Re: [PATCH] usb: Disable USB3 LPM at shutdown

[Kai-Heng Feng]

On Tue, Mar 26, 2024 at 1:56 PM Greg KH <gregkh@xxxxxxxxxxxxxxxxxxx> wrote:
>
> On Tue, Mar 05, 2024 at 02:51:38PM +0800, Kai-Heng Feng wrote:
> > SanDisks USB3 storage may disapper after system reboot:
> >
> > usb usb2-port3: link state change
> > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
> > usb usb2-port3: do warm reset, port only
> > xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
> > usb usb2-port3: not warm reset yet, waiting 50ms
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
> > usb usb2-port3: not warm reset yet, waiting 200ms
> > ...
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
> > usb usb2-port3: not warm reset yet, waiting 200ms
> > xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
> > xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
> > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
> > usb usb2-port3: not enabled, trying warm reset again...
> >
> > This is due to the USB device still cause port change event after xHCI is
> > shuted down:
> >
> > xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
> > xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
> > xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
> > xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
> > xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
> > xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
> > xhci_hcd 0000:38:00.0: // Halt the HC
> > xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
> > xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
> > xhci_hcd 0000:00:14.0: // Halt the HC
> > xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
> > xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status  = 0x1311
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
> > xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
> > xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
> > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
> > xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
> > usb 2-3: device not accepting address 2, error -108
> > xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
> > xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
> > xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status  = 0x1271
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
> > usb usb2-port3: not reset yet, waiting 60ms
> > ACPI: PM: Preparing to enter system sleep state S5
> > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
> > usb usb2-port3: not reset yet, waiting 200ms
> > reboot: Restarting system
> >
> > The port change event is caused by LPM transition, so disabling LPM at shutdown
> > to make sure the device is in U0 for warmboot.
> >
> > Signed-off-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
> > ---
> >  drivers/usb/core/port.c | 4 +++-
> >  1 file changed, 3 insertions(+), 1 deletion(-)
>
> What commit id does this fix?

This isn't a regression, so if this question is for stable kernel, I
think all supported kernel should get the fix.

Kai-Heng