Re: [PATCH 04/25] clk: meson: a1: add the audio clock controller driver

From: Jan Dakinevich
Date: Sat Mar 23 2024 - 14:04:11 EST


Jerome, I have reworked my driver reusing axg-audio code as most as I
could and now I have one more question. Lets see on this definition from
axg-audio:

#define AUD_MST_MUX(_name, _reg, _flag) \
AUD_MUX(_name##_sel, _reg, 0x7, 24, _flag, \
mst_mux_parent_data, 0)

#define AUD_MST_MCLK_MUX(_name, _reg) \
AUD_MST_MUX(_name, _reg, CLK_MUX_ROUND_CLOSEST)

CLK_SET_RATE_PARENT is not set here. But why? It means, that topmost pll
clock will not be reconfigured at runtime to satisfy the rate that was
requested from axg-tdm.


On 3/19/24 11:30, Jerome Brunet wrote:
>
> On Tue 19 Mar 2024 at 04:47, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
>
>> Let's start from the end:
>>
>>> No - Looks to me you just have two clock controllers you are trying
>> force into one.
>>
>>> Again, this shows 2 devices. The one related to your 'map0' should
>> request AUD2_CLKID_AUDIOTOP as input and enable it right away.
>>
>> Most of fishy workarounds that you commented is caused the fact the mmio
>> of this clock controller is divided into two parts. Compare it with
>> axg-audio driver, things that was part of contigous memory region (like
>> pdm) here are moved to second region. Is this enough to make a guess
>> that these are two devices?
>
> I see obsolutely no reason to think it is a single device nor to add all the quirks
> you have the way you did. So yes, in that case, 2 zones, 2 devices.
>
>>
>> Concerning AUD2_CLKID_AUDIOTOP clock, as it turned out, it must be
>> enabled before enabling of clocks from second region too. That is
>> AUD2_CLKID_AUDIOTOP clock feeds both parts of this clock controller.
>>
>
> Yes. I understood the first time around and already commented on that.
>
>>
>> On 3/15/24 12:20, Jerome Brunet wrote:
>>>
>>> On Fri 15 Mar 2024 at 02:21, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
>>>
>>>> This controller provides clocks and reset functionality for audio
>>>> peripherals on Amlogic A1 SoC family.
>>>>
>>>> The driver is almost identical to 'axg-audio', however it would be better
>>>> to keep it separate due to following reasons:
>>>>
>>>> - significant amount of bits has another definition. I will bring there
>>>> a mess of new defines with A1_ suffixes.
>>>>
>>>> - registers of this controller are located in two separate regions. It
>>>> will give a lot of complications for 'axg-audio' to support this.
>>>>
>>>> Signed-off-by: Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>
>>>> ---
>>>> drivers/clk/meson/Kconfig | 13 +
>>>> drivers/clk/meson/Makefile | 1 +
>>>> drivers/clk/meson/a1-audio.c | 556 +++++++++++++++++++++++++++++++++++
>>>> drivers/clk/meson/a1-audio.h | 58 ++++
>>>> 4 files changed, 628 insertions(+)
>>>> create mode 100644 drivers/clk/meson/a1-audio.c
>>>> create mode 100644 drivers/clk/meson/a1-audio.h
>>>>
>>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>>> index d6a2fa5f7e88..80c4a18c83d2 100644
>>>> --- a/drivers/clk/meson/Kconfig
>>>> +++ b/drivers/clk/meson/Kconfig
>>>> @@ -133,6 +133,19 @@ config COMMON_CLK_A1_PERIPHERALS
>>>> device, A1 SoC Family. Say Y if you want A1 Peripherals clock
>>>> controller to work.
>>>>
>>>> +config COMMON_CLK_A1_AUDIO
>>>> + tristate "Amlogic A1 SoC Audio clock controller support"
>>>> + depends on ARM64
>>>> + select COMMON_CLK_MESON_REGMAP
>>>> + select COMMON_CLK_MESON_CLKC_UTILS
>>>> + select COMMON_CLK_MESON_PHASE
>>>> + select COMMON_CLK_MESON_SCLK_DIV
>>>> + select COMMON_CLK_MESON_AUDIO_RSTC
>>>> + help
>>>> + Support for the Audio clock controller on Amlogic A113L based
>>>> + device, A1 SoC Family. Say Y if you want A1 Audio clock controller
>>>> + to work.
>>>> +
>>>> config COMMON_CLK_G12A
>>>> tristate "G12 and SM1 SoC clock controllers support"
>>>> depends on ARM64
>>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>>> index 88d94921a4dc..4968fc7ad555 100644
>>>> --- a/drivers/clk/meson/Makefile
>>>> +++ b/drivers/clk/meson/Makefile
>>>> @@ -20,6 +20,7 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>>>> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>>>> obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>>>> obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
>>>> +obj-$(CONFIG_COMMON_CLK_A1_AUDIO) += a1-audio.o
>>>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>>>> obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>>>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
>>>> diff --git a/drivers/clk/meson/a1-audio.c b/drivers/clk/meson/a1-audio.c
>>>> new file mode 100644
>>>> index 000000000000..6039116c93ba
>>>> --- /dev/null
>>>> +++ b/drivers/clk/meson/a1-audio.c
>>>> @@ -0,0 +1,556 @@
>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>> +/*
>>>> + * Copyright (c) 2024, SaluteDevices. All Rights Reserved.
>>>> + *
>>>> + * Author: Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>
>>>> + */
>>>> +
>>>> +#include <linux/clk.h>
>>>> +#include <linux/clk-provider.h>
>>>> +#include <linux/init.h>
>>>> +#include <linux/of_device.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/regmap.h>
>>>> +#include <linux/reset.h>
>>>> +#include <linux/reset-controller.h>
>>>> +#include <linux/slab.h>
>>>> +
>>>> +#include "meson-clkc-utils.h"
>>>> +#include "meson-audio-rstc.h"
>>>> +#include "clk-regmap.h"
>>>> +#include "clk-phase.h"
>>>> +#include "sclk-div.h"
>>>> +#include "a1-audio.h"
>>>> +
>>>> +#define AUDIO_PDATA(_name) \
>>>> + ((const struct clk_parent_data[]) { { .hw = &(_name).hw } })
>>>
>>> Not a fan - yet another level of macro.
