Re: [PATCH v4 4/4] arm64: dts: S32G3: Introduce device tree for S32G-VNP-RDB3

From: Wadim Mueller
Date: Mon Mar 25 2024 - 14:59:39 EST

On Mon, Mar 25, 2024 at 11:30:38AM +0200, Ghennadi Procopciuc wrote:
> On 3/24/24 23:43, Wadim Mueller wrote:
> > This commit adds device tree support for the NXP S32G3-based
> > S32G-VNP-RDB3 Board [1].
> >
> > The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.
> >
> > The device tree files are derived from the official NXP downstream
> > Linux tree [2].
> >
> > This addition encompasses a limited selection of peripherals that
> > are upstream-supported. Apart from the ARM System Modules
> > (GIC, Generic Timer, etc.), the following IPs have been validated:
> >
> > * UART: fsl-linflexuart
> > * SDHC: fsl-imx-esdhc
> >
> > Clock settings for the chip rely on ATF Firmware [3].
> > Pin control integration into the device tree is pending and currently
> > relies on Firmware/U-Boot settings [4].
> >
> > These changes were validated using BSP39 Firmware/U-Boot from NXP [5].
> >
> > The modifications enable booting the official Ubuntu 22.04 from NXP on
> > the RDB3 with default settings from the SD card and eMMC.
> >
> > [1] https://www.nxp.com/design/design-center/designs/s32g3-vehicle-networking-reference-design:S32G-VNP-RDB3
> > [2] https://github.com/nxp-auto-linux/linux
> > [3] https://github.com/nxp-auto-linux/arm-trusted-firmware
> > [4] https://github.com/nxp-auto-linux/u-boot
> > [5] https://github.com/nxp-auto-linux/auto_yocto_bsp
> >
> > Signed-off-by: Wadim Mueller <wafgo01@xxxxxxxxx>
> > ---
>
> Thank you, Wadim, for bringing up the S32G3RDB3 board! The board boots
> with all 8 cores. The log is attached below.
>

Thanks for testing Ghennadi, much appreciated.

According to MAINTAINERS all "dts/freescale/" DTS files
needs to go through the IMX/MXC tree?
Is my understanding correct? Just asking whether I understand the file
content correctly!

> Tested-by: Ghennadi Procopciuc <ghennadi.procopciuc@xxxxxxxxxxx>
> Reviewed-by: Ghennadi Procopciuc <ghennadi.procopciuc@xxxxxxxxxxx>
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
> [ 0.000000] Linux version 6.9.0-rc1-00004-gcb630dd69df3
> (nxa06643@lxl00026) (aarch64-linux-gnu-gcc (Linaro GCC 7.5-2019.12)
> 7.5.0, GNU ld (Linaro_Binutils-2019.12) 2.28.2.20170706) #21 SMP PREEMPT
> Mon Mar 25 10:50:16 EET 2024
> [ 0.000000] KASLR disabled due to lack of seed
> [ 0.000000] Machine model: NXP S32G3 Reference Design Board 3
> (S32G-VNP-RDB3)
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] OF: reserved mem: 0x00000000d0000000..0x00000000d000007f
> (0 KiB) nomap non-reusable shm@d0000000
> [ 0.000000] OF: reserved mem: 0x00000000ff600000..0x00000000ff7fffff
> (2048 KiB) nomap non-reusable atf@ff600000
> [ 0.000000] earlycon: linflex0 at MMIO 0x00000000401c8000 (options
> '115200n8')
> [ 0.000000] printk: legacy bootconsole [linflex0] enabled
> [ 0.000000] NUMA: No NUMA configuration found
> [ 0.000000] NUMA: Faking a node at [mem
> 0x0000000080000000-0x00000008dfffffff]
> [ 0.000000] NUMA: NODE_DATA [mem 0x8df8ff9c0-0x8df901fff]
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff]
> [ 0.000000] DMA32 empty
> [ 0.000000] Normal [mem 0x0000000100000000-0x00000008dfffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000cfffffff]
> [ 0.000000] node 0: [mem 0x00000000d0001000-0x00000000ff5fffff]
> [ 0.000000] node 0: [mem 0x00000000ff600000-0x00000000ff7fffff]
> [ 0.000000] node 0: [mem 0x00000000ff800000-0x00000000ffffffff]
> [ 0.000000] node 0: [mem 0x0000000880000000-0x00000008dfffffff]
> [ 0.000000] Initmem setup node 0 [mem
> 0x0000000080000000-0x00000008dfffffff]
> [ 0.000000] On node 0, zone DMA: 1 pages in unavailable ranges
> [ 0.000000] cma: Reserved 32 MiB at 0x00000000fd600000 on node -1
> [ 0.000000] psci: probing for conduit method from DT.
