Re: [PATCH] Documentation: sound: Fix trailing whitespaces

[Abhinav Saxena]

Adding Shuah Khan<skhan@xxxxxxxxxxxxxxxxxxx> to cc.

-Abhinav.

On Wed, May 15, 2024 at 03:41:03AM +0000, Abhinav Saxena wrote:
> Remove trailing whitespace from sound/hd-audio/notes as reported by
> checkpatch. Removing trailing spaces improves consistency, and
> prevents Preventing potential merge conflicts due to whitespace
> differences. maintain a cleaner and more professional codebase.
> 
> Signed-off-by: Abhinav Saxena <xandfury@xxxxxxxxx>
> ---
>  Documentation/sound/hd-audio/notes.rst | 16 ++++++++--------
>  1 file changed, 8 insertions(+), 8 deletions(-)
> 
> diff --git a/Documentation/sound/hd-audio/notes.rst b/Documentation/sound/hd-audio/notes.rst
> index a9e35b1f87bd..ef6a4513cce7 100644
> --- a/Documentation/sound/hd-audio/notes.rst
> +++ b/Documentation/sound/hd-audio/notes.rst
> @@ -15,7 +15,7 @@ problem is broken BIOS, and the rest is the driver implementation.
>  This document explains the brief trouble-shooting and debugging
>  methods for the	HD-audio hardware.
>  
> -The HD-audio component consists of two parts: the controller chip and 
> +The HD-audio component consists of two parts: the controller chip and
>  the codec chips on the HD-audio bus.  Linux provides a single driver
>  for all controllers, snd-hda-intel.  Although the driver name contains
>  a word of a well-known hardware vendor, it's not specific to it but for
> @@ -81,7 +81,7 @@ the wake-up timing.  It wakes up a few samples before actually
>  processing the data on the buffer.  This caused a lot of problems, for
>  example, with ALSA dmix or JACK.  Since 2.6.27 kernel, the driver puts
>  an artificial delay to the wake up timing.  This delay is controlled
> -via ``bdl_pos_adj`` option. 
> +via ``bdl_pos_adj`` option.
>  
>  When ``bdl_pos_adj`` is a negative value (as default), it's assigned to
>  an appropriate value depending on the controller chip.  For Intel
> @@ -144,7 +144,7 @@ see a regression wrt the sound quality (stuttering, etc) or a lock-up
>  in the recent kernel, try to pass ``enable_msi=0`` option to disable
>  MSI.  If it works, you can add the known bad device to the blacklist
>  defined in hda_intel.c.  In such a case, please report and give the
> -patch back to the upstream developer. 
> +patch back to the upstream developer.
>  
>  
>  HD-Audio Codec
> @@ -375,7 +375,7 @@ HD-Audio Reconfiguration
>  ------------------------
>  This is an experimental feature to allow you re-configure the HD-audio
>  codec dynamically without reloading the driver.  The following sysfs
> -files are available under each codec-hwdep device directory (e.g. 
> +files are available under each codec-hwdep device directory (e.g.
>  /sys/class/sound/hwC0D0):
>  
>  vendor_id
> @@ -433,7 +433,7 @@ re-configure based on that state, run like below:
>  ::
>  
>      # echo 0x14 0x9993013f > /sys/class/sound/hwC0D0/user_pin_configs
> -    # echo 1 > /sys/class/sound/hwC0D0/reconfig  
> +    # echo 1 > /sys/class/sound/hwC0D0/reconfig
>  
>  
>  Hint Strings
> @@ -494,7 +494,7 @@ indep_hp (bool)
>      mixer control, if available
>  add_stereo_mix_input (bool)
>      add the stereo mix (analog-loopback mix) to the input mux if
> -    available 
> +    available
>  add_jack_modes (bool)
>      add "xxx Jack Mode" enum controls to each I/O jack for allowing to
>      change the headphone amp and mic bias VREF capabilities
> @@ -504,7 +504,7 @@ power_save_node (bool)
>      stream states
>  power_down_unused (bool)
>      power down the unused widgets, a subset of power_save_node, and
> -    will be dropped in future 
> +    will be dropped in future
>  add_hp_mic (bool)
>      add the headphone to capture source if possible
>  hp_mic_detect (bool)
> @@ -603,7 +603,7 @@ present.
>  
>  The patch module option is specific to each card instance, and you
>  need to give one file name for each instance, separated by commas.
> -For example, if you have two cards, one for an on-board analog and one 
> +For example, if you have two cards, one for an on-board analog and one
>  for an HDMI video board, you may pass patch option like below:
>  ::
>  
> -- 
> 2.34.1
>