>>>
>>>> +
>>>> +#define AUDIO_MUX(_name, _reg, _mask, _shift, _pdata) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct clk_regmap_mux_data){ \
>>>> + .offset = AUDIO_REG_OFFSET(_reg), \
>>>> + .mask = (_mask), \
>>>> + .shift = (_shift), \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &clk_regmap_mux_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = ARRAY_SIZE(_pdata), \
>>>> + .flags = CLK_SET_RATE_PARENT, \
>>>> + }, \
>>>> +}
>>>> +
>>>> +#define AUDIO_DIV(_name, _reg, _shift, _width, _pdata) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct clk_regmap_div_data){ \
>>>> + .offset = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &clk_regmap_divider_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = 1, \
>>>> + .flags = CLK_SET_RATE_PARENT, \
>>>> + }, \
>>>> +}
>>>> +
>>>> +#define AUDIO_GATE(_name, _reg, _bit, _pdata) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct clk_regmap_gate_data){ \
>>>> + .offset = AUDIO_REG_OFFSET(_reg), \
>>>> + .bit_idx = (_bit), \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &clk_regmap_gate_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = 1, \
>>>> + .flags = CLK_SET_RATE_PARENT, \
>>>> + }, \
>>>> +}
>>>> +
>>>> +#define AUDIO_SCLK_DIV(_name, _reg, _div_shift, _div_width, \
>>>> + _hi_shift, _hi_width, _pdata, _set_rate_parent) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct meson_sclk_div_data) { \
>>>> + .div = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_div_shift), \
>>>> + .width = (_div_width), \
>>>> + }, \
>>>> + .hi = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_hi_shift), \
>>>> + .width = (_hi_width), \
>>>> + }, \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &meson_sclk_div_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = 1, \
>>>> + .flags = (_set_rate_parent) ? CLK_SET_RATE_PARENT : 0, \
>>>
>>> Does not help readeability. Just pass the flag as axg-audio does.
>>>
>>>> + }, \
>>>> +}
>>>> +
>>>> +#define AUDIO_TRIPHASE(_name, _reg, _width, _shift0, _shift1, _shift2, \
>>>> + _pdata) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct meson_clk_triphase_data) { \
>>>> + .ph0 = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift0), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + .ph1 = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift1), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + .ph2 = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift2), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &meson_clk_triphase_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = 1, \
>>>> + .flags = CLK_SET_RATE_PARENT | CLK_DUTY_CYCLE_PARENT, \
>>>> + }, \
>>>> +}
>>>> +
>>>> +#define AUDIO_SCLK_WS(_name, _reg, _width, _shift_ph, _shift_ws, \
>>>> + _pdata) \
>>>> +static struct clk_regmap _name = { \
>>>> + .map = AUDIO_REG_MAP(_reg), \
>>>> + .data = &(struct meson_sclk_ws_inv_data) { \
>>>> + .ph = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift_ph), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + .ws = { \
>>>> + .reg_off = AUDIO_REG_OFFSET(_reg), \
>>>> + .shift = (_shift_ws), \
>>>> + .width = (_width), \
>>>> + }, \
>>>> + }, \
>>>> + .hw.init = &(struct clk_init_data) { \
>>>> + .name = #_name, \
>>>> + .ops = &meson_sclk_ws_inv_ops, \
>>>> + .parent_data = (_pdata), \
>>>> + .num_parents = 1, \
>>>> + .flags = CLK_SET_RATE_PARENT | CLK_DUTY_CYCLE_PARENT, \
>>>> + }, \
>>>> +}
>>>
>>> All the above does essentially the same things as the macro of
>>> axg-audio, to some minor differences. Yet it is another set to maintain.
>>>
>>
>> Except one thing... Here I keep memory identifier to which this clock
>> belongs:
>>
>> .map = AUDIO_REG_MAP(_reg),
>>
>> It is workaround, but ->map the only common field in clk_regmap that
>> could be used for this purpose.
>>
>>
>>> I'd much prefer if you put the axg-audio macro in a header a re-used
>>> those. There would a single set to maintain. You may then specialize the
>>> included in the driver C file, to avoid redundant parameters
>>>
>>> Rework axg-audio to use clk_parent_data if you must, but not in the same
>>> series please.
>>>
>>>> +
>>>> +static const struct clk_parent_data a1_pclk_pdata[] = {
>>>> + { .fw_name = "pclk", },
>>>> +};
>>>> +
>>>> +AUDIO_GATE(audio_ddr_arb, AUDIO_CLK_GATE_EN0, 0, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_tdmin_a, AUDIO_CLK_GATE_EN0, 1, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_tdmin_b, AUDIO_CLK_GATE_EN0, 2, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_tdmin_lb, AUDIO_CLK_GATE_EN0, 3, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_loopback, AUDIO_CLK_GATE_EN0, 4, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_tdmout_a, AUDIO_CLK_GATE_EN0, 5, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_tdmout_b, AUDIO_CLK_GATE_EN0, 6, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_frddr_a, AUDIO_CLK_GATE_EN0, 7, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_frddr_b, AUDIO_CLK_GATE_EN0, 8, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_toddr_a, AUDIO_CLK_GATE_EN0, 9, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_toddr_b, AUDIO_CLK_GATE_EN0, 10, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_spdifin, AUDIO_CLK_GATE_EN0, 11, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_resample, AUDIO_CLK_GATE_EN0, 12, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_eqdrc, AUDIO_CLK_GATE_EN0, 13, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio_audiolocker, AUDIO_CLK_GATE_EN0, 14, a1_pclk_pdata);
>>> This is what I mean by redundant parameter ^
>>>
>>
>> Yep. I could define something like AUDIO_PCLK_GATE().