> [ 0.000000] psci: PSCIv1.1 detected in firmware.
> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
> [ 0.000000] psci: SMC Calling Convention v1.2
> [ 0.000000] percpu: Embedded 24 pages/cpu s57896 r8192 d32216 u98304
> [ 0.000000] Detected VIPT I-cache on CPU0
> [ 0.000000] CPU features: detected: GIC system register CPU interface
> [ 0.000000] CPU features: detected: ARM erratum 845719
> [ 0.000000] alternatives: applying boot alternatives
> [ 0.000000] Kernel command line: console=ttyLF0,115200
> root=/dev/mmcblk0p2 rootwait rw earlycon
> [ 0.000000] Dentry cache hash table entries: 524288 (order: 10,
> 4194304 bytes, linear)
> [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152
> bytes, linear)
> [ 0.000000] Fallback order for Node 0: 0
> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 903167
> [ 0.000000] Policy zone: Normal
> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [ 0.000000] software IO TLB: area num 8.
> [ 0.000000] software IO TLB: mapped [mem
> 0x00000000f9600000-0x00000000fd600000] (64MB)
> [ 0.000000] Memory: 3451804K/3670012K available (17472K kernel code,
> 4790K rwdata, 11432K rodata, 9984K init, 754K bss, 185440K reserved,
> 32768K cma-reserved)
> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
> [ 0.000000] rcu: RCU event tracing is enabled.
> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to
> nr_cpu_ids=8.
> [ 0.000000] Trampoline variant of Tasks RCU enabled.
> [ 0.000000] Tracing variant of Tasks RCU enabled.
> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay
> is 25 jiffies.
> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
> [ 0.000000] RCU Tasks: Setting shift to 3 and lim to 1
> rcu_task_cb_adjust=1.
> [ 0.000000] RCU Tasks Trace: Setting shift to 3 and lim to 1
> rcu_task_cb_adjust=1.
> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
> [ 0.000000] GICv3: 544 SPIs implemented
> [ 0.000000] GICv3: 0 Extended SPIs implemented
> [ 0.000000] Root IRQ handler: gic_handle_irq
> [ 0.000000] GICv3: GICv3 features: 16 PPIs
> [ 0.000000] GICv3: CPU0: found redistributor 0 region
> 0:0x0000000050900000
> [ 0.000000] ITS: No ITS available, not enabling LPIs
> [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on
> contention.
> [ 0.000000] arch_timer: cp15 timer(s) running at 5.00MHz (virt).
> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
> max_cycles: 0x127350b88, max_idle_ns: 440795202120 ns
> [ 0.000001] sched_clock: 56 bits at 5MHz, resolution 200ns, wraps
> every 4398046511100ns
> [ 0.008224] Console: colour dummy device 80x25
> [ 0.012493] Calibrating delay loop (skipped), value calculated using
> timer frequency.. 10.00 BogoMIPS (lpj=20000)
> [ 0.022661] pid_max: default: 32768 minimum: 301
> [ 0.027333] LSM: initializing lsm=capability
> [ 0.031604] Mount-cache hash table entries: 8192 (order: 4, 65536
> bytes, linear)
> [ 0.038904] Mountpoint-cache hash table entries: 8192 (order: 4,
> 65536 bytes, linear)
> [ 0.047831] cacheinfo: Unable to detect cache hierarchy for CPU 0
> [ 0.054481] rcu: Hierarchical SRCU implementation.
