[PATCH] phy: qcom: qmp-combo: Fix VCO div offset on v3

[Stephen Boyd]

Commit ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to
setup clocks") changed the offset that is used to write to
DP_PHY_VCO_DIV from QSERDES_V3_DP_PHY_VCO_DIV to
QSERDES_V4_DP_PHY_VCO_DIV. Unfortunately, this offset is different
between v3 and v4 phys:

 #define QSERDES_V3_DP_PHY_VCO_DIV                 0x064
 #define QSERDES_V4_DP_PHY_VCO_DIV                 0x070

meaning that we write the wrong register on v3 phys now. Add another
generic register to 'regs' and use it here instead of a version specific
define to fix this.

This was discovered after Abhinav looked over register dumps with me
from sc7180 Trogdor devices that started failing to light up the
external display with v6.6 based kernels. It turns out that some
monitors are very specific about their link clk frequency and if the
default power on reset value is still there the monitor will show a
blank screen or a garbled display. Other monitors are perfectly happy to
get a bad clock signal.

Cc: Douglas Anderson <dianders@xxxxxxxxxxxx>
Cc: Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx>
Cc: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
Fixes: ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to setup clocks")
Signed-off-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 7d585a4bbbba..3b19d8ebf467 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -77,6 +77,7 @@ enum qphy_reg_layout {
 	QPHY_COM_BIAS_EN_CLKBUFLR_EN,
 
 	QPHY_DP_PHY_STATUS,
+	QPHY_DP_PHY_VCO_DIV,
 
 	QPHY_TX_TX_POL_INV,
 	QPHY_TX_TX_DRV_LVL,
@@ -102,6 +103,7 @@ static const unsigned int qmp_v3_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_COM_BIAS_EN_CLKBUFLR_EN]	= QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN,
 
 	[QPHY_DP_PHY_STATUS]		= QSERDES_V3_DP_PHY_STATUS,
+	[QPHY_DP_PHY_VCO_DIV]		= QSERDES_V3_DP_PHY_VCO_DIV,
 
 	[QPHY_TX_TX_POL_INV]		= QSERDES_V3_TX_TX_POL_INV,
 	[QPHY_TX_TX_DRV_LVL]		= QSERDES_V3_TX_TX_DRV_LVL,
@@ -126,6 +128,7 @@ static const unsigned int qmp_v45_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_COM_BIAS_EN_CLKBUFLR_EN]	= QSERDES_V4_COM_BIAS_EN_CLKBUFLR_EN,
 
 	[QPHY_DP_PHY_STATUS]		= QSERDES_V4_DP_PHY_STATUS,
+	[QPHY_DP_PHY_VCO_DIV]		= QSERDES_V4_DP_PHY_VCO_DIV,
 
 	[QPHY_TX_TX_POL_INV]		= QSERDES_V4_TX_TX_POL_INV,
 	[QPHY_TX_TX_DRV_LVL]		= QSERDES_V4_TX_TX_DRV_LVL,
@@ -2162,6 +2165,7 @@ static int qmp_combo_configure_dp_clocks(struct qmp_combo *qmp)
 	const struct phy_configure_opts_dp *dp_opts = &qmp->dp_opts;
 	u32 phy_vco_div;
 	unsigned long pixel_freq;
+	const struct qmp_phy_cfg *cfg = qmp->cfg;
 
 	switch (dp_opts->link_rate) {
 	case 1620:
@@ -2184,7 +2188,7 @@ static int qmp_combo_configure_dp_clocks(struct qmp_combo *qmp)
 		/* Other link rates aren't supported */
 		return -EINVAL;
 	}
-	writel(phy_vco_div, qmp->dp_dp_phy + QSERDES_V4_DP_PHY_VCO_DIV);
+	writel(phy_vco_div, qmp->dp_dp_phy + cfg->regs[QPHY_DP_PHY_VCO_DIV]);
 
 	clk_set_rate(qmp->dp_link_hw.clk, dp_opts->link_rate * 100000);
 	clk_set_rate(qmp->dp_pixel_hw.clk, pixel_freq);

base-commit: 4cece764965020c22cff7665b18a012006359095
-- 
https://chromeos.dev