[PATCH 2/2] arm64: dts: microchip: sparx5_pcb135: move non-MMIO nodes out of axi

[Krzysztof Kozlowski]

simple-bus nodes, so the "axi" node, should not have non-MMIO children
as pointed out by simple-bus schema dtbs_check:

  sparx5_pcb135_emmc.dtb: axi@600000000: sfp-eth60: {'compatible': ... should not be valid under {'type': 'object'}
    from schema $id: http://devicetree.org/schemas/simple-bus.yaml#

Reported-by: Rob Herring <robh@xxxxxxxxxx>
Closes: https://lore.kernel.org/all/CAL_Jsq+PtL3HTKkA_gwTjb_i1mFZ+wW+qwin34HMYmwW7oNDFw@xxxxxxxxxxxxxx/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
 .../dts/microchip/sparx5_pcb135_board.dtsi    | 95 +++++++++----------
 1 file changed, 47 insertions(+), 48 deletions(-)

diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index af2f1831f07f..196868898f49 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -13,6 +13,13 @@ gpio-restart {
 		priority = <200>;
 	};
 
+	i2c0_imux: i2c-mux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		led-0 {
@@ -56,6 +63,46 @@ led-7 {
 			default-state = "off";
 		};
 	};
+
+	sfp_eth60: sfp-eth60 {
+		compatible	 = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp_eth61: sfp-eth61 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp_eth62: sfp-eth62 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp_eth63: sfp-eth63 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp4>;
+		tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &gpio {
@@ -119,15 +166,6 @@ &sgpio2 {
 	microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
 };
 
-&axi {
-	i2c0_imux: i2c-mux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-parent = <&i2c0>;
-	};
-};
-
 &i2c0_imux {
 	pinctrl-names =
 		"i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
@@ -159,45 +197,6 @@ i2c_sfp4: i2c@3 {
 	};
 };
 
-&axi {
-	sfp_eth60: sfp-eth60 {
-		compatible	 = "sff,sfp";
-		i2c-bus = <&i2c_sfp1>;
-		tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
-		rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
-		los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
-	};
-	sfp_eth61: sfp-eth61 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c_sfp2>;
-		tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
-		rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
-		los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
-	};
-	sfp_eth62: sfp-eth62 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c_sfp3>;
-		tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
-		rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
-		los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
-	};
-	sfp_eth63: sfp-eth63 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c_sfp4>;
-		tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
-		rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
-		los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
-	};
-};
-
 &mdio0 {
 	status = "okay";
 	phy0: ethernet-phy@0 {
-- 
2.43.0