>>
>>>> +
>>>> +AUDIO_GATE(audio2_ddr_arb, AUDIO2_CLK_GATE_EN0, 0, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio2_pdm, AUDIO2_CLK_GATE_EN0, 1, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio2_tdmin_vad, AUDIO2_CLK_GATE_EN0, 2, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio2_toddr_vad, AUDIO2_CLK_GATE_EN0, 3, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio2_vad, AUDIO2_CLK_GATE_EN0, 4, a1_pclk_pdata);
>>>> +AUDIO_GATE(audio2_audiotop, AUDIO2_CLK_GATE_EN0, 7, a1_pclk_pdata);
>>>> +
>>>> +static const struct clk_parent_data a1_mst_pdata[] = {
>>>> + { .fw_name = "dds_in" },
>>>> + { .fw_name = "fclk_div2" },
>>>> + { .fw_name = "fclk_div3" },
>>>> + { .fw_name = "hifi_pll" },
>>>> + { .fw_name = "xtal" },
>>>> +};
>>>> +
>>>> +#define AUDIO_MST_MCLK(_name, _reg) \
>>>> + AUDIO_MUX(_name##_mux, (_reg), 0x7, 24, a1_mst_pdata); \
>>>> + AUDIO_DIV(_name##_div, (_reg), 0, 16, \
>>>> + AUDIO_PDATA(_name##_mux)); \
>>>> + AUDIO_GATE(_name, (_reg), 31, AUDIO_PDATA(_name##_div))
>>>> +
>>>> +AUDIO_MST_MCLK(audio_mst_a_mclk, AUDIO_MCLK_A_CTRL);
>>>> +AUDIO_MST_MCLK(audio_mst_b_mclk, AUDIO_MCLK_B_CTRL);
>>>> +AUDIO_MST_MCLK(audio_mst_c_mclk, AUDIO_MCLK_C_CTRL);
>>>> +AUDIO_MST_MCLK(audio_mst_d_mclk, AUDIO_MCLK_D_CTRL);
>>>> +AUDIO_MST_MCLK(audio_spdifin_clk, AUDIO_CLK_SPDIFIN_CTRL);
>>>> +AUDIO_MST_MCLK(audio_eqdrc_clk, AUDIO_CLK_EQDRC_CTRL);
>>>> +
>>>> +AUDIO_MUX(audio_resample_clk_mux, AUDIO_CLK_RESAMPLE_CTRL, 0xf, 24,
>>>> + a1_mst_pdata);
>>>> +AUDIO_DIV(audio_resample_clk_div, AUDIO_CLK_RESAMPLE_CTRL, 0, 8,
>>>> + AUDIO_PDATA(audio_resample_clk_mux));
>>>> +AUDIO_GATE(audio_resample_clk, AUDIO_CLK_RESAMPLE_CTRL, 31,
>>>> + AUDIO_PDATA(audio_resample_clk_div));
>>>> +
>>>> +AUDIO_MUX(audio_locker_in_clk_mux, AUDIO_CLK_LOCKER_CTRL, 0xf, 8,
>>>> + a1_mst_pdata);
>>>> +AUDIO_DIV(audio_locker_in_clk_div, AUDIO_CLK_LOCKER_CTRL, 0, 8,
>>>> + AUDIO_PDATA(audio_locker_in_clk_mux));
>>>> +AUDIO_GATE(audio_locker_in_clk, AUDIO_CLK_LOCKER_CTRL, 15,
>>>> + AUDIO_PDATA(audio_locker_in_clk_div));
>>>> +
>>>> +AUDIO_MUX(audio_locker_out_clk_mux, AUDIO_CLK_LOCKER_CTRL, 0xf, 24,
>>>> + a1_mst_pdata);
>>>> +AUDIO_DIV(audio_locker_out_clk_div, AUDIO_CLK_LOCKER_CTRL, 16, 8,
>>>> + AUDIO_PDATA(audio_locker_out_clk_mux));
>>>> +AUDIO_GATE(audio_locker_out_clk, AUDIO_CLK_LOCKER_CTRL, 31,
>>>> + AUDIO_PDATA(audio_locker_out_clk_div));
>>>> +
>>>> +AUDIO_MST_MCLK(audio2_vad_mclk, AUDIO2_MCLK_VAD_CTRL);
>>>> +AUDIO_MST_MCLK(audio2_vad_clk, AUDIO2_CLK_VAD_CTRL);
>>>> +AUDIO_MST_MCLK(audio2_pdm_dclk, AUDIO2_CLK_PDMIN_CTRL0);
>>>> +AUDIO_MST_MCLK(audio2_pdm_sysclk, AUDIO2_CLK_PDMIN_CTRL1);
>>>> +
>>>> +#define AUDIO_MST_SCLK(_name, _reg0, _reg1, _pdata) \
>>>> + AUDIO_GATE(_name##_pre_en, (_reg0), 31, (_pdata)); \
>>>> + AUDIO_SCLK_DIV(_name##_div, (_reg0), 20, 10, 0, 0, \
>>>> + AUDIO_PDATA(_name##_pre_en), true); \
>>>> + AUDIO_GATE(_name##_post_en, (_reg0), 30, \
>>>> + AUDIO_PDATA(_name##_div)); \
>>>> + AUDIO_TRIPHASE(_name, (_reg1), 1, 0, 2, 4, \
>>>> + AUDIO_PDATA(_name##_post_en))
>>>> +
>>>
>>> Again, I'm not a fan of this many levels of macro. I can live with it
>>> but certainly don't want the burden of reviewing and maintaining for
>>> clock driver. AXG / G12 and A1 are obviously closely related, so make it common.
