Re: [PATCH v2 2/3] arm64: dts: qcom: sm8650: add support for the SM8650-HDK board

[Bjorn Andersson]

On Mon, Mar 18, 2024 at 10:51:54AM +0100, Neil Armstrong wrote:
[..]
> diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
[..]
> +	vph_pwr: vph-pwr-regulator {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vreg_bob_3v3: regulator-vreg-bob-3v3 {

It would be nice if these nodes where sorted alphabetically.

> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_BOB_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		vin-supply = <&vph_pwr>;
> +	};
> +
> +	wcd939x: audio-codec {
> +		compatible = "qcom,wcd9395-codec", "qcom,wcd9390-codec";
> +
> +		pinctrl-0 = <&wcd_default>;
> +		pinctrl-names = "default";
> +
> +		qcom,micbias1-microvolt = <1800000>;
> +		qcom,micbias2-microvolt = <1800000>;
> +		qcom,micbias3-microvolt = <1800000>;
> +		qcom,micbias4-microvolt = <1800000>;
> +		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
> +		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> +		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> +		qcom,rx-device = <&wcd_rx>;
> +		qcom,tx-device = <&wcd_tx>;
> +
> +		reset-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
> +
> +		vdd-buck-supply = <&vreg_l15b_1p8>;
> +		vdd-rxtx-supply = <&vreg_l15b_1p8>;
> +		vdd-io-supply = <&vreg_l15b_1p8>;
> +		vdd-mic-bias-supply = <&vreg_bob1>;
> +
> +		#sound-dai-cells = <1>;
> +	};
> +};
[..]
> +&mdss_mdp {
> +	status = "okay";

On other platforms we left status = okay on the mdp child node, as it's
pretty rare that you want mdss okay, but mdp disabled...

> +};
> +
> +&pcie0 {
> +	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> +	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-0 = <&pcie0_default_state>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};
> +
> +&pcie0_phy {
> +	vdda-phy-supply = <&vreg_l1i_0p88>;
> +	vdda-pll-supply = <&vreg_l3i_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&pcie1 {
> +	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
> +	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-0 = <&pcie1_default_state>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};
> +
> +&pcie1_phy {
> +	vdda-phy-supply = <&vreg_l3e_0p9>;
> +	vdda-pll-supply = <&vreg_l3i_1p2>;
> +	vdda-qref-supply = <&vreg_l1i_0p88>;
> +
> +	status = "okay";
> +};
> +
> +&pcie_1_phy_aux_clk {
> +	clock-frequency = <1000>;

Is that so?

> +};
> +

Regards,
Bjorn