Re: [PATCH 2/2] arm64: dts: rockchip: Add CM3588 NAS board

From: Jonas Karlman
Date: Mon May 27 2024 - 15:03:47 EST

Next message: Krzysztof Kozlowski: "Re: [PATCH v2 1/2] media: dt-bindings: Add ST VD56G3 camera sensor binding"
Previous message: Jeff Johnson: "[PATCH] fs: bcachefs: add missing MODULE_DESCRIPTION()"
In reply to: Sebastian Kropatsch: "[PATCH 2/2] arm64: dts: rockchip: Add CM3588 NAS board"
Next in thread: Heiko Stübner: "Re: [PATCH 2/2] arm64: dts: rockchip: Add CM3588 NAS board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Sebastian,

On 2024-05-26 23:48, Sebastian Kropatsch wrote:
> The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
> the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
>
> Hardware features:
> - Rockchip RK3588 SoC
> - 4GB/8GB/16GB LPDDR4x RAM
> - 64GB eMMC
> - MicroSD card slot
> - 1x RTL8125B 2.5G Ethernet
> - 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs
> - 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A
> - 1x USB 3.0 Type-C with DP AltMode support
> - 2x HDMI 2.1 out, 1x HDMI in
> - MIPI-CSI Connector, MIPI-DSI Connector
> - 40-pin GPIO header
> - 4 buttons: power, reset, recovery, MASK, user button
> - 3.5mm Headphone out, 2.0mm PH-2A Mic in
> - 5V Fan connector, PWM buzzer, IR receiver, RTC battery connector
>
> PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1
> speed. Data lane mapping in the DT is done like described in commit
> f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588").
>
> This device tree includes support for eMMC, SD card, ethernet, all USB2
> and USB3 ports, all four M.2 slots, GPU, RTC, buzzer, UART debugging as
> well as the buttons and LEDs.
> The GPIOs are labeled according to the schematics.
>
> Signed-off-by: Sebastian Kropatsch <seb-dev@xxxxxx>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3588-cm3588-nas.dts | 1269 +++++++++++++++++
> 2 files changed, 1270 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-cm3588-nas.dts

Because the CM3588 is a SoM and the NAS is a carrier board this should
probably be split in two, cm3588.dtsi and cm3588-nas.dts.

>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index c544ff507d20..f1ff58bdf2cd 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-sige7.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-cm3588-nas.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-cm5-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-cm3588-nas.dts b/arch/arm64/boot/dts/rockchip/rk3588-cm3588-nas.dts
> new file mode 100644
> index 000000000000..6c45b376d001
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-cm3588-nas.dts
> @@ -0,0 +1,1269 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2023 FriendlyElec Computer Tech. Co., Ltd.
> + * Copyright (c) 2023 Thomas McKahan
> + * Copyright (c) 2024 Sebastian Kropatsch
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include <dt-bindings/usb/pd.h>
> +#include "rk3588.dtsi"
> +
> +/ {
> + model = "FriendlyElec CM3588 NAS";
> + compatible = "friendlyarm,cm3588-nas", "rockchip,rk3588";

Maybe this should be something like:

"friendlyarm,cm3588-nas", "friendlyarm,cm3588", "rockchip,rk3588";

> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc_keys: adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 1>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + button-vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <17000>;
> + };
> + };
> +
> + analog-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&headphone_detect>;
> +
> + simple-audio-card,name = "realtek,rt5616-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,hp-det-gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_LOW>;
> +
> + simple-audio-card,routing =
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "MIC1", "Microphone Jack",
> + "Microphone Jack", "micbias1";
> + simple-audio-card,widgets =
> + "Headphone", "Headphones",
> + "Microphone", "Microphone Jack";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s0_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rt5616>;
> + };
> + };
> +
> + fan: pwm-fan {
> + compatible = "pwm-fan";
> + #cooling-cells = <2>;
> + cooling-levels = <0 50 80 120 160 220>;
> + fan-supply = <&vcc_5v0_sys>;
> + pwms = <&pwm1 0 50000 0>;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&key1_pin>;
> +
> + button-user {
> + debounce-interval = <50>;
> + gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>;
> + label = "User Button";
> + linux,code = <BTN_1>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_sys: led-0 {
> + gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>;
> + label = "system-led";
> + linux,default-trigger = "heartbeat";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_sys_pin>;
> + };
> +
> + led_usr: led-1 {
> + gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> + label = "user-led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_usr_pin>;
> + };
> + };
> +
> + vcc_12v_dcin: vcc-12v-dcin-regulator {

Fixed regulators should use the recommended nodename, i.e. a regulator-
prefix.