>>>
>>>> +#define AUDIO_MST_LRCLK(_name, _reg0, _reg1, _pdata) \
>>>> + AUDIO_SCLK_DIV(_name##_div, (_reg0), 0, 10, 10, 10, \
>>>> + (_pdata), false); \
>>>> + AUDIO_TRIPHASE(_name, (_reg1), 1, 1, 3, 5, \
>>>> + AUDIO_PDATA(_name##_div))
>>>> +
>>>> +AUDIO_MST_SCLK(audio_mst_a_sclk, AUDIO_MST_A_SCLK_CTRL0, AUDIO_MST_A_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_a_mclk));
>>>> +AUDIO_MST_SCLK(audio_mst_b_sclk, AUDIO_MST_B_SCLK_CTRL0, AUDIO_MST_B_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_b_mclk));
>>>> +AUDIO_MST_SCLK(audio_mst_c_sclk, AUDIO_MST_C_SCLK_CTRL0, AUDIO_MST_C_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_c_mclk));
>>>> +AUDIO_MST_SCLK(audio_mst_d_sclk, AUDIO_MST_D_SCLK_CTRL0, AUDIO_MST_D_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_d_mclk));
>>>> +
>>>> +AUDIO_MST_LRCLK(audio_mst_a_lrclk, AUDIO_MST_A_SCLK_CTRL0, AUDIO_MST_A_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_a_sclk_post_en));
>>>> +AUDIO_MST_LRCLK(audio_mst_b_lrclk, AUDIO_MST_B_SCLK_CTRL0, AUDIO_MST_B_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_b_sclk_post_en));
>>>> +AUDIO_MST_LRCLK(audio_mst_c_lrclk, AUDIO_MST_C_SCLK_CTRL0, AUDIO_MST_C_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_c_sclk_post_en));
>>>> +AUDIO_MST_LRCLK(audio_mst_d_lrclk, AUDIO_MST_D_SCLK_CTRL0, AUDIO_MST_D_SCLK_CTRL1,
>>>> + AUDIO_PDATA(audio_mst_d_sclk_post_en));
>>>> +
>>>> +static const struct clk_parent_data a1_mst_sclk_pdata[] = {
>>>> + { .hw = &audio_mst_a_sclk.hw },
>>>> + { .hw = &audio_mst_b_sclk.hw },
>>>> + { .hw = &audio_mst_c_sclk.hw },
>>>> + { .hw = &audio_mst_d_sclk.hw },
>>>> + { .fw_name = "slv_sclk0" },
>>>> + { .fw_name = "slv_sclk1" },
>>>> + { .fw_name = "slv_sclk2" },
>>>> + { .fw_name = "slv_sclk3" },
>>>> + { .fw_name = "slv_sclk4" },
>>>> + { .fw_name = "slv_sclk5" },
>>>> + { .fw_name = "slv_sclk6" },
>>>> + { .fw_name = "slv_sclk7" },
>>>> + { .fw_name = "slv_sclk8" },
>>>> + { .fw_name = "slv_sclk9" },
>>>> +};
>>>> +
>>>> +static const struct clk_parent_data a1_mst_lrclk_pdata[] = {
>>>> + { .hw = &audio_mst_a_lrclk.hw },
>>>> + { .hw = &audio_mst_b_lrclk.hw },
>>>> + { .hw = &audio_mst_c_lrclk.hw },
>>>> + { .hw = &audio_mst_d_lrclk.hw },
>>>> + { .fw_name = "slv_lrclk0" },
>>>> + { .fw_name = "slv_lrclk1" },
>>>> + { .fw_name = "slv_lrclk2" },
>>>> + { .fw_name = "slv_lrclk3" },
>>>> + { .fw_name = "slv_lrclk4" },
>>>> + { .fw_name = "slv_lrclk5" },
>>>> + { .fw_name = "slv_lrclk6" },
>>>> + { .fw_name = "slv_lrclk7" },
>>>> + { .fw_name = "slv_lrclk8" },
>>>> + { .fw_name = "slv_lrclk9" },
>>>> +};
>>>> +
>>>> +#define AUDIO_TDM_SCLK(_name, _reg) \
>>>> + AUDIO_MUX(_name##_mux, (_reg), 0xf, 24, a1_mst_sclk_pdata); \
>>>> + AUDIO_GATE(_name##_pre_en, (_reg), 31, \
>>>> + AUDIO_PDATA(_name##_mux)); \
>>>> + AUDIO_GATE(_name##_post_en, (_reg), 30, \
>>>> + AUDIO_PDATA(_name##_pre_en)); \
>>>> + AUDIO_SCLK_WS(_name, (_reg), 1, 29, 28, \
>>>> + AUDIO_PDATA(_name##_post_en))
>>>> +
>>>> +#define AUDIO_TDM_LRCLK(_name, _reg) \
>>>> + AUDIO_MUX(_name, (_reg), 0xf, 20, a1_mst_lrclk_pdata)
>>>> +
>>>> +AUDIO_TDM_SCLK(audio_tdmin_a_sclk, AUDIO_CLK_TDMIN_A_CTRL);
>>>> +AUDIO_TDM_SCLK(audio_tdmin_b_sclk, AUDIO_CLK_TDMIN_B_CTRL);
>>>> +AUDIO_TDM_SCLK(audio_tdmin_lb_sclk, AUDIO_CLK_TDMIN_LB_CTRL);
>>>> +AUDIO_TDM_SCLK(audio_tdmout_a_sclk, AUDIO_CLK_TDMOUT_A_CTRL);
>>>> +AUDIO_TDM_SCLK(audio_tdmout_b_sclk, AUDIO_CLK_TDMOUT_B_CTRL);
>>>> +
>>>> +AUDIO_TDM_LRCLK(audio_tdmin_a_lrclk, AUDIO_CLK_TDMIN_A_CTRL);
>>>> +AUDIO_TDM_LRCLK(audio_tdmin_b_lrclk, AUDIO_CLK_TDMIN_B_CTRL);
>>>> +AUDIO_TDM_LRCLK(audio_tdmin_lb_lrclk, AUDIO_CLK_TDMIN_LB_CTRL);
>>>> +AUDIO_TDM_LRCLK(audio_tdmout_a_lrclk, AUDIO_CLK_TDMOUT_A_CTRL);