> [ 0.058926] rcu: Max phase no-delay instances is 1000.
> [ 0.064746] EFI services will not be available.
> [ 0.069258] smp: Bringing up secondary CPUs ...
> [ 0.073964] Detected VIPT I-cache on CPU1
> [ 0.074018] GICv3: CPU1: found redistributor 1 region
> 0:0x0000000050920000
> [ 0.074056] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
> [ 0.074630] Detected VIPT I-cache on CPU2
> [ 0.074662] GICv3: CPU2: found redistributor 2 region
> 0:0x0000000050940000
> [ 0.074682] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
> [ 0.075227] Detected VIPT I-cache on CPU3
> [ 0.075258] GICv3: CPU3: found redistributor 3 region
> 0:0x0000000050960000
> [ 0.075277] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
> [ 0.075831] Detected VIPT I-cache on CPU4
> [ 0.075885] GICv3: CPU4: found redistributor 100 region
> 0:0x0000000050980000
> [ 0.075917] CPU4: Booted secondary processor 0x0000000100 [0x410fd034]
> [ 0.076492] Detected VIPT I-cache on CPU5
> [ 0.076527] GICv3: CPU5: found redistributor 101 region
> 0:0x00000000509a0000
> [ 0.076547] CPU5: Booted secondary processor 0x0000000101 [0x410fd034]
> [ 0.077090] Detected VIPT I-cache on CPU6
> [ 0.077127] GICv3: CPU6: found redistributor 102 region
> 0:0x00000000509c0000
> [ 0.077147] CPU6: Booted secondary processor 0x0000000102 [0x410fd034]
> [ 0.077724] Detected VIPT I-cache on CPU7
> [ 0.077765] GICv3: CPU7: found redistributor 103 region
> 0:0x00000000509e0000
> [ 0.077785] CPU7: Booted secondary processor 0x0000000103 [0x410fd034]
> [ 0.077896] smp: Brought up 1 node, 8 CPUs
> [ 0.203873] SMP: Total of 8 processors activated.
> [ 0.208551] CPU: All CPU(s) started at EL1
> [ 0.212660] CPU features: detected: 32-bit EL0 Support
> [ 0.217751] CPU features: detected: 32-bit EL1 Support
> [ 0.222885] CPU features: detected: CRC32 instructions
> [ 0.228042] alternatives: applying system-wide alternatives
> [ 0.236019] devtmpfs: initialized
> [ 0.242628] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 7645041785100000 ns
> [ 0.252037] futex hash table entries: 2048 (order: 5, 131072 bytes,
> linear)
> [ 0.260021] pinctrl core: initialized pinctrl subsystem
> [ 0.266046] DMI not present or invalid.
> [ 0.272094] NET: Registered PF_NETLINK/PF_ROUTE protocol family
> [ 0.278654] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic
> allocations
> [ 0.285546] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for
> atomic allocations
> [ 0.293318] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for
> atomic allocations
> [ 0.301019] audit: initializing netlink subsys (disabled)
> [ 0.306513] audit: type=2000 audit(0.180:1): state=initialized
> audit_enabled=0 res=1
> [ 0.307304] thermal_sys: Registered thermal governor 'step_wise'
> [ 0.314096] thermal_sys: Registered thermal governor 'power_allocator'
> [ 0.320130] cpuidle: using governor menu
> [ 0.330730] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
> [ 0.337396] ASID allocator initialised with 65536 entries
> [ 0.344482] Serial: AMBA PL011 UART driver
> [ 0.350914] Modules: 21600 pages in range for non-PLT usage
> [ 0.350920] Modules: 513120 pages in range for PLT usage
> [ 0.356758] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
> [ 0.368493] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
> [ 0.374744] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
> [ 0.381511] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
> [ 0.387762] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
> [ 0.394531] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
> [ 0.400784] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
> [ 0.407551] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
> [ 0.414206] Demotion targets for Node 0: null
> [ 0.419168] ACPI: Interpreter disabled.