> + compatible = "regulator-fixed";
> + regulator-name = "vcc_12v_dcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + /* vcc_5v0_sys powers the peripherals */
> + vcc_5v0_sys: vcc-5v0-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_12v_dcin>;
> + };
> +
> + vcc_5v0_host_20: vcc-5v0-host-20 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc_5v0_host20_en>;
> + regulator-name = "vcc_5v0_host_20";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v0_sys>;
> + };
> +
> + vcc_5v0_host_30: vcc-5v0-host-30 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;

Use the recommended gpios prop.

> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc_5v0_host30_en>;
> + regulator-name = "vcc_5v0_host_30";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v0_sys>;
> + };
> +
> + vcc_3v3_host_32: vcc-3v3-host-32-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc_3v3_host32_en>;
> + regulator-name = "vcc_3v3_host_32";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_5v0_sys>;
> + };
> +
> + vbus_5v0_typec: vbus-5v0-typec-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;

Same, use the recommended gpios prop.

> + pinctrl-names = "default";
> + pinctrl-0 = <&typec_5v_pwr_en>;
> + regulator-name = "vbus_5v0_typec";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v0_sys>;
> + };
> +
> + /* vcc_4v0_sys powers the RK806, RK860's */
> + vcc_4v0_sys: vcc-4v0-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_4v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <4000000>;
> + regulator-max-microvolt = <4000000>;
> + vin-supply = <&vcc_12v_dcin>;
> + };
> +
> + vcc_3v3_pcie20: vcc-3v3-pcie20-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3_pcie20";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_3v3_s3>;
> + };
> +
> + vcc_3v3_pcie30: vcc-3v3-pcie30-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3_pcie30";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_5v0_sys>;
> + };
> +
> + vcc_3v3_sd_s0: vcc-3v3-sd-s0-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sd_s0_pwr>;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc_3v3_sd_s0";
> + vin-supply = <&vcc_3v3_s3>;
> + };
> +
> + vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-1v1-nldo-s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + vin-supply = <&vcc_4v0_sys>;
> + };
> +};
> +
> +&combphy0_ps {
> + status = "okay";
> +};
> +
> +&combphy1_ps {
> + status = "okay";
> +};
> +
> +&combphy2_psu {
> + status = "okay";
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b2 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +&cpu_b3 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +/* GPIO names are in the format "Human-readable-name [SIGNAL_LABEL]" */
> +/* Signal labels match the official CM3588 NAS schematic revision 2309 */
> +&gpio0 {
> + gpio-line-names =
> + /* GPIO0 A0-A7 */
> + "", "", "", "",
> + "MicroSD detect [SDMMC_DET_L]", "", "", "",
> + /* GPIO0 B0-B7 */
> + "", "", "", "",
> + "", "", "", "",
