Re: [PATCH v2 3/3] riscv: dts: thead: Enable I2C on the BeagleV-Ahead

[Emil Renner Berthing]

Thomas Bonnefille wrote:
> This commit enables the I2C0 controller of the TH1520, together with
> the FT24C32A EEPROM that is connected to it.
> In addition, this commit also enables the I2C controllers I2C2, I2C4
> and I2C5 as they are all three exposed on headers (P9 19 and 20 for I2C2,
> P9 17 and 18 for I2C5 and MikroBus 7 and 5 for I2C4).
> It also defined the required pinctrl nodes.
>
> Signed-off-by: Thomas Bonnefille <thomas.bonnefille@xxxxxxxxxxx>
> ---
>  arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts | 84 ++++++++++++++++++++++
>  1 file changed, 84 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> index 57a2578123eb..aeb04f5159d5 100644
> --- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> +++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> @@ -121,6 +121,47 @@ led-pins {
>  	};
>  };
>
> +&padctrl1_apsys {

These node references should be ordered alphabetically, so please put this
below &padctrl0_apsys.

> +	i2c0_pins: i2c0-0 {
> +		i2c-pins {
> +			pins = "I2C0_SDA",
> +			       "I2C0_SCL";
> +			function = "i2c";
> +			bias-pull-up = <2100>;

Are you sure the strong pull-up is needed here and below?

> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +
> +	i2c4_pins: i2c4-0 {
> +		i2c-pins {
> +			pins = "GPIO0_19", /*I2C4_SDA*/
> +			       "GPIO0_18"; /*I2C4_SCL*/

Please add spaces here like other kernel comments. Eg. /* I2C4_SDA */

> +			function = "i2c";
> +			bias-pull-up = <2100>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +
> +	i2c5_pins: i2c5-0 {
> +		i2c-pins {
> +			pins = "QSPI1_D0_MOSI", /*I2C5_SDA*/
> +			       "QSPI1_CSN0";    /*I2C5_SCL*/

Same here.

> +			function = "i2c";
> +			bias-pull-up = <2100>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +};
> +
>  &padctrl0_apsys {
>  	uart0_pins: uart0-0 {
>  		tx-pins {
> @@ -143,6 +184,19 @@ rx-pins {
>  			slew-rate = <0>;
>  		};
>  	};
> +
> +	i2c2_pins: i2c2-0 {

i2c2-0 sorts before uart0-0 alphabetically.

> +		i2c-pins {
> +			pins = "I2C2_SDA",
> +			       "I2C2_SCL";
> +			function = "i2c";
> +			bias-pull-up = <2100>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
>  };
>
>  &uart0 {
> @@ -150,3 +204,33 @@ &uart0 {
>  	pinctrl-0 = <&uart0_pins>;
>  	status = "okay";
>  };
> +
> +&i2c0 {

Again please sort these references alphabetically.

> +	status = "okay";

And the properties. Eg. move status below pinctrl-0.


> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins>;
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c32";
> +		reg = <0x50>;
> +	};
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins>;
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c4_pins>;
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c5_pins>;
> +};
>
> --
> 2.45.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-riscv