Re: [PATCH] cpufreq/cppc: changing highest_perf to nominal_perf in cppc_cpufreq_cpu_init()

From: liwei (JK)
Date: Thu May 09 2024 - 23:07:04 EST


Hello,

Thanks for for your reply.

Maybe my description has caused you some misunderstandings, please allow me to supplement the description

在 2024/5/7 18:25, Ionela Voinescu 写道:
Hi,

Thanks for adding me to this.

On Monday 29 Apr 2024 at 16:19:45 (+0530), Viresh Kumar wrote:
CC'ing few folks who are working with the driver.

On 28-04-24, 17:28, liwei wrote:
When turning on turbo, if frequency configuration takes effect slowly,
the updated policy->cur may be equal to the frequency configured in
governor->limits(), performance governor will not adjust the frequency,
configured frequency will remain at turbo-freq.

Simplified call stack looks as follows:
cpufreq_register_driver(&cppc_cpufreq_driver)
...
cppc_cpufreq_cpu_init()
cppc_get_perf_caps()
policy->max = cppc_perf_to_khz(caps, caps->nominal_perf)
cppc_set_perf(highest_perf) // set highest_perf
policy->cur = cpufreq_driver->get() // if cur == policy->max
cpufreq_init_policy()
...
cpufreq_start_governor() // governor: performance
new_freq = cpufreq_driver->get() // if new_freq == policy->max
if (policy->cur != new_freq)
cpufreq_out_of_sync(policy, new_freq)
...
policy->cur = new_freq
I believe the problem is here ^^^^^^^^^^^^^^^^^^^^^^.

cpufreq_verify_current_freq() should not update policy->cur unless a
request to change frequency has actually reached the driver. I believe
policy->cur should always reflect the request, not the actual current
frequency of the CPU.

Given that new_freq is the current (hardware) frequency of the CPU,
obtained via .get(), it can be the nominal frequency, as it is in your
case, or any frequency, if there is any firmware/hardware capping in
place.

This causes the issue in your scenario, in which __cpufreq_driver_target()
filters the request from the governor as it finds it equal to policy->cur,
and it believes it's already set by hardware.

This causes another issue in which scaling_cur_freq, which for some
systems returns policy->cur, ends up returning the hardware frequency of
the CPUs, and not the last frequency request, as it should:

"scaling_cur_freq
Current frequency of all of the CPUs belonging to this policy (in kHz).

In the majority of cases, this is the frequency of the last P-state
requested by the scaling driver from the hardware using the scaling
interface provided by it, which may or may not reflect the frequency
the CPU is actually running at (due to hardware design and other
limitations)." [1]

Therefore policy->cur gets polluted with the hardware frequency of the
CPU sampled at that one time, and this affects governor decisions, as
in your case, and scaling_cur_freq feedback as well. This bad value will
not change until there's another .target() or cpufreq_out_of_sync()
call, which will never happen for fixed frequency governors like the
performance governor.

Thanks,
Ionela.


In the above function calling process, the frequency is obtained twice. The first time is in cpufreq_online(), and the second time is in cpufreq_verify_current_freq().

When the frequency configuration takes effect slowly, the kernel cannot sense when the frequency configuration takes effect. It may take effect before the frequency is read twice, between the frequencies read twice, or after the frequency is read twice.

|------------------|--------------------|---------------------|
set highest_freq get() get() target()

If it takes effect before two read operations, there will be no problem.

If it takes effect between two read operations, policy->cur will be updated in cpufreq_verify_current_freq(), the execution path is as follows:
new_freq = cpufreq_driver->get() // new_freq = turbo_freq
if (policy->cur != new_freq)
cpufreq_out_of_sync(policy, new_freq)
...
policy->cur = new_freq // cur = turbo_freq
..
__cpufreq_driver_target(policy->max)
cppc_set_perf(target) // policy->cur!=target

Reconfigure frequency to policy->max.

If policy->cur is not set to turbo_freq after two read operations, policy->cur will not be updated in cpufreq_verify_current_freq(), the execution path is as follows:
new_freq = cpufreq_driver->get() // new_freq == policy->cur
if (policy->cur != new_freq)
..
__cpufreq_driver_target(policy->max)
ret // policy->cur==target

Configured frequency will remain at turbo-freq.

When reading scaling_cur_freq, the frequency value that may be read is policy->cur. If arch does not implement arch_freq_get_on_cpu(), and the registered cpufreq_driver does not define setpolicy()/get(), the frequency will not be obtained through the get() and will directly feed back policy->cur. If the above problem occurs, no exception will be detected when reading scaling_cur_freq. But reading cpuinfo_cur_freq will reacquire the frequency through the get() interface and feedback the newly acquired frequency value.

Thanks
liwei


[1] https://docs.kernel.org/admin-guide/pm/cpufreq.html

...
policy->governor->limits()
__cpufreq_driver_target(policy->max)
if (policy->cur==target)
// generate error, keep set highest_perf
ret
cppc_set_perf(target)

Fix this by changing highest_perf to nominal_perf in cppc_cpufreq_cpu_init().

Fixes: 5477fb3bd1e8 ("ACPI / CPPC: Add a CPUFreq driver for use with CPPC")
Signed-off-by: liwei <liwei728@xxxxxxxxxx>
---
drivers/cpufreq/cppc_cpufreq.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/cpufreq/cppc_cpufreq.c b/drivers/cpufreq/cppc_cpufreq.c
index 64420d9cfd1e..db04a82b8a97 100644
--- a/drivers/cpufreq/cppc_cpufreq.c
+++ b/drivers/cpufreq/cppc_cpufreq.c
@@ -669,14 +669,14 @@ static int cppc_cpufreq_cpu_init(struct cpufreq_policy *policy)
if (caps->highest_perf > caps->nominal_perf)
boost_supported = true;
- /* Set policy->cur to max now. The governors will adjust later. */
- policy->cur = cppc_perf_to_khz(caps, caps->highest_perf);
- cpu_data->perf_ctrls.desired_perf = caps->highest_perf;
+ /* Set policy->cur to norm now. */
+ policy->cur = cppc_perf_to_khz(caps, caps->nominal_perf);
+ cpu_data->perf_ctrls.desired_perf = caps->nominal_perf;
ret = cppc_set_perf(cpu, &cpu_data->perf_ctrls);
if (ret) {
pr_debug("Err setting perf value:%d on CPU:%d. ret:%d\n",
- caps->highest_perf, cpu, ret);
+ caps->nominal_perf, cpu, ret);
goto out;
}
--
2.25.1

--
viresh