> [ 0.423692] iommu: Default domain type: Translated
> [ 0.428153] iommu: DMA domain TLB invalidation policy: strict mode
> [ 0.434805] SCSI subsystem initialized
> [ 0.438513] usbcore: registered new interface driver usbfs
> [ 0.443706] usbcore: registered new interface driver hub
> [ 0.448995] usbcore: registered new device driver usb
> [ 0.454351] pps_core: LinuxPPS API ver. 1 registered
> [ 0.458968] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
> Rodolfo Giometti <giometti@xxxxxxxx>
> [ 0.468095] PTP clock support registered
> [ 0.472054] EDAC MC: Ver: 3.0.0
> [ 0.475481] scmi_core: SCMI protocol bus registered
> [ 0.480546] FPGA manager framework
> [ 0.483666] Advanced Linux Sound Architecture Driver Initialized.
> [ 0.490590] vgaarb: loaded
> [ 0.493333] clocksource: Switched to clocksource arch_sys_counter
> [ 0.499297] VFS: Disk quotas dquot_6.6.0
> [ 0.503017] VFS: Dquot-cache hash table entries: 512 (order 0, 4096
> bytes)
> [ 0.510017] pnp: PnP ACPI: disabled
> [ 0.519430] NET: Registered PF_INET protocol family
> [ 0.524185] IP idents hash table entries: 65536 (order: 7, 524288
> bytes, linear)
> [ 0.533803] tcp_listen_portaddr_hash hash table entries: 2048 (order:
> 3, 32768 bytes, linear)
> [ 0.542061] Table-perturb hash table entries: 65536 (order: 6, 262144
> bytes, linear)
> [ 0.549719] TCP established hash table entries: 32768 (order: 6,
> 262144 bytes, linear)
> [ 0.557803] TCP bind hash table entries: 32768 (order: 8, 1048576
> bytes, linear)
> [ 0.566154] TCP: Hash tables configured (established 32768 bind 32768)
> [ 0.572472] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
> [ 0.579091] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes,
> linear)
> [ 0.586323] NET: Registered PF_UNIX/PF_LOCAL protocol family
> [ 0.592198] RPC: Registered named UNIX socket transport module.
> [ 0.597778] RPC: Registered udp transport module.
> [ 0.602457] RPC: Registered tcp transport module.
> [ 0.607143] RPC: Registered tcp-with-tls transport module.
> [ 0.612612] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 0.619048] PCI: CLS 0 bytes, default 64
> [ 0.623428] kvm [1]: HYP mode not available
> [ 0.628384] Initialise system trusted keyrings
> [ 0.632632] workingset: timestamp_bits=42 max_order=20 bucket_order=0
> [ 0.639182] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 0.644948] NFS: Registering the id_resolver key type
> [ 0.649780] Key type id_resolver registered
> [ 0.653921] Key type id_legacy registered
> [ 0.657932] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
> [ 0.664597] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver
> Registering...
> [ 0.672111] 9p: Installing v9fs 9p2000 file system support
> [ 0.714617] Key type asymmetric registered
> [ 0.718368] Asymmetric key parser 'x509' registered
> [ 0.723278] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 245)
> [ 0.730608] io scheduler mq-deadline registered
> [ 0.735119] io scheduler kyber registered
> [ 0.739144] io scheduler bfq registered
> [ 0.764751] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ 0.773400] 401c8000.serial: ttyLF0 at MMIO 0x401c8000 (irq = 14,
> base_baud = 0) is a FSL_LINFLEX
> [ 0.783976] printk: legacy console [ttyLF0] enabled
> [ 0.783976] printk: legacy console [ttyLF0] enabled
> [ 0.793930] printk: legacy bootconsole [linflex0] disabled
> [ 0.793930] printk: legacy bootconsole [linflex0] disabled
> [ 0.809777] 401cc000.serial: ttyLF1 at MMIO 0x401cc000 (irq = 15,
> base_baud = 0) is a FSL_LINFLEX
> [ 0.819329] msm_serial: driver initialized
> [ 0.823695] SuperH (H)SCI(F) driver initialized
> [ 0.828378] STM32 USART driver initialized
> [ 0.840105] loop: module loaded
> [ 0.844169] megasas: 07.727.03.00-rc1
> [ 0.852986] tun: Universal TUN/TAP device driver, 1.6
> [ 0.858691] thunder_xcv, ver 1.0
> [ 0.862013] thunder_bgx, ver 1.0
> [ 0.865323] nicpf, ver 1.0
> [ 0.868818] hns3: Hisilicon Ethernet Network Driver for Hip08 Family
> - version
> [ 0.876179] hns3: Copyright (c) 2017 Huawei Corporation.
