Re: [PATCH net-next v3 06/12] net: ethernet: oa_tc6: implement internal PHY initialization
From: Parthiban.Veerasooran
Date: Fri Apr 12 2024 - 06:43:40 EST
Hi Andrew,
On 18/03/24 4:31 pm, Parthiban.Veerasooran@xxxxxxxxxxxxx wrote:
> Hi Andrew,
>
> On 08/03/24 7:03 pm, Andrew Lunn wrote:
>> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>>
>>> Ok, as per the table 6 in the spec, PHY C45 registers are mapped in the
>>> MMS like below,
>>>
>>> PHY – PCS Registers (MMD 3) ---> MMS 2
>>> PHY – PMA/PMD Registers (MMD 1) ---> MMS 3
>>> PHY – Vendor Specific and PLCA Registers (MMD 31) ---> MMS 4
>>> PHY – Auto-Negotiation Registers (MMD 7) ---> MMS 5
>>> PHY – Power Unit (MMD 13) ---> MMS 6
>>>
>>> MMD 13 for PHY - Power Unit is not defined in the mdio.h. So in the
>>> below code I have defined it locally (MDIO_MMD_POWER_UNIT). May be
>>> needed to do this in the mdio.h file when coming to this patch.
>>
>> Yes, please add it to mdio.h
> Sure will add it in the mdio.h file.
>>
>>> /* PHY – Clause 45 registers memory map selector (MMS) as per table 6 in
>>> the OPEN Alliance specification.
>>> */
>>> #define OA_TC6_PHY_PCS_MMS2 2 /* MMD 3 */
>>> #define OA_TC6_PHY_PMA_PMD_MMS3 3 /* MMD 1 */
>>> #define OA_TC6_PHY_VS_PLCA_MMS4 4 /* MMD 31 */
>>> #define OA_TC6_PHY_AUTO_NEG_MMS5 5 /* MMD 7 */
>>> #define OA_TC6_PHY_POWER_UNIT_MMS6 6 /* MMD 13 */
>>>
>>> /* MDIO Manageable Device (MMD) for PHY Power Unit */
>>> #define MDIO_MMD_POWER_UNIT 13 /* PHY Power Unit */
>>>
>>> static int oa_tc6_mdiobus_read_c45(struct mii_bus *bus, int addr, int
>>> devnum, int regnum)
>>> {
>>>
>>> struct oa_tc6 *tc6 = bus->priv;
>>>
>>> u32 regval;
>>>
>>> bool ret;
>>>
>>> u32 mms;
>>>
>>>
>>>
>>> if (devnum == MDIO_MMD_PCS)
>>>
>>> mms = OA_TC6_PHY_PCS_MMS2;
>>>
>>> else if (devnum == MDIO_MMD_PMAPMD)
>>>
>>> mms = OA_TC6_PHY_PMA_PMD_MMS3;
>>>
>>> else if (devnum == MDIO_MMD_VEND2)
>>>
>>> mms = OA_TC6_PHY_VS_PLCA_MMS4;
>>>
>>> else if (devnum == MDIO_MMD_AN)
>>>
>>> mms = OA_TC6_PHY_AUTO_NEG_MMS5;
>>>
>>> else if (devnum == MDIO_MMD_POWER_UNIT)
>>>
>>> mms = OA_TC6_PHY_POWER_UNIT_MMS6;
>>
>> I would probably use a switch statement.
> Ah ok, I will use switch here.
>>
>>>
>>> else
>>>
>>> return -ENOTSUPP;
>>
>> 802.3 says:
>>
>> If a device supports the MDIO interface it shall respond to all
>> possible register addresses for the device and return a value of
>> zero for undefined and unsupported registers. Writes to undefined
>> registers and read-only registers shall have no effect. The
>> operation of an MMD shall not be affected by writes to reserved and
>> unsupported register bits, and such register bits shall return a
>> value of zero when read.
>>
>> So maybe return 0. ENOTSUPP is wrong, that is an NFS only error
>> code. The generic one is EOPNOTSUPP. I would say -EOPNOTSUPP is also
>> O.K.
> Sure, I will use -EOPNOTSUPP in the next version instead of -ENOTSUPP.
>>
>>> ret = oa_tc6_read_register(tc6, (mms << 16) | regnum, ®val);
>>>
>>> if (ret)
>>>
>>> return -ENODEV;
>>
>> oa_tc6_read_register() should return an error code, so return whatever
>> is returns. Don't overwrite error codes. It makes it harder to track
>> errors through the call stack.
> Ah ok, will return the error code from oa_tc6_read_register() in the
> next version.
After implementing the new APIs oa_tc6_mdiobus_read_c45() and
oa_tc6_mdiobus_write_c45(), I tried testing. But, for some reason these
APIs are never get called by phy_read_mmd() or phy_write_mmd() as those
APIs are checking for phydev->is_c45 flag for calling this new c45 APIs
which is not set in this case.
If the phydev is found via c22, phylib does not set phydev->is_c45, and
everything ends up going indirect.
To verify the APIs, I just called them locally withing the oa_tc6_init()
function, there I got the expected results but accessing them through
phylib is not working because of the above reason.
Do you have any idea or suggestion to test this APIs or do I miss
anything here?
Best regards,
Parthiban V
>
> Best regards,
> Parthiban V
>>
>> Andrew
>>
>