>>>> +AUDIO_TDM_LRCLK(audio_tdmout_b_lrclk, AUDIO_CLK_TDMOUT_B_CTRL);
>>>> +
>>>> +static struct clk_hw *a1_audio_hw_clks[] = {
>>>> + [AUD_CLKID_DDR_ARB] = &audio_ddr_arb.hw,
>>>> + [AUD_CLKID_TDMIN_A] = &audio_tdmin_a.hw,
>>>> + [AUD_CLKID_TDMIN_B] = &audio_tdmin_b.hw,
>>>> + [AUD_CLKID_TDMIN_LB] = &audio_tdmin_lb.hw,
>>>> + [AUD_CLKID_LOOPBACK] = &audio_loopback.hw,
>>>> + [AUD_CLKID_TDMOUT_A] = &audio_tdmout_a.hw,
>>>> + [AUD_CLKID_TDMOUT_B] = &audio_tdmout_b.hw,
>>>> + [AUD_CLKID_FRDDR_A] = &audio_frddr_a.hw,
>>>> + [AUD_CLKID_FRDDR_B] = &audio_frddr_b.hw,
>>>> + [AUD_CLKID_TODDR_A] = &audio_toddr_a.hw,
>>>> + [AUD_CLKID_TODDR_B] = &audio_toddr_b.hw,
>>>> + [AUD_CLKID_SPDIFIN] = &audio_spdifin.hw,
>>>> + [AUD_CLKID_RESAMPLE] = &audio_resample.hw,
>>>> + [AUD_CLKID_EQDRC] = &audio_eqdrc.hw,
>>>> + [AUD_CLKID_LOCKER] = &audio_audiolocker.hw,
>>>> + [AUD_CLKID_MST_A_MCLK_SEL] = &audio_mst_a_mclk_mux.hw,
>>>> + [AUD_CLKID_MST_A_MCLK_DIV] = &audio_mst_a_mclk_div.hw,
>>>> + [AUD_CLKID_MST_A_MCLK] = &audio_mst_a_mclk.hw,
>>>> + [AUD_CLKID_MST_B_MCLK_SEL] = &audio_mst_b_mclk_mux.hw,
>>>> + [AUD_CLKID_MST_B_MCLK_DIV] = &audio_mst_b_mclk_div.hw,
>>>> + [AUD_CLKID_MST_B_MCLK] = &audio_mst_b_mclk.hw,
>>>> + [AUD_CLKID_MST_C_MCLK_SEL] = &audio_mst_c_mclk_mux.hw,
>>>> + [AUD_CLKID_MST_C_MCLK_DIV] = &audio_mst_c_mclk_div.hw,
>>>> + [AUD_CLKID_MST_C_MCLK] = &audio_mst_c_mclk.hw,
>>>> + [AUD_CLKID_MST_D_MCLK_SEL] = &audio_mst_d_mclk_mux.hw,
>>>> + [AUD_CLKID_MST_D_MCLK_DIV] = &audio_mst_d_mclk_div.hw,
>>>> + [AUD_CLKID_MST_D_MCLK] = &audio_mst_d_mclk.hw,
>>>> + [AUD_CLKID_RESAMPLE_CLK_SEL] = &audio_resample_clk_mux.hw,
>>>> + [AUD_CLKID_RESAMPLE_CLK_DIV] = &audio_resample_clk_div.hw,
>>>> + [AUD_CLKID_RESAMPLE_CLK] = &audio_resample_clk.hw,
>>>> + [AUD_CLKID_LOCKER_IN_CLK_SEL] = &audio_locker_in_clk_mux.hw,
>>>> + [AUD_CLKID_LOCKER_IN_CLK_DIV] = &audio_locker_in_clk_div.hw,
>>>> + [AUD_CLKID_LOCKER_IN_CLK] = &audio_locker_in_clk.hw,
>>>> + [AUD_CLKID_LOCKER_OUT_CLK_SEL] = &audio_locker_out_clk_mux.hw,
>>>> + [AUD_CLKID_LOCKER_OUT_CLK_DIV] = &audio_locker_out_clk_div.hw,
>>>> + [AUD_CLKID_LOCKER_OUT_CLK] = &audio_locker_out_clk.hw,
>>>> + [AUD_CLKID_SPDIFIN_CLK_SEL] = &audio_spdifin_clk_mux.hw,
>>>> + [AUD_CLKID_SPDIFIN_CLK_DIV] = &audio_spdifin_clk_div.hw,
>>>> + [AUD_CLKID_SPDIFIN_CLK] = &audio_spdifin_clk.hw,
>>>> + [AUD_CLKID_EQDRC_CLK_SEL] = &audio_eqdrc_clk_mux.hw,
>>>> + [AUD_CLKID_EQDRC_CLK_DIV] = &audio_eqdrc_clk_div.hw,
>>>> + [AUD_CLKID_EQDRC_CLK] = &audio_eqdrc_clk.hw,
>>>> + [AUD_CLKID_MST_A_SCLK_PRE_EN] = &audio_mst_a_sclk_pre_en.hw,
>>>> + [AUD_CLKID_MST_A_SCLK_DIV] = &audio_mst_a_sclk_div.hw,
>>>> + [AUD_CLKID_MST_A_SCLK_POST_EN] = &audio_mst_a_sclk_post_en.hw,
>>>> + [AUD_CLKID_MST_A_SCLK] = &audio_mst_a_sclk.hw,
>>>> + [AUD_CLKID_MST_B_SCLK_PRE_EN] = &audio_mst_b_sclk_pre_en.hw,
>>>> + [AUD_CLKID_MST_B_SCLK_DIV] = &audio_mst_b_sclk_div.hw,
>>>> + [AUD_CLKID_MST_B_SCLK_POST_EN] = &audio_mst_b_sclk_post_en.hw,
>>>> + [AUD_CLKID_MST_B_SCLK] = &audio_mst_b_sclk.hw,
>>>> + [AUD_CLKID_MST_C_SCLK_PRE_EN] = &audio_mst_c_sclk_pre_en.hw,
>>>> + [AUD_CLKID_MST_C_SCLK_DIV] = &audio_mst_c_sclk_div.hw,
>>>> + [AUD_CLKID_MST_C_SCLK_POST_EN] = &audio_mst_c_sclk_post_en.hw,
>>>> + [AUD_CLKID_MST_C_SCLK] = &audio_mst_c_sclk.hw,
>>>> + [AUD_CLKID_MST_D_SCLK_PRE_EN] = &audio_mst_d_sclk_pre_en.hw,
>>>> + [AUD_CLKID_MST_D_SCLK_DIV] = &audio_mst_d_sclk_div.hw,
>>>> + [AUD_CLKID_MST_D_SCLK_POST_EN] = &audio_mst_d_sclk_post_en.hw,
>>>> + [AUD_CLKID_MST_D_SCLK] = &audio_mst_d_sclk.hw,
>>>> + [AUD_CLKID_MST_A_LRCLK_DIV] = &audio_mst_a_lrclk_div.hw,
>>>> + [AUD_CLKID_MST_A_LRCLK] = &audio_mst_a_lrclk.hw,
