ | | 3.3V | 0 |
+ | |-----------------------+---------+
+ | RGMII | 2.5V | 1 |
+ | |-----------------------+---------+
+ | | 1.8V | 0 |
+ +-------------+-----------------------+---------+
+ | | 3.3V | 0 |
+ | |-----------------------+---------+
+ | RMII | 2.5V | 0 |
+ | |-----------------------+---------+
+ | | 1.8V | 0 |
+ +-------------+-----------------------+---------+
+
+ the bit [2] can be used to configure the GMAC1 signal slew rate,
+
+ +--------+-----------+
+ | Bit[2] | Slew Rate |
+ +--------+-----------+
+ | 0 | Fast |
+ +--------+-----------+
+ | 1 | Slow |
+ +--------+-----------+
+
+ Under any circumstances, the syscon register's reference voltage setting must not be
+ lower than the actual voltage, otherwise, the device I/O pads will get damaged.
+
+ Follow the guidelines below when configure reference voltage -
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - const: starfive,jh8100-sys-pinctrl-gmac
+ - const: syscon
+ - const: simple-mfd
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_gmac: pinctrl@12770000 {
+ compatible = "starfive,jh8100-sys-pinctrl-gmac", "syscon", "simple-mfd";
+ reg = <0x0 0x12770000 0x0 0x10000>;
+ clocks = <&gmac_sdio_crg 16>;
+ resets = <&gmac_sdio_crg 3>;
+ };
+
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
new file mode 100644
index 000000000000..431dd540d32c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
@@ -0,0 +1,220 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_WEST Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_west" pinctrl domain.
+
+ The "sys_west" domain has a pin-controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+ - syscon for device voltage reference.
+
+ In the SYS_WEST Pin Controller, the pins named PAD_GPIO0_W to PAD_GPIO15_W can
+ be multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the SYS_WEST domain can have their I/O go through the 16
+ "PAD_GPIOs". This includes I2Cs, HD_AUDIO, HIFI4, SPIs, UARTs, SMBUS1 etc.
+
+ All these peripherals can be connected to any of the 16 PAD_GPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ __________________
+ | |
+ GPIO0 ----------------------| |--- PAD_GPIO0_W
+ GPIO1 ----------------------| SYS_WEST I/O MUX |--- PAD_GPIO1_W
+ GPIO2 ----------------------| |--- PAD_GPIO2_W
+ ... | | ...
+ HIFI4 JTAG TDO interface ---| |--- PAD_GPIO10_W
+ HIFI4 JTAG TDI interface ---| |--- PAD_GPIO11_W
+ SMBUS1 Data interface -----| |--- PAD_GPIO12_W
+ SMBUS1 Clock interface -----| |--- PAD_GPIO13_W
+ ... | | ...
+ GPIO14 ---------------------| |--- PAD_GPIO14_W
+ GPIO15 ---------------------| |--- PAD_GPIO15_W
+ | |
+ ------------------
+
+ Alternatively, the "PAD_GPIOs" can be multiplexed to other peripherals through
+ function selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function or peripheral signal of an iopad.
+ The function 1 and function 2 are other optional functions or peripheral signals
+ available to an iopad. The function selection can be carried out by writing the
+ function number to the iopad function select register.
+
+ The "sys_west" domain has one PAD_GPIO bank -
+ W0 - 16 PAD_GPIOs (PAD_GPIO0_W to PAD_GPIO15_W)
+
+ The PAD_GPIO bank can be set to voltage level 3.3V or 1.8V. All devices attached
+ to the PAD_GPIOs must use the same I/O voltage level as the bank voltage setting.
+ This allows user to select different I/O voltages for their devices. For instance,
+ the UART have 3.3V/1.8V requirement, the UART devices that use 1.8V are attached
+ to a PAD_GPIO bank which is configured to 1.8V.
+
+ Regulator supplies voltage to the PAD_GPIO bank, and the PAD_GPIO bank has a
+ corresponding syscon bit [1:0] that must be configured to indicate its voltage
+ level. The default voltage setting of each PAD_GPIO bank is 3.3V.
+
+ +--------+--------+-------------------+
+ | Bit[1] | Bit[0] | Reference Voltage |
+ +--------+--------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +--------+--------+-------------------+
+ | 1 | x | 1.8 V |
+ +--------+--------+-------------------+
+
+ Under any circumstances, the syscon register's reference voltage setting must not be
+ lower than the actual device voltage, otherwise, the device I/O pads will get damaged.