> + /* GPIO0 C0-C7 */
> + "", "", "", "",
> + "Pin 10 [UART0_RX_M0]", "Pin 08 [UART0_TX_M0/PWM4_M0]", "Pin 32 [PWM5_M1]", "",
> + /* GPIO0 D0-D7 */
> + "", "", "", "USB3 Type-C [CC_INT_L]",
> + "IR sensor [PWM3_IR_M0]", "User Button", "", "";
> +};
> +
> +&gpio1 {
> + gpio-line-names =
> + /* GPIO1 A0-A7 */
> + "Pin 27 [UART6_RX_M1]", "Pin 28 [UART6_TX_M1]", "", "",
> + "USB2 Type-A [USB2_PWREN]", "", "", "Pin 15",
> + /* GPIO1 B0-B7 */
> + "Pin 26", "Pin 21 [SPI0_MISO_M2]", "Pin 19 [SPI0_MOSI_M2/UART4_RX_M2]", "Pin 23 [SPI0_CLK_M2/UART4_TX_M2]",
> + "Pin 24 [SPI0_CS0_M2/UART7_RX_M2]", "Pin 22 [SPI0_CS1_M0/UART7_TX_M2]", "", "CSI-Pin 14 [MIPI_CAM2_CLKOUT]",
> + /* GPIO1 C0-C7 */
> + "", "", "", "",
> + "Headphone detect [HP_DET_L]", "", "", "",
> + /* GPIO1 D0-D7 */
> + "", "", "[TYPEC5V_PW REN_H]", "5V Fan [PWM1_M1]",
> + "", "HDMI-in detect[HDMIIRX_DET_L]", "Pin 05 [I2C8_SCL_M2]", "Pin 03 [I2C8_SDA_M2]";
> +};
> +
> +&gpio2 {
> + gpio-line-names =
> + /* GPIO2 A0-A7 */
> + "", "", "", "",
> + "", "", "SPI NOR Flash [FSPI_D0_M1]", "SPI NOR Flash [FSPI_D1_M1]",
> + /* GPIO2 B0-B7 */
> + "SPI NOR Flash [FSPI_D2_M1]", "SPI NOR Flash [FSPI_D3_M1]", "", "SPI NOR Flash [FSPI_CLK_M1]",
> + "SPI NOR Flash [FSPI_CSN0_M1]", "", "", "",
> + /* GPIO2 C0-C7 */
> + "", "CSI-Pin 11 [MIPI_CAM2_RESET_L]", "CSI-Pin 12 [MIPI_CAM2_PDN_L]", "",
> + "", "", "", "",
> + /* GPIO2 D0-D7 */
> + "", "", "", "",
> + "", "", "", "";
> +};
> +
> +&gpio3 {
> + gpio-line-names =
> + /* GPIO3 A0-A7 */
> + "Pin 35 [SPI4_MISO_M1/PW M10_M0]", "Pin 38 [SPI4_MOSI_M1]", "Pin 40 [SPI4_CLK_M1/UART8_TX_M1]", "Pin 36 [SPI4_CS0_M1/UART8_RX_M1]",
> + "Pin 37 [SPI4_CS1_M1]", "USB3 Type-A Port 2 [USB3_2_PWREN]", "DSI-Pin 12 [LCD_RST]", "Buzzer [PW M8_M0]",
> + /* GPIO3 B0-B7 */
> + "Pin 33 [PW M9_M0]", "DSI-Pin 10 [PW M2_M1/LCD_BL]", "Pin 07", "Pin 16",
> + "Pin 18", "Pin 29 [UART3_TX_M1/PW M12_M0]", "Pin 31 [UART3_RX_M1/PW M13_M0]", "Pin 12",
> + /* GPIO3 C0-C7 */
> + "DSI-Pin 08 [TP_INT_L]", "DSI-Pin 14 [TP_RST_L]", "Pin 11 [PWM14_M0]", "Pin 13 [PWM15_IR_M0]",
> + "", "", "", "DSI-Pin 06 [I2C5_SCL_M0_TP]",
> + /* GPIO3 D0-D7 */
> + "DSI-Pin 05 [I2C5_SDA_M0_TP]", "", "", "",
> + "", "", "", "";
> +};
> +
> +&gpio4 {
> + gpio-line-names =
> + /* GPIO4 A0-A7 */
> + "", "", "M.2 M-Key Socket 4 [M2_D_PERST_L]", "",
> + "", "", "", "",
> + /* GPIO4 B0-B7 */
> + "USB3 Type-A Port 1 [USB3_TYPEC1_PWREN]", "", "", "M.2 M-Key Socket 3 [M2_C_PERST_L]",
> + "M.2 M-Key Socket 2 [M2_B_PERST_L]", "M.2 M-Key Socket 1 [M2_A_CLKREQ_L]", "M.2 M-Key Socket 1 [M2_A_PERST_L]", "",
> + /* GPIO4 C0-C7 */
> + "", "", "", "",
> + "", "", "", "",
> + /* GPIO4 D0-D7 */
> + "", "", "", "",
> + "", "", "", "";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu_s0>;
> + sram-supply = <&vdd_gpu_mem_s0>;
> + status = "okay";
> +};
> +
> +&hdptxphy_hdmi0 {
> + status = "okay";

HDMI support is not ready for RK3588 and no other board enable the HDMI
PHY yet, maybe wait with this?

> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0m2_xfer>;
> + status = "okay";
> +
> + vdd_cpu_big0_s0: regulator@42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big0_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc_4v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_big1_s0: regulator@43 {
> + compatible = "rockchip,rk8603", "rockchip,rk8602";
> + reg = <0x43>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big1_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc_4v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + vdd_npu_s0: regulator@42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_npu_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc_4v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4m3_xfer>;
> + status = "disabled";
> +};
> +
> +/* Connected to MIPI-DSI0 */
> +&i2c5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c5m0_xfer>;
> + status = "disabled";
> +};
> +
> +&i2c6 {
> + clock-frequency = <200000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c6m0_xfer>;
> + status = "okay";
> +
> + fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-0 = <&usbc0_int>;
> + pinctrl-names = "default";
> + vbus-supply = <&vbus_5v0_typec>;
> +
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + data-role = "dual";
> + label = "USB-C";
> + op-sink-microwatt = <1000000>;
> + power-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + try-power-role = "sink";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usbc0_orien_sw: endpoint {
> + remote-endpoint = <&usbdp_phy0_orientation_switch>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usbc0_role_sw: endpoint {
> + remote-endpoint = <&dwc3_0_role_switch>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + dp_altmode_mux: endpoint {
> + remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
> + };
> + };
> + };
> + };
> + };
> +
> + hym8563: rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-output-names = "hym8563";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hym8563_int>;
> + wakeup-source;
> + };
> +};
> +
> +/* Connected to MIPI-CSI1 */
> +&i2c7 {
> + clock-frequency = <200000>;
> + status = "okay";
> +
> + rt5616: audio-codec@1b {
> + compatible = "realtek,rt5616";
> + reg = <0x1b>;
> + #sound-dai-cells = <0>;
> + };
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&i2c8 {
> + pinctrl-0 = <&i2c8m2_xfer>;
> + status = "okay";
> +};
> +
> +&i2s0_8ch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s0_lrck
> + &i2s0_mclk
> + &i2s0_sclk
> + &i2s0_sdi0
> + &i2s0_sdo0>;
> + status = "okay";
> +};
> +
> +&i2s5_8ch {
> + status = "okay";
> +};
> +
> +&i2s6_8ch {
> + status = "okay";
> +};
> +
> +&i2s7_8ch {
> + status = "okay";
> +};
> +
> +&pcie2x1l0 {
> + /* 2. M.2 slot, CON14: pcie30phy port0 lane1, @fe170000 */
> + max-link-speed = <3>;
> + num-lanes = <1>;
> + phys = <&pcie30phy>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie2_0_rst>;
> + reset-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc_3v3_pcie30>;
> + status = "okay";
> +};
> +
> +&pcie2x1l1 {
> + /* 4. M.2 slot, CON16: pcie30phy port1 lane1, @fe180000 */
> + max-link-speed = <3>;
> + num-lanes = <1>;
> + phys = <&pcie30phy>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie2_1_rst>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc_3v3_pcie30>;
> + status = "okay";
> +};
> +
> +&pcie2x1l2 {
> + /* r8125 ethernet, @fe190000 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie2_2_rst>;
> + reset-gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc_3v3_pcie20>;
> + status = "okay";
> +};
> +
> +&pcie30phy {
> + /*
> + * Data lane mapping <1 3 2 4> = x1x1 x1x1 (bifurcation of both ports)
> + * port 0 lane 0 - always mapped to controller 0 (4L)
> + * port 0 lane 1 - map to controller 2 (1L0)
> + * port 1 lane 0 - map to controller 1 (2L)
> + * port 1 lane 1 - map to controller 3 (1L1)
> + */
> + data-lanes = <1 3 2 4>;
> + status = "okay";
> +};
> +
> +&pcie3x4 {
> + /* 1. M.2 slot, CON13: pcie30phy port0 lane0, @fe150000 */
> + max-link-speed = <3>;
> + num-lanes = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie3x4_rst>;
> + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc_3v3_pcie30>;
> + status = "okay";
> +};
> +
> +&pcie3x2 {
> + /* 3. M.2 slot, CON15: pcie30phy port1 lane0, @fe160000 */
> + max-link-speed = <3>;
> + num-lanes = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie3x2_rst>;
> + reset-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc_3v3_pcie30>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + audio {
> + headphone_detect: headphone-detect {
> + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + gpio-key {
> + key1_pin: key1-pin {
> + rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + gpio-leds {
> + led_sys_pin: led-sys-pin {
> + rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + led_usr_pin: led-usr-pin {
> + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + hym8563 {
> + hym8563_int: hym8563-int {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + pcie {
> + pcie2_0_rst: pcie2-0-rst {
> + rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie2_1_rst: pcie2-1-rst {
> + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie2_2_rst: pcie2-2-rst {
> + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie3x2_rst: pcie3x2-rst {
> + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie3x4_rst: pcie3x4-rst {
> + rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + sd_s0_pwr: sd-s0-pwr {
> + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + usb {
> + vcc_5v0_host20_en: vcc-5v0-host20-en {
> + rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + vcc_5v0_host30_en: vcc-5v0-host30-en {
> + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + vcc_3v3_host32_en: vcc-3v3-host32-en {
> + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb-typec {
> + usbc0_int: usbc0-int {
> + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + typec_5v_pwr_en: typec-5v-pwr-en {
> + rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +/* Connected to 5V Fan */
> +&pwm1 {
> + pinctrl-0 = <&pwm1m1_pins>;

