Re: [PATCH v11] ASoc: tas2783: Add tas2783 codec driver

[Pierre-Louis Bossart]

> +static bool tas2783_readable_register(struct device *dev,
> +	unsigned int reg)
> +{
> +	switch (reg) {
> +	/* Page 0 */
> +	case 0x8000 ... 0x807F:
> +		return true;
> +	default:
> +		return false;

so only the registers in 0x8000..807F are readable. That's the usual
non-SDCA vendor-specific areas ...


> +static const struct regmap_config tasdevice_regmap = {
> +	.reg_bits = 32,
> +	.val_bits = 8,
> +	.readable_reg = tas2783_readable_register,
> +	.volatile_reg = tas2783_volatile_register,
> +	.max_register = 0x44ffffff,

... but here you show support for a much larger register set in SDCA space.

I am having a hard-time believing that none of these SDCA registers are
readable?

> +static void tas2783_calibration(struct tasdevice_priv *tas_dev)
> +{
> +	efi_guid_t efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc,
> +			0x09, 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92);
> +	static efi_char16_t efi_name[] = L"CALI_DATA";
> +	struct calibration_data cali_data;
> +	unsigned int *tmp_val;
> +	unsigned int crc;
> +	efi_status_t status;
> +
> +	cali_data.total_sz = 0;
> +
> +	status = efi.get_variable(efi_name, &efi_guid, NULL,
> +		&cali_data.total_sz, NULL);
> +	if (status == EFI_BUFFER_TOO_SMALL
> +		&& cali_data.total_sz < TAS2783_MAX_CALIDATA_SIZE) {
> +		status = efi.get_variable(efi_name, &efi_guid, NULL,
> +			&cali_data.total_sz,
> +			cali_data.data);
> +		dev_dbg(tas_dev->dev, "%s: cali get %lx bytes result:%ld\n",
> +			__func__, cali_data.total_sz, status);
> +	}
> +	if (status != 0) {
> +		/* Failed got calibration data from EFI. */
> +		dev_dbg(tas_dev->dev, "No calibration data in UEFI.");
> +		return;
> +	}
> +
> +	tmp_val = (unsigned int *)cali_data.data;
> +
> +	/* Check Calibrated Data V1 */
> +	crc = crc32(~0, cali_data.data, TAS2783_CALIDATAV1_BYTE_SIZE) ^ ~0;
> +	if (crc == tmp_val[TAS2783_CALIDATAV1_CRC32_INDX]) {
> +		/* Date and time of when calibration was done. */
> +		tas2783_apply_calibv1(tas_dev, tmp_val);
> +		dev_dbg(tas_dev->dev, "V1: %ptTs",

Is this really needed/helpful?

> +			&tmp_val[TAS2783_CALIDATAV1_TIMESTAMP_INDX]);
> +		return;
> +	}
> +
> +	/* Check Calibrated Data V2 */
> +	if (tmp_val[0] == 2783) {
> +		const struct calibdatav2_info calib_info = {
> +			.number_of_devices = tmp_val[1],
> +			.crc32_indx = 3 + tmp_val[1] * 6,
> +			.byt_sz = 12 + tmp_val[1] * 24,
> +			.cali_data = &tmp_val[3]
> +		};
> +
> +		if (calib_info.number_of_devices > TAS2783_MAX_DEV_NUM ||
> +			calib_info.number_of_devices == 0) {
> +			dev_dbg(tas_dev->dev, "No dev in calibrated data V2.");

the log is not aligned with the first condition where you have too many
devices.

It's not clear why it's not an error.

> +			return;
> +		}
> +		crc = crc32(~0, cali_data.data, calib_info.byt_sz)
> +			^ ~0;
> +		if (crc == tmp_val[calib_info.crc32_indx]) {
> +			tas2783_apply_calibv2(tas_dev, &calib_info);
> +			dev_dbg(tas_dev->dev, "V2: %ptTs",

same, is this needed?
> +				&tmp_val[TAS2783_CALIDATAV2_TIMESTAMP_INDX]);
> +		} else {
> +			dev_dbg(tas_dev->dev,
> +				"V2: CRC 0x%08x not match 0x%08x\n",
> +				crc, tmp_val[calib_info.crc32_indx]);

is this not an error?

> +		}
> +	} else {
> +		dev_err(tas_dev->dev, "Non-2783 chip\n");
> +	}
> +}

the error level seem inconsistent and it's not clear why errors are ignored?