Re: iio: iio-trig-hrtimer bug on suspend/resume when used with bmi160 and bmi323

[Jonathan Cameron]

On Thu, 30 May 2024 16:07:22 +0200
Denis Benato <benato.denis96@xxxxxxxxx> wrote:

> On 1/15/24 10:37, Jonathan Cameron wrote:
> > On Sun, 14 Jan 2024 21:04:12 +0100
> > Denis Benato <benato.denis96@xxxxxxxxx> wrote:
> >   
> >> On 1/13/24 18:46, Jonathan Cameron wrote:  
> >>> On Wed, 10 Jan 2024 23:35:01 +0100
> >>> Denis Benato <benato.denis96@xxxxxxxxx> wrote:
> >>>     
> >>>> Hello,
> >>>>
> >>>> With this mail I am submitting bug report that is probably related to
> >>>> iio-trig-hrtimer but there is also the possibility for it to be
> >>>> specific to bmi160 and bmi323.
> >>>>
> >>>> The described problem have been reproduced on my handheld PC (Asus
> >>>> RC71L) and in another handheld PC with two different gyroscope
> >>>> drivers: bmi323 (backported by me on v6.7, on RC71L) and bmi160.
> >>>>
> >>>> My target hardware (RC71L that yeld to this discovery) has a bmi323
> >>>> chip that does not have any interrupt pins reaching the CPU, yet I
> >>>> need to fetch periodically data from said device, therefore I used
> >>>> iio-trig-hrtimer: created a trigger, set the device and trigger
> >>>> sampling frequencies, bound the trigger to the device and enabled
> >>>> buffer: data is being read and available over /dev/iio:device0.
> >>>>
> >>>> While in this state if I suspend my handheld I receive (from dmesg)
> >>>> the warning reported below and at resume data is not coming out of
> >>>> the iio device and the hrtimer appears to not be working. If I create
> >>>> a new trigger and bind the new trigger to said iio device and
> >>>> re-enable buffer data does come out of /dev/iio:device0 once more,
> >>>> until the next sleep.
> >>>>
> >>>> Since this is important to me I have taken the time to look at both
> >>>> drivers and iio-trig-hrtimer and I have identified three possible
> >>>> reasons:
> >>>>
> >>>> 1) iio-trig-hrtimer won't work after suspend regardless of how it is
> >>>> used (this is what I believe is the cause)    
> >>> me too.    
> >> who and how should investigate this issue? Would putting a kprintf in the hrtimer callback be enough to check?  
> > The warning you have pretty much points at this being the problem, but sure
> > you could add a print there to be absolutely sure.
> >   
> >>
> >>
> >> Just to make sure I understood correctly: is this a separate issue from the warning I receive or are those linked?  
> > 
> > I think it's all one issue.  
> Hello,
> 
> Sorry for the delay, I was able to find some time just recently.
> 
> Sadly I don't think anymore this is just one issue:
> 
> I have setup a proof of concept that at suspend sets a boolean to true and at resume sets the same boolean to false, and on trigger_handler returns IRQ_NONE if the device is sleeping (everything guarded by an additional mutex) and it solved the warning: no more regmap access are being performed after the device is put to sleep, but unfortunately the acquisition does not automatically resume after waking up the device.
> 
> How shall we proceed?

It's been a while (and a busy day of reviewing) so I'm struggling
a bit with the best away forwards.

A hackyish approach might be to mask the interrupt at device side
(fake interrupt used as part of the tree from a trigger to a pollfunc).
A tidy wrapped up version of this might be the best route forwards
though it won't currently stop the hrtimer merrily poking interrupts
at no one

As a hack, could you try having your suspend call disable_irq() on
the irq found in iio_dev->poll_func->irq and reenable it in resume?
That might be sufficient.

Check poll_func goes somewhere first though and that irq is > 0
I think that will call iio_trig_subirq_mask() which should block
any further interrupts until it's unmasked again.

We'll need to ensure this doesn't race with pollfunc going away though
which will make it more complex, but the above test should tell us
if there is a fairly smooth path to making this work.

I'll try and find time to do some testing myself, but it won't be
for a few weeks :(