>>>> + [AUD_CLKID_MST_B_LRCLK_DIV] = &audio_mst_b_lrclk_div.hw,
>>>> + [AUD_CLKID_MST_B_LRCLK] = &audio_mst_b_lrclk.hw,
>>>> + [AUD_CLKID_MST_C_LRCLK_DIV] = &audio_mst_c_lrclk_div.hw,
>>>> + [AUD_CLKID_MST_C_LRCLK] = &audio_mst_c_lrclk.hw,
>>>> + [AUD_CLKID_MST_D_LRCLK_DIV] = &audio_mst_d_lrclk_div.hw,
>>>> + [AUD_CLKID_MST_D_LRCLK] = &audio_mst_d_lrclk.hw,
>>>> + [AUD_CLKID_TDMIN_A_SCLK_SEL] = &audio_tdmin_a_sclk_mux.hw,
>>>> + [AUD_CLKID_TDMIN_A_SCLK_PRE_EN] = &audio_tdmin_a_sclk_pre_en.hw,
>>>> + [AUD_CLKID_TDMIN_A_SCLK_POST_EN] = &audio_tdmin_a_sclk_post_en.hw,
>>>> + [AUD_CLKID_TDMIN_A_SCLK] = &audio_tdmin_a_sclk.hw,
>>>> + [AUD_CLKID_TDMIN_A_LRCLK] = &audio_tdmin_a_lrclk.hw,
>>>> + [AUD_CLKID_TDMIN_B_SCLK_SEL] = &audio_tdmin_b_sclk_mux.hw,
>>>> + [AUD_CLKID_TDMIN_B_SCLK_PRE_EN] = &audio_tdmin_b_sclk_pre_en.hw,
>>>> + [AUD_CLKID_TDMIN_B_SCLK_POST_EN] = &audio_tdmin_b_sclk_post_en.hw,
>>>> + [AUD_CLKID_TDMIN_B_SCLK] = &audio_tdmin_b_sclk.hw,
>>>> + [AUD_CLKID_TDMIN_B_LRCLK] = &audio_tdmin_b_lrclk.hw,
>>>> + [AUD_CLKID_TDMIN_LB_SCLK_SEL] = &audio_tdmin_lb_sclk_mux.hw,
>>>> + [AUD_CLKID_TDMIN_LB_SCLK_PRE_EN] = &audio_tdmin_lb_sclk_pre_en.hw,
>>>> + [AUD_CLKID_TDMIN_LB_SCLK_POST_EN] = &audio_tdmin_lb_sclk_post_en.hw,
>>>> + [AUD_CLKID_TDMIN_LB_SCLK] = &audio_tdmin_lb_sclk.hw,
>>>> + [AUD_CLKID_TDMIN_LB_LRCLK] = &audio_tdmin_lb_lrclk.hw,
>>>> + [AUD_CLKID_TDMOUT_A_SCLK_SEL] = &audio_tdmout_a_sclk_mux.hw,
>>>> + [AUD_CLKID_TDMOUT_A_SCLK_PRE_EN] = &audio_tdmout_a_sclk_pre_en.hw,
>>>> + [AUD_CLKID_TDMOUT_A_SCLK_POST_EN] = &audio_tdmout_a_sclk_post_en.hw,
>>>> + [AUD_CLKID_TDMOUT_A_SCLK] = &audio_tdmout_a_sclk.hw,
>>>> + [AUD_CLKID_TDMOUT_A_LRCLK] = &audio_tdmout_a_lrclk.hw,
>>>> + [AUD_CLKID_TDMOUT_B_SCLK_SEL] = &audio_tdmout_b_sclk_mux.hw,
>>>> + [AUD_CLKID_TDMOUT_B_SCLK_PRE_EN] = &audio_tdmout_b_sclk_pre_en.hw,
>>>> + [AUD_CLKID_TDMOUT_B_SCLK_POST_EN] = &audio_tdmout_b_sclk_post_en.hw,
>>>> + [AUD_CLKID_TDMOUT_B_SCLK] = &audio_tdmout_b_sclk.hw,
>>>> + [AUD_CLKID_TDMOUT_B_LRCLK] = &audio_tdmout_b_lrclk.hw,
>>>> +
>>>> + [AUD2_CLKID_DDR_ARB] = &audio2_ddr_arb.hw,
>>>> + [AUD2_CLKID_PDM] = &audio2_pdm.hw,
>>>> + [AUD2_CLKID_TDMIN_VAD] = &audio2_tdmin_vad.hw,
>>>> + [AUD2_CLKID_TODDR_VAD] = &audio2_toddr_vad.hw,
>>>> + [AUD2_CLKID_VAD] = &audio2_vad.hw,
>>>> + [AUD2_CLKID_AUDIOTOP] = &audio2_audiotop.hw,
>>>> + [AUD2_CLKID_VAD_MCLK_SEL] = &audio2_vad_mclk_mux.hw,
>>>> + [AUD2_CLKID_VAD_MCLK_DIV] = &audio2_vad_mclk_div.hw,
>>>> + [AUD2_CLKID_VAD_MCLK] = &audio2_vad_mclk.hw,
>>>> + [AUD2_CLKID_VAD_CLK_SEL] = &audio2_vad_clk_mux.hw,
>>>> + [AUD2_CLKID_VAD_CLK_DIV] = &audio2_vad_clk_div.hw,
>>>> + [AUD2_CLKID_VAD_CLK] = &audio2_vad_clk.hw,
>>>> + [AUD2_CLKID_PDM_DCLK_SEL] = &audio2_pdm_dclk_mux.hw,
>>>> + [AUD2_CLKID_PDM_DCLK_DIV] = &audio2_pdm_dclk_div.hw,
>>>> + [AUD2_CLKID_PDM_DCLK] = &audio2_pdm_dclk.hw,
>>>> + [AUD2_CLKID_PDM_SYSCLK_SEL] = &audio2_pdm_sysclk_mux.hw,
>>>> + [AUD2_CLKID_PDM_SYSCLK_DIV] = &audio2_pdm_sysclk_div.hw,
>>>> + [AUD2_CLKID_PDM_SYSCLK] = &audio2_pdm_sysclk.hw,
>>>> +};
>>>> +
>>>> +static struct meson_clk_hw_data a1_audio_clks = {
>>>> + .hws = a1_audio_hw_clks,
>>>> + .num = ARRAY_SIZE(a1_audio_hw_clks),
>>>> +};
>>>> +
>>>> +static struct regmap *a1_audio_map(struct platform_device *pdev,
>>>> + unsigned int index)
>>>> +{
>>>> + char name[32];
>>>> + const struct regmap_config cfg = {
>>>> + .reg_bits = 32,
>>>> + .val_bits = 32,
>>>> + .reg_stride = 4,
>>>> + .name = name,
>>>
>>> Not necessary
>>>
>>
>> This implementation uses two regmaps, and this field allow to avoid
>> errors like this:
>>
>> [ 0.145530] debugfs: Directory 'fe050000.audio-clock-controller' with
>> parent 'regmap' already present!