> [ 0.881621] hclge is initializing
> [ 0.885029] e1000: Intel(R) PRO/1000 Network Driver
> [ 0.889999] e1000: Copyright (c) 1999-2006 Intel Corporation.
> [ 0.895874] e1000e: Intel(R) PRO/1000 Network Driver
> [ 0.900932] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
> [ 0.906982] igb: Intel(R) Gigabit Ethernet Network Driver
> [ 0.912483] igb: Copyright (c) 2007-2014 Intel Corporation.
> [ 0.918195] igbvf: Intel(R) Gigabit Virtual Function Network Driver
> [ 0.924581] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
> [ 0.930796] sky2: driver version 1.30
> [ 0.935382] VFIO - User Level meta-driver version: 0.3
> [ 0.942227] usbcore: registered new interface driver usb-storage
> [ 0.950179] i2c_dev: i2c /dev entries driver
> [ 0.959203] sdhci: Secure Digital Host Controller Interface driver
> [ 0.965503] sdhci: Copyright(c) Pierre Ossman
> [ 0.970334] Synopsys Designware Multimedia Card Interface Driver
> [ 0.976987] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 0.983975] ledtrig-cpu: registered to indicate activity on CPUs
> [ 0.990556] scmi_protocol scmi_dev.1: Enabled polling mode TX channel
> - prot_id:16
> [ 0.998513] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
> [ 1.005209] arm-scmi firmware:scmi: SCMI Protocol v2.0 'NXP:S32G399A'
> Firmware version 0x0
> [ 1.014897] cpu cpu0: EM: only supports uW power values
> [ 1.025027] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
> [ 1.032401] usbcore: registered new interface driver usbhid
> [ 1.038094] usbhid: USB HID core driver
> [ 1.044180] hw perfevents: enabled with armv8_cortex_a53 PMU driver,
> 7 counters available
> [ 1.056194] NET: Registered PF_PACKET protocol family
> [ 1.061445] 9pnet: Installing 9P2000 support
> [ 1.065867] Key type dns_resolver registered
> [ 1.079732] Timer migration: 1 hierarchy levels; 8 children per
> group; 1 crossnode level
> [ 1.088206] registered taskstats version 1
> [ 1.092820] Loading compiled-in X.509 certificates
> [ 1.115627] clk: Disabling unused clocks
> [ 1.117662] sdhci-esdhc-imx 402f0000.mmc: could not get pinctrl
> [ 1.119704] PM: genpd: Disabling unused power domains
> [ 1.130853] ALSA device list:
> [ 1.133886] No soundcards found.
> [ 1.157133] mmc0: SDHCI controller on 402f0000.mmc [402f0000.mmc]
> using ADMA
> [ 1.164512] Waiting for root device /dev/mmcblk0p2...
> [ 1.185787] mmc0: host does not support reading read-only switch,
> assuming write-enable
> [ 1.195000] mmc0: new high speed SDHC card at address 5048
> [ 1.201102] mmcblk0: mmc0:5048 SD32G 29.7 GiB
> [ 1.208397] mmcblk0: p1 p2
> [ 1.238459] EXT4-fs (mmcblk0p2): recovery complete
> [ 1.244613] EXT4-fs (mmcblk0p2): mounted filesystem
> 52830f5f-ab50-4125-a606-3c65100b7d4a r/w with ordered data mode. Quota
> mode: none.