+
+ Follow the guidelines below when configure reference voltage -
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - const: starfive,jh8100-sys-pinctrl-west
+ - const: syscon
+ - const: simple-mfd
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ gpio-ranges:
+ maxItems: 1
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_west: pinctrl@123e0000 {
+ compatible = "starfive,jh8100-sys-pinctrl-west", "syscon", "simple-mfd";
+ reg = <0x0 0x123e0000 0x0 0x10000>;
+ clocks = <&syscrg_nw 6>;
+ resets = <&syscrg_nw 1>;
+ interrupts = <183>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_west 0 0 16>;
+
+ smbus1_pins: smbus1-grp {
+ smbus1-scl-pins {
+ pinmux = <0x1014300d>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ smbus1-sda-pins {
+ pinmux = <0x1115340c>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
new file mode 100644
index 000000000000..055bac7eb2a6
--- /dev/null
+++ b/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
@@ -0,0 +1,103 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2023-2024 StarFive Technology Co., Ltd.
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH8100_H__
+#define __DT_BINDINGS_PINCTRL_STARFIVE_JH8100_H__
+
+/* sys_iomux_west pins */
+#define PAD_GPIO0_W 0
+#define PAD_GPIO1_W 1
+#define PAD_GPIO2_W 2
+#define PAD_GPIO3_W 3
+#define PAD_GPIO4_W 4
+#define PAD_GPIO5_W 5
+#define PAD_GPIO6_W 6
+#define PAD_GPIO7_W 7
+#define PAD_GPIO8_W 8
+#define PAD_GPIO9_W 9
+#define PAD_GPIO10_W 10
+#define PAD_GPIO11_W 11
+#define PAD_GPIO12_W 12
+#define PAD_GPIO13_W 13
+#define PAD_GPIO14_W 14
+#define PAD_GPIO15_W 15
+
+/* sys_iomux_east pins */
+#define PAD_GPIO0_E 0
+#define PAD_GPIO1_E 1
+#define PAD_GPIO2_E 2
+#define PAD_GPIO3_E 3
+#define PAD_GPIO4_E 4
+#define PAD_GPIO5_E 5
+#define PAD_GPIO6_E 6
+#define PAD_GPIO7_E 7
+#define PAD_GPIO8_E 8
+#define PAD_GPIO9_E 9
+#define PAD_GPIO10_E 10
+#define PAD_GPIO11_E 11
+#define PAD_GPIO12_E 12
+#define PAD_GPIO13_E 13
+#define PAD_GPIO14_E 14
+#define PAD_GPIO15_E 15
+#define PAD_GPIO16_E 16
+#define PAD_GPIO17_E 17
+#define PAD_GPIO18_E 18
+#define PAD_GPIO19_E 19
+#define PAD_GPIO20_E 20
+#define PAD_GPIO21_E 21
+#define PAD_GPIO22_E 22
+#define PAD_GPIO23_E 23
+#define PAD_GPIO24_E 24
+#define PAD_GPIO25_E 25
+#define PAD_GPIO26_E 26
+#define PAD_GPIO27_E 27
+#define PAD_GPIO28_E 28
+#define PAD_GPIO29_E 29
+#define PAD_GPIO30_E 30
+#define PAD_GPIO31_E 31
+#define PAD_GPIO32_E 32
+#define PAD_GPIO33_E 33
+#define PAD_GPIO34_E 34
+#define PAD_GPIO35_E 35
+#define PAD_GPIO36_E 36
+#define PAD_GPIO37_E 37
+#define PAD_GPIO38_E 38
+#define PAD_GPIO39_E 39
+#define PAD_GPIO40_E 40
+#define PAD_GPIO41_E 41
+#define PAD_GPIO42_E 42
+#define PAD_GPIO43_E 43
+#define PAD_GPIO44_E 44
+#define PAD_GPIO45_E 45
+#define PAD_GPIO46_E 46
+#define PAD_GPIO47_E 47
+
+/* aon_iomux pins */
+#define PAD_RGPIO0 0
+#define PAD_RGPIO1 1
+#define PAD_RGPIO2 2
+#define PAD_RGPIO3 3
+#define PAD_RGPIO4 4
+#define PAD_RGPIO5 5
+#define PAD_RGPIO6 6
+#define PAD_RGPIO7 7
+#define PAD_RGPIO8 8
+#define PAD_RGPIO9 9
+#define PAD_RGPIO10 10
+#define PAD_RGPIO11 11
+#define PAD_RGPIO12 12
+#define PAD_RGPIO13 13
+#define PAD_RGPIO14 14
+#define PAD_RGPIO15 15
+
+#define GPOUT_LOW 0
+#define GPOUT_HIGH 1
+
+#define GPOEN_ENABLE 0
+#define GPOEN_DISABLE 1
+
+#define GPI_NONE 255
+
+#endif
--
2.43.0