>>
>>>> + };
>>>> + void __iomem *base;
>>>> +
>>>> + base = devm_platform_ioremap_resource(pdev, index);
>>>> + if (IS_ERR(base))
>>>> + return base;
>>>> +
>>>> + scnprintf(name, sizeof(name), "%d", index);
>>>> + return devm_regmap_init_mmio(&pdev->dev, base, &cfg);
>>>> +}
>>>
>>> That is overengineered. Please keep it simple. Declare the regmap_config
>>> as static const global, and do it like axg-audio please.
>>>
>>
>> This only reason why it is not "static const" because I need to set
>> unique name for each regmap.
>>
>>>> +
>>>> +static int a1_register_clk(struct platform_device *pdev,
>>>> + struct regmap *map0, struct regmap *map1,
>>>> + struct clk_hw *hw)
>>>> +{
>>>> + struct clk_regmap *clk = container_of(hw, struct clk_regmap, hw);
>>>> +
>>>> + if (!hw)
>>>> + return 0;
>>>> +
>>>> + switch ((unsigned long)clk->map) {
>>>> + case AUDIO_RANGE_0:
>>>> + clk->map = map0;
>>>> + break;
>>>> + case AUDIO_RANGE_1:
>>>> + clk->map = map1;
>>>> + break;
>>>
>>> ... fishy
>>>
>>>> + default:
>>>> + WARN_ON(1);
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + return devm_clk_hw_register(&pdev->dev, hw);
>>>> +}
>>>> +
>>>> +static int a1_audio_clkc_probe(struct platform_device *pdev)
>>>> +{
>>>> + struct regmap *map0, *map1;
>>>> + struct clk *clk;
>>>> + unsigned int i;
>>>> + int ret;
>>>> +
>>>> + clk = devm_clk_get_enabled(&pdev->dev, "pclk");
>>>> + if (WARN_ON(IS_ERR(clk)))
>>>> + return PTR_ERR(clk);
>>>> +
>>>> + map0 = a1_audio_map(pdev, 0);
>>>> + if (IS_ERR(map0))
>>>> + return PTR_ERR(map0);
>>>> +
>>>> + map1 = a1_audio_map(pdev, 1);
>>>> + if (IS_ERR(map1))
>>>> + return PTR_ERR(map1);
>>>
>>> No - Looks to me you just have two clock controllers you are trying
>>> force into one.
>>>
>>
>> See the begining.
>>
>>>> +
>>>> + /*
>>>> + * Register and enable AUD2_CLKID_AUDIOTOP clock first. Unless
>>>> + * it is enabled any read/write to 'map0' hangs the CPU.
>>>> + */
>>>> +
>>>> + ret = a1_register_clk(pdev, map0, map1,
>>>> + a1_audio_clks.hws[AUD2_CLKID_AUDIOTOP]);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + ret = clk_prepare_enable(a1_audio_clks.hws[AUD2_CLKID_AUDIOTOP]->clk);
>>>> + if (ret)
>>>> + return ret;
>>>
>>> Again, this shows 2 devices. The one related to your 'map0' should
>>> request AUD2_CLKID_AUDIOTOP as input and enable it right away.
>>>
>>
>> See the begining.
>>
>>>> +
>>>> + for (i = 0; i < a1_audio_clks.num; i++) {
>>>> + if (i == AUD2_CLKID_AUDIOTOP)
>>>> + continue;
>>>> +
>>>> + ret = a1_register_clk(pdev, map0, map1, a1_audio_clks.hws[i]);
>>>> + if (ret)
>>>> + return ret;
>>>> + }
>>>> +
>>>> + ret = devm_of_clk_add_hw_provider(&pdev->dev, meson_clk_hw_get,
>>>> + &a1_audio_clks);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + BUILD_BUG_ON((unsigned long)AUDIO_REG_MAP(AUDIO_SW_RESET0) !=
>>>> + AUDIO_RANGE_0);
>>>
>>> Why is that necessary ?
>>>
>>
>> A little paranoia. Here AUDIO_SW_RESET0 is handled as map0's register,
>> and I want to assert it.