> [ 1.257000] VFS: Mounted root (ext4 filesystem) on device 179:2.
> [ 1.264390] devtmpfs: mounted
> [ 1.271069] Freeing unused kernel memory: 9984K
> [ 1.275760] Run /sbin/init as init process
> [ 1.657291] systemd[1]: System time before build time, advancing clock.
> [ 1.714423] systemd[1]: systemd 250.5+ running in system mode (+PAM
> -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL
> +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP
> +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2 -LZ4 -XZ -ZLIB
> +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid)
> [ 1.746891] systemd[1]: Detected architecture arm64.
>
> Welcome to Auto Linux BSP develop (kirkstone)!
>
> [ 1.845928] systemd[1]: Hostname set to <s32g399ardb3>.
> [ 2.186158] systemd[1]: Binding to IPv6 address not available since
> kernel does not support IPv6.
> [ 2.195287] systemd[1]: Binding to IPv6 address not available since
> kernel does not support IPv6.
> [ 2.317364] systemd[1]: Queued start job for default target
> Multi-User System.
> [ 2.396694] systemd[1]: Created slice Slice /system/getty.
> [ OK ] Created slice Slice /system/getty.
> [ 2.410476] systemd[1]: Created slice Slice /system/modprobe.
> [ OK ] Created slice Slice /system/modprobe.
> [ 2.424209] systemd[1]: Created slice Slice /system/serial-getty.
> [ OK ] Created slice Slice /system/serial-getty.
> [ 2.438389] systemd[1]: Created slice User and Session Slice.
> [ OK ] Created slice User and Session Slice.
> [ 2.450954] systemd[1]: Started Dispatch Password Requests to Console
> Directory Watch.
> [ OK ] Started Dispatch Password …ts to Console Directory Watch.
> [ 2.467638] systemd[1]: Started Forward Password Requests to Wall
> Directory Watch.
> [ OK ] Started Forward Password R…uests to Wall Directory Watch.
> [ 2.484011] systemd[1]: Reached target Path Units.
> [ OK ] Reached target Path Units.
> [ 2.494464] systemd[1]: Reached target Remote File Systems.
> [ OK ] Reached target Remote File Systems.
> [ 2.506485] systemd[1]: Reached target Slice Units.
> [ OK ] Reached target Slice Units.
> [ 2.517119] systemd[1]: Reached target Swaps.
> [ OK ] Reached target Swaps.
> [ 2.586411] systemd[1]: Listening on RPCbind Server Activation Socket.
> [ OK ] Listening on RPCbind Server Activation Socket.
> [ 2.600701] systemd[1]: Reached target RPC Port Mapper.
> [ OK ] Reached target RPC Port Mapper.
> [ 2.612616] systemd[1]: Listening on Syslog Socket.
> [ OK ] Listening on Syslog Socket.
> [ 2.623452] systemd[1]: Listening on initctl Compatibility Named Pipe.
> [ OK ] Listening on initctl Compatibility Named Pipe.
> [ 2.637954] systemd[1]: Listening on Journal Audit Socket.
> [ OK ] Listening on Journal Audit Socket.
> [ 2.650037] systemd[1]: Listening on Journal Socket (/dev/log).
> [ OK ] Listening on Journal Socket (/dev/log).
> [ 2.663102] systemd[1]: Listening on Journal Socket.
> [ OK ] Listening on Journal Socket.
> [ 2.674363] systemd[1]: Listening on Network Service Netlink Socket.
> [ OK ] Listening on Network Service Netlink Socket.
> [ 2.688327] systemd[1]: Listening on udev Control Socket.
> [ OK ] Listening on udev Control Socket.
> [ 2.700193] systemd[1]: Listening on udev Kernel Socket.
> [ OK ] Listening on udev Kernel Socket.
