Re: kswapd0: page allocation failure: order:0, mode:0x820(GFP_ATOMIC), nodemask=(null),cpuset=/,mems_allowed=0 (Kernel v6.5.9, 32bit ppc)

[Erhard Furtner]

On Sat, 1 Jun 2024 00:01:48 -0600
Yu Zhao <yuzhao@xxxxxxxxxx> wrote:

> Hi Erhard,
> 
> The OOM kills on both kernel versions seem to be reasonable to me.
> 
> Your system has 2GB memory and it uses zswap with zsmalloc (which is
> good since it can allocate from the highmem zone) and zstd/lzo (which
> doesn't matter much). Somehow -- I couldn't figure out why -- it
> splits the 2GB into a 0.25GB DMA zone and a 1.75GB highmem zone:
> 
> [    0.000000] Zone ranges:
> [    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
> [    0.000000]   Normal   empty
> [    0.000000]   HighMem  [mem 0x0000000030000000-0x000000007fffffff]
> 
> The kernel can't allocate from the highmem zone -- only userspace and
> zsmalloc can. OOM kills were due to the low memory conditions in the
> DMA zone where the kernel itself failed to allocate from.
> 
> Do you know a kernel version that doesn't have OOM kills while running
> the same workload? If so, could you send that .config to me? If not,
> could you try disabling CONFIG_HIGHMEM? (It might not help but I'm out
> of ideas at the moment.)
> 
> Thanks!

Hi Yu!

Thanks for looking into this.

The reason for this 0.25GB DMA / 1.75GB highmem split is beyond my knowledge. I can only tell this much that it's like this at least since kernel v4.14.x (dmesg of an old bugreport of mine at https://bugzilla.kernel.org/show_bug.cgi?id=201723), I guess earlier kernel versions too.

Without CONFIG_HIGHMEM the memory layout looks like this:

Total memory = 768MB; using 2048kB for hash table
[...]
Top of RAM: 0x30000000, Total RAM: 0x30000000
Memory hole size: 0MB
Zone ranges:
  DMA      [mem 0x0000000000000000-0x000000002fffffff]
  Normal   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x0000000000000000-0x000000002fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000002fffffff]
percpu: Embedded 29 pages/cpu s28448 r8192 d82144 u118784
pcpu-alloc: s28448 r8192 d82144 u118784 alloc=29*4096
pcpu-alloc: [0] 0 [0] 1 
Kernel command line: ro root=/dev/sda5 slub_debug=FZP page_poison=1 netconsole=6666@192.168.2.8/eth0,6666@192.168.2.3/A8:A1:59:16:4F:EA debug 
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
Built 1 zonelists, mobility grouping on.  Total pages: 194880
mem auto-init: stack:all(pattern), heap alloc:off, heap free:off
Kernel virtual memory layout:
  * 0xffbdf000..0xfffff000  : fixmap
  * 0xff8f4000..0xffbdf000  : early ioremap
  * 0xf1000000..0xff8f4000  : vmalloc & ioremap
  * 0xb0000000..0xc0000000  : modules
Memory: 761868K/786432K available (7760K kernel code, 524K rwdata, 4528K rodata, 1100K init, 253K bss, 24564K reserved, 0K cma-reserved)
[...]

With only 768 MB RAM and 2048K hashtable I get pretty much the same "kswapd0: page allocation failure: order:0, mode:0xcc0(GFP_KERNEL),nodemask=(null),cpuset=/,mems_allowed=0" as with the HIGHMEM enabled kernel at
running "stress-ng --vm 2 --vm-bytes 1930M --verify -v".

I tried the workload on v6.6.32 LTS where the issue shows up too. But v6.1.92 LTS seems ok! Triple checked v6.1.92 to be sure.

Attached please find kernel v6.9.3 dmesg (without HIGHMEM) and kernel v6.1.92 .config.

Regards,
Erhard

Attachment: dmesg_693_g4_highmem-disabled
Description: Binary data

Attachment: config_6192_g4
Description: Binary data