pinctrl-names is missing, should typically always be defined together
with pinctrl-X props, same for multiple nodes.

> + status = "okay";
> +};
> +
> +/* Connected to MIPI-DSI0 */
> +&pwm2 {
> + pinctrl-0 = <&pwm2m1_pins>;
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&pwm5 {
> + pinctrl-0 = <&pwm5m1_pins>;
> + status = "okay";
> +};
> +
> +/* GPIO Connector */
> +&pwm8 {
> + pinctrl-0 = <&pwm8m0_pins>;
> + status = "okay";
> +};
> +
> +/* GPIO Connector */
> +&pwm9 {
> + pinctrl-0 = <&pwm9m0_pins>;
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&avcc_1v8_s0>;
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&sdhci {
> + bus-width = <8>;
> + full-pwr-cycle-in-suspend;

Is this really necessary?

> + mmc-hs400-1_8v;
> + mmc-hs400-enhanced-strobe;
> + no-sd;
> + no-sdio;
> + non-removable;
> + status = "okay";
> +};
> +
> +/* microSD card */
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;

Should not be needed because of no-mmc.

> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;

Please drop, not needed with sdmmc_det pinctrl being used.

> + disable-wp;
> + max-frequency = <150000000>;
> + no-mmc;
> + no-sdio;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3_sd_s0>;
> + vqmmc-supply = <&vccio_sd_s0>;
> + status = "okay";
> +};
> +
> +/* GPIO Connector */
> +&spi0 {
> + num-cs = <1>;
> + pinctrl-0 = <&spi0m2_cs0 &spi0m2_pins>;
> + status = "disabled";
> +};
> +
> +&spi2 {
> + status = "okay";
> + assigned-clocks = <&cru CLK_SPI2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
> + num-cs = <1>;
> +
> + rk806_single: pmic@0 {
> + compatible = "rockchip,rk806";
> + reg = <0x0>;
> +
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> +
> + spi-max-frequency = <1000000>;
> +
> + system-power-controller;
> +
> + vcc1-supply = <&vcc_4v0_sys>;
> + vcc2-supply = <&vcc_4v0_sys>;
> + vcc3-supply = <&vcc_4v0_sys>;
> + vcc4-supply = <&vcc_4v0_sys>;
> + vcc5-supply = <&vcc_4v0_sys>;
> + vcc6-supply = <&vcc_4v0_sys>;
> + vcc7-supply = <&vcc_4v0_sys>;
> + vcc8-supply = <&vcc_4v0_sys>;
> + vcc9-supply = <&vcc_4v0_sys>;
> + vcc10-supply = <&vcc_4v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc_4v0_sys>;
> + vcc13-supply = <&vcc_1v1_nldo_s3>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc_4v0_sys>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + rk806_dvs1_null: dvs1-null-pins {
> + pins = "gpio_pwrctrl1";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs2_null: dvs2-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs3_null: dvs3-null-pins {
> + pins = "gpio_pwrctrl3";
> + function = "pin_fun0";
> + };
> +
> + regulators {
> + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_s0";
> + regulator-enable-ramp-delay = <400>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_cpu_lit_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_log_s0: dcdc-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_log_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_ddr_s0: dcdc-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <900000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_ddr_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + vdd2_ddr_s3: dcdc-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd2_ddr_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_2v0_pldo_s3: dcdc-reg7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_2v0_pldo_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2000000>;
> + };
> + };
> +
> + vcc_3v3_s3: dcdc-reg8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_3v3_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vddq_ddr_s0: dcdc-reg9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vddq_ddr_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8_s3: dcdc-reg10 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avcc_1v8_s0: pldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "avcc_1v8_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8_s0: pldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avdd_1v2_s0: pldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "avdd_1v2_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v3_s0: pldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_3v3_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd_s0: pldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vccio_sd_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + pldo6_s3: pldo-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "pldo6_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_0v75_s3: nldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "vdd_0v75_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_ddr_pll_s0: nldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_ddr_pll_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + avdd_0v75_s0: nldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "avdd_0v75_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v85_s0: nldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_0v85_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v75_s0: nldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "vdd_0v75_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&spi4 {
> + num-cs = <1>;
> + pinctrl-0 = <&spi4m1_cs0 &spi4m1_pins>;
> + status = "disabled";
> +};
> +
> +&tsadc {
> + status = "okay";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart0 {
> + pinctrl-0 = <&uart0m0_xfer>;
> + status = "disabled";
> +};
> +
> +/* Debug UART */
> +&uart2 {
> + pinctrl-0 = <&uart2m0_xfer>;
> + status = "okay";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart3 {
> + pinctrl-0 = <&uart3m1_xfer>;
> + status = "disabled";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart4 {
> + pinctrl-0 = <&uart4m2_xfer>;
> + status = "disabled";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart6 {
> + pinctrl-0 = <&uart6m1_xfer>;
> + status = "okay";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart7 {
> + pinctrl-0 = <&uart7m2_xfer>;
> + status = "disabled";
> +};
> +
> +/* GPIO Connector, connected to 40-pin GPIO header */
> +&uart8 {
> + pinctrl-0 = <&uart8m1_xfer>;
> + status = "disabled";
> +};
> +
> +&u2phy0 {
> + status = "okay";
> +};
> +
> +&u2phy0_otg {
> + status = "okay";
> +};
> +
> +&u2phy1 {
> + status = "okay";
> +};
> +
> +&u2phy1_otg {
> + phy-supply = <&vcc_5v0_host_30>;
> + status = "okay";
> +};
> +
> +&u2phy2 {
> + status = "okay";
> +};
> +
> +&u2phy2_host {
> + phy-supply = <&vcc_5v0_host_20>;
> + status = "okay";
> +};
> +
> +&u2phy3 {
> + status = "okay";
> +};
> +
> +&u2phy3_host {
> + phy-supply = <&vcc_3v3_host_32>;
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host0_xhci {
> + dr_mode = "otg";

This is already default dr_mode for usb_host0_xhci.

> + usb-role-switch;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dwc3_0_role_switch: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&usbc0_role_sw>;
> + };
> + };
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
> +
> +/* Upper USB 3.0 port */
> +&usb_host1_xhci {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +/* Lower USB 3.0 port */
> +&usb_host2_xhci {
> + dr_mode = "host";

This is already default dr_mode for usb_host2_xhci.

> + status = "okay";
> +};
> +
> +&usbdp_phy0 {
> + orientation-switch;
> + sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
> + sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usbdp_phy0_orientation_switch: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&usbc0_orien_sw>;
> + };
> +
> + usbdp_phy0_dp_altmode_mux: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&dp_altmode_mux>;
> + };
> + };
> +};
> +
> +&usbdp_phy1 {
> + status = "okay";
> +};
> +
> +&vop {
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};

vop and vop_mmu node can probably be skipped for now.

Regards,
Jonas

> +
> +&wdt {
> + status = "okay";
> +};
> --
> 2.43.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Next message: Krzysztof Kozlowski: "Re: [PATCH v2 1/2] media: dt-bindings: Add ST VD56G3 camera sensor binding"
Previous message: Jeff Johnson: "[PATCH] fs: bcachefs: add missing MODULE_DESCRIPTION()"
In reply to: Sebastian Kropatsch: "[PATCH 2/2] arm64: dts: rockchip: Add CM3588 NAS board"
Next in thread: Heiko Stübner: "Re: [PATCH 2/2] arm64: dts: rockchip: Add CM3588 NAS board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]