>>
>>>> + return meson_audio_rstc_register(&pdev->dev, map0,
>>>> + AUDIO_REG_OFFSET(AUDIO_SW_RESET0), 32);
>>>> +}
>>>> +
>>>> +static const struct of_device_id a1_audio_clkc_match_table[] = {
>>>> + { .compatible = "amlogic,a1-audio-clkc", },
>>>> + {}
>>>> +};
>>>> +MODULE_DEVICE_TABLE(of, a1_audio_clkc_match_table);
>>>> +
>>>> +static struct platform_driver a1_audio_clkc_driver = {
>>>> + .probe = a1_audio_clkc_probe,
>>>> + .driver = {
>>>> + .name = "a1-audio-clkc",
>>>> + .of_match_table = a1_audio_clkc_match_table,
>>>> + },
>>>> +};
>>>> +module_platform_driver(a1_audio_clkc_driver);
>>>> +
>>>> +MODULE_DESCRIPTION("Amlogic A1 Audio Clock driver");
>>>> +MODULE_AUTHOR("Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>");
>>>> +MODULE_LICENSE("GPL");
>>>> diff --git a/drivers/clk/meson/a1-audio.h b/drivers/clk/meson/a1-audio.h
>>>> new file mode 100644
>>>> index 000000000000..f994e87276cd
>>>> --- /dev/null
>>>> +++ b/drivers/clk/meson/a1-audio.h
>>>> @@ -0,0 +1,58 @@
>>>> +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
>>>> +/*
>>>> + * Copyright (c) 2024, SaluteDevices. All Rights Reserved.
>>>> + *
>>>> + * Author: Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>
>>>> + */
>>>> +
>>>> +#ifndef __A1_AUDIO_H
>>>> +#define __A1_AUDIO_H
>>>> +
>>>> +#define AUDIO_RANGE_0 0xa
>>>> +#define AUDIO_RANGE_1 0xb
>>>> +#define AUDIO_RANGE_SHIFT 16
>>>> +
>>>> +#define AUDIO_REG(_range, _offset) \
>>>> + (((_range) << AUDIO_RANGE_SHIFT) + (_offset))
>>>> +
>>>> +#define AUDIO_REG_OFFSET(_reg) \
>>>> + ((_reg) & ((1 << AUDIO_RANGE_SHIFT) - 1))
>>>> +
>>>> +#define AUDIO_REG_MAP(_reg) \
>>>> + ((void *)((_reg) >> AUDIO_RANGE_SHIFT))
>>>
>>> That is seriouly overengineered.
>>> The following are offset. Just write what they are.
>>>
>>
>> This is all in order to keep range's identifier together with offset and
>> then use it to store the identifier in clk_regmaps.
>>
>>> There is not reason to put that into a header. It is only going to be
>>> used by a single driver.
>>>>> +
>>>> +#define AUDIO_CLK_GATE_EN0 AUDIO_REG(AUDIO_RANGE_0, 0x000)
>>>> +#define AUDIO_MCLK_A_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x008)
>>>> +#define AUDIO_MCLK_B_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x00c)
>>>> +#define AUDIO_MCLK_C_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x010)
>>>> +#define AUDIO_MCLK_D_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x014)
>>>> +#define AUDIO_MCLK_E_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x018)
>>>> +#define AUDIO_MCLK_F_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x01c)
>>>> +#define AUDIO_SW_RESET0 AUDIO_REG(AUDIO_RANGE_0, 0x028)
>>>> +#define AUDIO_MST_A_SCLK_CTRL0 AUDIO_REG(AUDIO_RANGE_0, 0x040)
>>>> +#define AUDIO_MST_A_SCLK_CTRL1 AUDIO_REG(AUDIO_RANGE_0, 0x044)
>>>> +#define AUDIO_MST_B_SCLK_CTRL0 AUDIO_REG(AUDIO_RANGE_0, 0x048)
>>>> +#define AUDIO_MST_B_SCLK_CTRL1 AUDIO_REG(AUDIO_RANGE_0, 0x04c)
>>>> +#define AUDIO_MST_C_SCLK_CTRL0 AUDIO_REG(AUDIO_RANGE_0, 0x050)
>>>> +#define AUDIO_MST_C_SCLK_CTRL1 AUDIO_REG(AUDIO_RANGE_0, 0x054)
>>>> +#define AUDIO_MST_D_SCLK_CTRL0 AUDIO_REG(AUDIO_RANGE_0, 0x058)
>>>> +#define AUDIO_MST_D_SCLK_CTRL1 AUDIO_REG(AUDIO_RANGE_0, 0x05c)
>>>> +#define AUDIO_CLK_TDMIN_A_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x080)
>>>> +#define AUDIO_CLK_TDMIN_B_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x084)
>>>> +#define AUDIO_CLK_TDMIN_LB_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x08c)
>>>> +#define AUDIO_CLK_TDMOUT_A_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x090)
>>>> +#define AUDIO_CLK_TDMOUT_B_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x094)
>>>> +#define AUDIO_CLK_SPDIFIN_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x09c)
>>>> +#define AUDIO_CLK_RESAMPLE_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x0a4)
>>>> +#define AUDIO_CLK_LOCKER_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x0a8)
>>>> +#define AUDIO_CLK_EQDRC_CTRL AUDIO_REG(AUDIO_RANGE_0, 0x0c0)
>>>> +
>>>> +#define AUDIO2_CLK_GATE_EN0 AUDIO_REG(AUDIO_RANGE_1, 0x00c)
>>>> +#define AUDIO2_MCLK_VAD_CTRL AUDIO_REG(AUDIO_RANGE_1, 0x040)
>>>> +#define AUDIO2_CLK_VAD_CTRL AUDIO_REG(AUDIO_RANGE_1, 0x044)
>>>> +#define AUDIO2_CLK_PDMIN_CTRL0 AUDIO_REG(AUDIO_RANGE_1, 0x058)
>>>> +#define AUDIO2_CLK_PDMIN_CTRL1 AUDIO_REG(AUDIO_RANGE_1, 0x05c)
>>>> +
>>>> +#include <dt-bindings/clock/amlogic,a1-audio-clkc.h>
>>>> +
>>>> +#endif /* __A1_AUDIO_H */
>>>
>>>
>
>

--
Best regards
Jan Dakinevich