> [ 2.711963] systemd[1]: Listening on User Database Manager Socket.
> [ OK ] Listening on User Database Manager Socket.
> [ 2.749696] systemd[1]: Mounting Huge Pages File System...
> Mounting Huge Pages File System...
> [ 2.764346] systemd[1]: Mounting POSIX Message Queue File System...
> Mounting POSIX Message Queue File System...
> [ 2.780591] systemd[1]: Mounting Kernel Debug File System...
> Mounting Kernel Debug File System...
> [ 2.792560] systemd[1]: Kernel Trace File System was skipped because
> of a failed condition check (ConditionPathExists=/sys/kernel/tracing).
> [ 2.805768] systemd[1]: Create List of Static Device Nodes was
> skipped because of a failed condition check
> (ConditionFileNotEmpty=/lib/modules/6.9.0-rc1-00004-gcb630dd69df3/modules.devname).
> [ 2.826957] systemd[1]: Starting Load Kernel Module configfs...
> Starting Load Kernel Module configfs...
> [ 2.842860] systemd[1]: Starting Load Kernel Module drm...
> Starting Load Kernel Module drm...
> [ 2.857874] systemd[1]: Starting Load Kernel Module fuse...
> Starting Load Kernel Module fuse...
> [ 2.879679] systemd[1]: Starting RPC Bind...
> Starting RPC Bind...
> [ 2.888514] systemd[1]: File System Check on Root Device was skipped
> because of a failed condition check (ConditionPathIsReadWrite=!/).
> [ 2.907067] systemd[1]: Starting Journal Service...
> Starting Journal Service...
> [ 2.925119] systemd[1]: Starting Load Kernel Modules...
> Starting Load Kernel Modules...
> [ 2.940298] systemd[1]: Starting Generate network units from Kernel
> command line...
> Starting Generate network …ts from Kernel command line...
> [ 2.959955] systemd[1]: Starting Remount Root and Kernel File Systems...
> Starting Remount Root and Kernel File Systems...
> [ 2.977958] systemd[1]: Starting Coldplug All udev Devices...
> Starting Coldplug All udev Devices...
> [ 2.995944] systemd[1]: Started RPC Bind.
> [ OK ] Started RPC Bind.
> [ 3.005902] systemd[1]: Mounted Huge Pages File System.
> [ OK ] Mounted Huge Pages File System.
> [ 3.018033] systemd[1]: Mounted POSIX Message Queue File System.
> [ OK ] Mounted POSIX Message Queue File System.[ 3.029658] EXT4-fs
> (mmcblk0p2): re-mounted 52830f5f-ab50-4125-a606-3c65100b7d4a r/w. Quota
> mode: none.
>
> [ 3.043175] systemd[1]: Started Journal Service.
> [ OK ] Started Journal Service.
> [ OK ] Mounted Kernel Debug File System.
> [ OK ] Finished Load Kernel Module configfs.
> [ OK ] Finished Load Kernel Module drm.
> [ OK ] Finished Load Kernel Module fuse.
> [FAILED] Failed to start Load Kernel Modules.
> See 'systemctl status systemd-modules-load.service' for details.
> [ OK ] Finished Generate network units from Kernel command line.
> [ OK ] Finished Remount Root and Kernel File Systems.
> Mounting Kernel Configuration File System...
> Starting Flush Journal to Persistent Storage...
> Starting Apply Kernel Variables...
> Starting Create Static Device Nodes in /dev...[ 3.206617]
> systemd-journald[124]: Received client request to flush runtime journal.
>
> [ OK ] Mounted Kernel Configuration File System.
> [ OK ] Finished Flush Journal to Persistent Storage.
> [ OK ] Finished Apply Kernel Variables.
> [ OK ] Finished Create Static Device Nodes in /dev.
> [ OK ] Reached target Preparation for Local File Systems.
> Mounting /tmp...
> Mounting /var/volatile...
> [ 3.338366] audit: type=1334 audit(1651167746.684:2): prog-id=5 op=LOAD
> [ 3.345166] audit: type=1334 audit(1651167746.688:3): prog-id=6 op=LOAD
> Starting Rule-based Manage…for Device Events and Files...
