Re: [PATCH 05/26] cxl/core: Simplify cxl_dpa_set_mode()

From: Alison Schofield
Date: Mon Apr 08 2024 - 20:43:38 EST


On Sun, Mar 24, 2024 at 04:18:08PM -0700, Ira Weiny wrote:
> cxl_dpa_set_mode() checks the mode for validity two times, once outside
> of the DPA RW semaphore and again within.

Not true. It only checks mode once before the lock. It checks for
capacity after the lock. If it didn't check mode before the lock,
then unsupported modes would fall through.

> The function is not in a critical path.

Implying what here? OK to check twice (even though it wasn't)
or OK to expand scope of locking.

> Prior to Dynamic Capacity the extra check was not much
> of an issue. The addition of DC modes increases the complexity of
> the check.
>
> Simplify the mode check before adding the more complex DC modes.
>

The addition of the DC mode check doesn't seem complex.

Pardon my picking at the words, but if you'd like to refactor the
function, just say so. The final result is a bit more readable, but
also adding the DC mode checks without refactoring would read fine
also.

and...a bit spacing nit below -

> Signed-off-by: Ira Weiny <ira.weiny@xxxxxxxxx>
>
> ---
> Changes for v1:
> [iweiny: new patch]
> [Jonathan: based on getting rid of the loop in cxl_dpa_set_mode]
> [Jonathan: standardize on resource_size() == 0]
> ---
> drivers/cxl/core/hdm.c | 45 ++++++++++++++++++---------------------------
> 1 file changed, 18 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c
> index 7d97790b893d..66b8419fd0c3 100644
> --- a/drivers/cxl/core/hdm.c
> +++ b/drivers/cxl/core/hdm.c
> @@ -411,44 +411,35 @@ int cxl_dpa_set_mode(struct cxl_endpoint_decoder *cxled,
> struct cxl_memdev *cxlmd = cxled_to_memdev(cxled);
> struct cxl_dev_state *cxlds = cxlmd->cxlds;
> struct device *dev = &cxled->cxld.dev;
> - int rc;
>
> + guard(rwsem_write)(&cxl_dpa_rwsem);
> + if (cxled->cxld.flags & CXL_DECODER_F_ENABLE)
> + return -EBUSY;
> +
> + /*
> + * Check that the mode is supported by the current partition
> + * configuration
> + */
> switch (mode) {
> case CXL_DECODER_RAM:
> + if (!resource_size(&cxlds->ram_res)) {
> + dev_dbg(dev, "no available ram capacity\n");
> + return -ENXIO;
> + }
> + break;
> case CXL_DECODER_PMEM:
> + if (!resource_size(&cxlds->pmem_res)) {
> + dev_dbg(dev, "no available pmem capacity\n");
> + return -ENXIO;
> + }
> break;
> default:
> dev_dbg(dev, "unsupported mode: %d\n", mode);
> return -EINVAL;
> }
>

delete extra line

> - down_write(&cxl_dpa_rwsem);
> - if (cxled->cxld.flags & CXL_DECODER_F_ENABLE) {
> - rc = -EBUSY;
> - goto out;
> - }
> -
> - /*
> - * Only allow modes that are supported by the current partition
> - * configuration
> - */
> - if (mode == CXL_DECODER_PMEM && !resource_size(&cxlds->pmem_res)) {
> - dev_dbg(dev, "no available pmem capacity\n");
> - rc = -ENXIO;
> - goto out;
> - }
> - if (mode == CXL_DECODER_RAM && !resource_size(&cxlds->ram_res)) {
> - dev_dbg(dev, "no available ram capacity\n");
> - rc = -ENXIO;
> - goto out;
> - }
> -
> cxled->mode = mode;
> - rc = 0;
> -out:
> - up_write(&cxl_dpa_rwsem);
> -
> - return rc;
insert blank line
> + return 0;
> }
>
> int cxl_dpa_alloc(struct cxl_endpoint_decoder *cxled, unsigned long long size)
>
> --
> 2.44.0
>