Re: [PATCH v2 09/20] media: i2c: ov4689: Use runtime PM autosuspend

[Sakari Ailus]

Hi Mikhail,

On Mon, Jan 08, 2024 at 06:06:52PM +0300, Mikhail Rudenko wrote:
> Hi Sakari,
> 
> Thanks for the review!
> 
> On 2024-01-08 at 11:18 GMT, Sakari Ailus <sakari.ailus@xxxxxx> wrote:
> 
> > Hi Mikhail,
> >
> > On Mon, Dec 18, 2023 at 08:40:30PM +0300, Mikhail Rudenko wrote:
> >> Use runtime PM autosuspend to avoid powering off the sensor during
> >> fast stop-reconfigure-restart cycles.
> >>
> >> Signed-off-by: Mikhail Rudenko <mike.rudenko@xxxxxxxxx>
> >> ---
> >>  drivers/media/i2c/ov4689.c | 22 +++++++++++++++-------
> >>  1 file changed, 15 insertions(+), 7 deletions(-)
> >>
> >> diff --git a/drivers/media/i2c/ov4689.c b/drivers/media/i2c/ov4689.c
> >> index 5300e621ff90..64cc6d9e48cc 100644
> >> --- a/drivers/media/i2c/ov4689.c
> >> +++ b/drivers/media/i2c/ov4689.c
> >> @@ -407,26 +407,27 @@ static int ov4689_s_stream(struct v4l2_subdev *sd, int on)
> >>  					  ov4689->cur_mode->num_regs,
> >>  					  NULL);
> >>  		if (ret) {
> >> -			pm_runtime_put(dev);
> >> +			pm_runtime_put_sync(dev);
> >
> > Why are you switching to pm_runtime_put_sync() here? That isn't covered by
> > the commit message (nor I think should be done).
> 
> PM autosuspend conversion was suggested earlier by Laurent in his review
> of this series [1], and he adviced looking at how it was done for the
> imx290 driver. I followed along the lines of the corresponding patch
> [2].

There's no need to use the _sync() variant here. And at least it wouldn't
be related to autosuspend, were you to switch to that.

> 
> >>  			goto unlock_and_return;
> >>  		}
> >>
> >>  		ret = __v4l2_ctrl_handler_setup(&ov4689->ctrl_handler);
> >>  		if (ret) {
> >> -			pm_runtime_put(dev);
> >> +			pm_runtime_put_sync(dev);
> >>  			goto unlock_and_return;
> >>  		}
> >>
> >>  		ret = cci_write(ov4689->regmap, OV4689_REG_CTRL_MODE,
> >>  				OV4689_MODE_STREAMING, NULL);
> >>  		if (ret) {
> >> -			pm_runtime_put(dev);
> >> +			pm_runtime_put_sync(dev);
> >>  			goto unlock_and_return;
> >>  		}
> >>  	} else {
> >>  		cci_write(ov4689->regmap, OV4689_REG_CTRL_MODE,
> >>  			  OV4689_MODE_SW_STANDBY, NULL);
> >> -		pm_runtime_put(dev);
> >> +		pm_runtime_mark_last_busy(dev);
> >> +		pm_runtime_put_autosuspend(dev);
> >>  	}
> >>
> >>  unlock_and_return:
> >> @@ -606,7 +607,9 @@ static int ov4689_set_ctrl(struct v4l2_ctrl *ctrl)
> >>  		break;
> >>  	}
> >>
> >> -	pm_runtime_put(dev);
> >> +	pm_runtime_mark_last_busy(dev);
> >> +	pm_runtime_put_autosuspend(dev);
> >
> > Also note that with runtime PM autosuspend,  you have to use
> > pm_runtime_get_if_active() instead of pm_runtime_get_if_in_use().
> 
> Noted, will do so in v3.
> 
> >> +
> >>  	return ret;
> >>  }
> >>
> >> @@ -877,8 +880,10 @@ static int ov4689_probe(struct i2c_client *client)
> >>  	}
> >>
> >>  	pm_runtime_set_active(dev);
> >> +	pm_runtime_get_noresume(dev);
> >>  	pm_runtime_enable(dev);
> >> -	pm_runtime_idle(dev);
> >> +	pm_runtime_set_autosuspend_delay(dev, 1000);
> >> +	pm_runtime_use_autosuspend(dev);
> >>
> >>  	ret = v4l2_async_register_subdev_sensor(sd);
> >>  	if (ret) {
> >> @@ -886,11 +891,14 @@ static int ov4689_probe(struct i2c_client *client)
> >>  		goto err_clean_subdev_pm;
> >>  	}
> >>
> >> +	pm_runtime_mark_last_busy(dev);
> >> +	pm_runtime_put_autosuspend(dev);
> >> +
> >>  	return 0;
> >>
> >>  err_clean_subdev_pm:
> >>  	pm_runtime_disable(dev);
> >> -	pm_runtime_set_suspended(dev);
> >> +	pm_runtime_put_noidle(dev);
> >>  	v4l2_subdev_cleanup(sd);
> >>  err_clean_entity:
> >>  	media_entity_cleanup(&sd->entity);
> 
> [1] https://lore.kernel.org/all/20231211181935.GG27535@xxxxxxxxxxxxxxxxxxxxxxxxxx/
> [2] https://lore.kernel.org/all/20230116144454.1012-14-laurent.pinchart@xxxxxxxxxxxxxxxx/
> 

-- 
Regards,

Sakari Ailus