> [ OK ] Mounted /tmp.
> [ OK ] Mounted /var/volatile.
> Mounting /var/volatile/tmp...
> Starting Load/Save Random Seed...
> [ OK ] Mounted /var/volatile/tmp.
> [ OK ] Reached target Local File Systems.
> Starting Create Volatile Files and Directories...
> [ OK ] Finished Create Volatile Files and Directories.
> Starting Network Time Synchronization...
> Starting Record System Boot/Shutdown in UTMP...
> [ OK ] Started Rule-based Manager for Device Events and Files.
> [ OK ] Finished Coldplug All udev Devices.
> [ OK ] Finished Record System Boot/Shutdown in UTMP.
> [ OK ] Started Network Time Synchronization.
> [ OK ] Reached target System Initialization.
> [ OK ] Started Daily Cleanup of Temporary Directories.
> [ OK ] Reached target System Time Set.
> [ OK ] Started Daily rotation of log files.
> [ OK ] Reached target Timer Units.
> [ OK ] Listening on D-Bus System Message Bus Socket.
> Starting sshd.socket...
> [ OK ] Listening on sshd.socket.
> [ OK ] Reached target Socket Units.
> [ OK ] Reached target Basic System.
> [ OK ] Started Job spooling tools.
> [ OK ] Started Periodic Command Scheduler.
> Starting D-Bus System Message Bus...
> Starting IPv6 Packet Filtering Framework...
> Starting IPv4 Packet Filtering Framework...
> [ OK ] Started irqbalance daemon.
> [ OK ] Started Hardware RNG Entropy Gatherer Daemon.
> [ OK ] Started System Logging Service.
> Starting Resets System Activity Logs...
> [ 4.124453] audit: type=1334 audit(1651254541.860:4): prog-id=7 op=LOAD
> [ 4.131266] audit: type=1334 audit(1651254541.868:5): prog-id=8 op=LOAD
> Starting User Login Management...
> Starting OpenSSH Key Generation...
> [ OK ] Finished IPv6 Packet Filtering Framework.
> [ OK ] Finished IPv4 Packet Filtering Framework.
> [ OK ] Reached target Preparation for Network.
> Starting Network Configuration...
> [ OK ] Finished Resets System Activity Logs.
> [ OK ] Finished OpenSSH Key Generation.
> [ OK ] Started Network Configuration.
> Starting Network Name Resolution...
> [ OK ] Started Network Name Resolution.
> [ OK ] Reached target Network.
> [ OK ] Reached target Host and Network Name Lookups.
> [ OK ] Started Netperf Benchmark Server.
> [ OK ] Started NFS status monitor for NFSv2/3 locking..
> [ OK ] Started Respond to IPv6 Node Information Queries.
> [ OK ] Started Network Router Discovery Daemon.
> Starting Permit User Sessions...
> [ OK ] Started Xinetd A Powerful Replacement For Inetd.
> [ OK ] Finished Permit User Sessions.
> [ OK ] Started Getty on tty1.
> [ OK ] Started Serial Getty on ttyLF0.
> [ OK ] Reached target Login Prompts.
> [ OK ] Created slice Slice /system/systemd-fsck.
> [ OK ] Found device /dev/mmcblk0p1.
> Starting File System Check on /dev/mmcblk0p1...
> [ OK ] Finished File System Check on /dev/mmcblk0p1.
> Mounting /run/media/boot_s32g3-mmcblk0p1...
> [ OK ] Mounted /run/media/boot_s32g3-mmcblk0p1.
> [ OK ] Finished Load/Save Random Seed.
> [ OK ] Started D-Bus System Message Bus.
> [ OK ] Started User Login Management.
> [ OK ] Reached target Multi-User System.
> Starting Record Runlevel Change in UTMP...
> [ OK ] Finished Record Runlevel Change in UTMP.
>
>
> Regards,
> Ghennadi
>