[PATCH 4/5] arm64: dts: mediatek: mt8395-nio-12l: Enable PHYs and USB role switch

[AngeloGioacchino Del Regno]

Enable the PCIe0 PHY to be able to set calibrations read from eFuses,
improving the stability and performance of the PCIe link.

While at it, also enable the T-PHYs for both PCIe1 and for USB, allowing
the USB ports to finally switch to gadget mode if needed, and configure
the VBUS/ID pins of both USB ports for the same.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
---
 .../dts/mediatek/mt8395-radxa-nio-12l.dts     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
index f699633659b6..5cbe969da425 100644
--- a/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
@@ -685,6 +685,26 @@ pins-bus {
 		};
 	};
 
+	usb3_port0_pins: usb3p0-default-pins {
+		pins-vbus {
+			pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>;
+			input-enable;
+		};
+	};
+
+	usb2_port0_pins: usb2p0-default-pins {
+		pins-iddig {
+			pinmux = <PINMUX_GPIO130__FUNC_IDDIG_1P>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-vbus {
+			pinmux = <PINMUX_GPIO131__FUNC_USB_DRVVBUS_1P>;
+			output-low;
+		};
+	};
+
 	wifi_vreg_pins: wifi-vreg-pins {
 		pins-wifi-pmu-en {
 			pinmux = <PINMUX_GPIO65__FUNC_GPIO65>;
@@ -709,6 +729,10 @@ &pcie1 {
 	status = "okay";
 };
 
+&pciephy {
+	status = "okay";
+};
+
 &pmic {
 	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
 };
@@ -776,6 +800,18 @@ mt6315_7_vbuck1: vbuck1 {
 	};
 };
 
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
 &uart0 {
 	/* Exposed at 40 pin connector */
 	pinctrl-0 = <&uart0_pins>;
@@ -791,6 +827,8 @@ &uart1 {
 };
 
 &ssusb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb3_port0_pins>;
 	role-switch-default-mode = "host";
 	usb-role-switch;
 	vusb33-supply = <&mt6359_vusb_ldo_reg>;
@@ -804,6 +842,8 @@ mtu3_hs0_role_sw: endpoint {
 };
 
 &ssusb2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb2_port0_pins>;
 	vusb33-supply = <&mt6359_vusb_ldo_reg>;
 	status = "okay";
 };
-- 
2.44.0