Thanks,

Jonathan


> >   
> >>>     
> >>>> 2) iio-trig-hrtimer is stopped by the -ESHTDOWN returned by the
> >>>> function printing "Transfer while suspended", however that stack
> >>>> trace does not include function calls related to iio-trig-hrtimer and
> >>>> this seems less plausible 3) bmi160 and bmi323 appears to be similar
> >>>> and maybe are sharing a common bug with suspend (this is also why I
> >>>> have maintainers of those drivers in the recipient list)
> >>>>
> >>>> Thanks for your time, patience and understanding,    
> >>>
> >>> Hi Denis,
> >>>
> >>> I suspect this is the legacy of the platform I used to test the hrtimer
> >>> and similar triggers on never had working suspend and resume (we ripped
> >>> support for that board out of the kernel a while back now...)
> >>> Hence those paths were never tested by me and others may not have cared
> >>> about this particular case.
> >>>
> >>> Anyhow, so I think what is going on is fairly simple.
> >>>
> >>> There is no way for a driver to indicate to a trigger provided by a separate
> >>> module / hardware device that it should stop triggering data capture.
> >>> The driver in question doesn't block data capture when suspended, which
> >>> would be easy enough to add but doesn't feel like the right solution.
> >>>
> >>> So my initial thought is that we should add suspend and resume callbacks to
> >>> iio_trigger_ops and call them manually from iio device drivers in their
> >>> suspend and resume callbacks.  These would simply pause whatever the
> >>> trigger source was so that no attempts are made to trigger the use of
> >>> the device when it is suspended.
> >>>
> >>> It gets a little messy though as triggers can be shared between
> >>> multiple devices so we'd need to reference count suspend and resume
> >>> for the trigger to make sure we only resume once all consumers of
> >>> the trigger have said they are ready to cope with triggers again.
> >>>
> >>> As mentioned, the alternative would be to block the triggers at ingress
> >>> to the bmi323 and bmi160 drivers.  There may be a helpful pm flag that could
> >>> be used but if not, then setting an is_suspended flag under the data->mutex
> >>> to avoid races. and reading it in the trigger_handler to decide whether
> >>> to talk to the device should work.    
> >> I was thinking of doing this too, but I don't know if adding a mutex to frequently invoked functions is going to introduce some timing problems and so I was waiting for some comments on that matter. If nothing bad is expected I can surely try it.  
> >>>
> >>> I'd kind of like the generic solution of actually letting the trigger
> >>> know, but not sure how much work it would turn out to be.  Either way there
> >>> are a lot of drivers to fix this problem in as in theory most triggers can
> >>> be used with most drivers that support buffered data capture.
> >>> There may also be fun corners where a hardware trigger from one IIO
> >>> device A is being used by another B and the suspend timing is such that B
> >>> finishing with the trigger results in A taking an action (in the try_reenable
> >>> callback) that could result in bus traffic.
> >>> That one is going to be much more fiddly to handle than the simpler case
> >>> you have run into.    
> >> Since more and more handheld PCs are coming and provided many vendors such as
> >> asus tends to improve what they did built on previous generations I think a
> >> general solution would be desirable.
> >>
> >> Plus there are handheld PCs that does not yet have a driver (bmi270) or are
> >> using an existing one and it would be very difficult to fix it in every of
> >> them as of now, in the future I fear it will become almost impossible or 
> >> extremely time consuming as market expands.  
> > 
> > Both solutions require specific calls to be added to every driver that might
> > encounter this - so most drivers that support triggers other than the ones
> > they supply.
> >   
> >>>
> >>> Thanks for the detailed bug report btw.   To get it fixed a few
> >>> questions:
> >>> 1) Are you happy to test proposed fixes?
> >>> 2) Do you want to have a go at fixing it yourself? (I'd suggest trying
> >>>    the fix in the bmi323 driver first rather than looking at the other 
> >>>    solution)
> >>>    If we eventually implement the more general version, then a bmi323
> >>>    additional protection against this problem would not be a problem.
> >>>
> >>> Clearly I'd like the answers to be yes to both questions, but up to you!
> >>>
> >>> Jonathan
> >>>
> >>>     
> >> Hello Jonathan and thank you kindly for you answer,
> >>
> >> I am very interested in the iio ecosystem as in those aforementioned
> >> handheld PCs the gyroscope plays the role as a mouse so it's a pretty
> >> important input device.
> >>
> >> I am writing to lkml not just as a single developer, but as part of a
> >>  larger community in this matter: this means we will be able to test
> >> any solution and in more than just one hardware.
> >>
> >> To answers your questions:
> >> 1) yes, we all will be very happy to
> >> 2) as I am very busy right now I might be unable to do that immediately,
> >> but I will surely do it if one general solution cannot be found or is impractical.
> >>
> >> As of my limited knowledge the number of drivers now existing that are affected
> >> are 2, and the number of drivers that will be affected, once the driver is
> >> written, will be at least 3.  
> > 
> > The problem appears to be general unfortunately.
> > 
> > I'll have to see if I can fire up something where I can actually test solutions
> > and I'm afraid I also don't have a lot of time at the moment.
> > Perhaps I can find time in the next few weeks to hack together a prototype
> > for one of the drivers you can test.
> > 
> > Jonathan
> >   
> >>
> >> Thank you very much for your answer,
> >> Denis
> >>  
> >   
> 
> Thank you for you time and patience,
> Denis