Re: [PATCH 01/25] clk: meson: a1: restrict an amount of 'hifi_pll' params

From: Jan Dakinevich
Date: Mon Mar 18 2024 - 18:36:30 EST




On 3/18/24 13:17, Jerome Brunet wrote:
>
> On Sun 17 Mar 2024 at 17:17, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
>
>> On 3/15/24 11:58, Jerome Brunet wrote:
>>>
>>> On Fri 15 Mar 2024 at 02:21, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
>>>
>>>> Existing values were insufficient to produce accurate clock for audio
>>>> devices. New values are safe and most suitable to produce 48000Hz sample
>>>> rate.
>>>
>>> The hifi pll is not about 48k only. I see no reason to restrict the PLL
>>> to a single setting.
>>>> You've provided no justification why the PLL driver can't reach the same
>>> setting for 48k. The setting below is just the crude part. the fine
>>> tuning is done done with the frac parameter so I doubt this provides a
>>> more accurate rate.
>>>
>>
>> You are right, it is not about 48k only. However, there are two issues.
>>
>> First, indeed, I could just extend the range of multipliers to 1..255.
>
> Why 1..255 ? This is not what I'm pointing out
>
> According to the datasheet - the range is 32 - 64, as currently
> set in the driver.
>

Could you point where in the doc the range 32..64 is documented?
Documentation that I have may be not so complete, but I don't see there
any mention about it.

Anyway, range 32..64 of multipliers is not enough to produce accurate
clock, and a need 128 for 48kHz.

> The change you have provided request a multipler of 128/5 = 25,6
> If you put assigned-rate = 614400000 in DT, I see no reason can find the
> same solution on its own.
>

The reasoning is following. I don't know why 32..64 range was declared
for this clock, and whether it would be safe to extend it and include
128, which is required for 48kHz. But I know, that multiplier=128 is
safe and works fine (together divider=5).

>> But I am unsure if hifi_pll is able to handle whole range of
>> mulptipliers. The value 128 is taken from Amlogic's branch, and I am
>> pretty sure that it works.
>
>>
>> Second, unfortunately frac parameter currently doesn't work. When frac
>> is used enabling of hifi_pll fails in meson_clk_pll_wait_lock(). I see
>> it when try to use 44100Hz and multipliers' range is set to 1..255. So,
>> support of other rates than 48k requires extra effort.
>
> Then your change is even more problematic because it certainly does not
> disable frac ... which you say is broken.
>
> That parameter should be removed with a proper comment explaining why
> you are disabling it. That type a limitation / known issue should be
> mentionned in your change.
>

Handling of frac should not be removed, it should be fixed to achieve
another rates. But that is not the goal of this commit.


>>
>>>>
>>>> Signed-off-by: Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>
>>>> ---
>>>> drivers/clk/meson/a1-pll.c | 8 ++++----
>>>> 1 file changed, 4 insertions(+), 4 deletions(-)
>>>>
>>>> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
>>>> index 4325e8a6a3ef..00e06d03445b 100644
>>>> --- a/drivers/clk/meson/a1-pll.c
>>>> +++ b/drivers/clk/meson/a1-pll.c
>>>> @@ -74,9 +74,9 @@ static struct clk_regmap fixed_pll = {
>>>> },
>>>> };
>>>>
>>>> -static const struct pll_mult_range hifi_pll_mult_range = {
>>>> - .min = 32,
>>>> - .max = 64,
>>>> +static const struct pll_params_table hifi_pll_params_table[] = {
>>>> + PLL_PARAMS(128, 5),
>>>> + { },
>>>> };
>>>>
>>>> static const struct reg_sequence hifi_init_regs[] = {
>>>> @@ -124,7 +124,7 @@ static struct clk_regmap hifi_pll = {
>>>> .shift = 6,
>>>> .width = 1,
>>>> },
>>>> - .range = &hifi_pll_mult_range,
>>>> + .table = hifi_pll_params_table,
>>>> .init_regs = hifi_init_regs,
>>>> .init_count = ARRAY_SIZE(hifi_init_regs),
>>>> },
>>>
>>>
>
>

--
Best regards
Jan Dakinevich