[PATCH v6 9/9] iio: adc: ad7173: Add support for AD411x devices

[Dumitru Ceclan via B4 Relay]

From: Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>

Add support for AD4111/AD4112/AD4114/AD4115/AD4116.

The AD411X family encompasses a series of low power, low noise, 24-bit,
sigma-delta analog-to-digital converters that offer a versatile range of
specifications.

This family of ADCs integrates an analog front end suitable for processing
both fully differential and single-ended, bipolar voltage inputs
addressing a wide array of industrial and instrumentation requirements.

- All ADCs have inputs with a precision voltage divider with a division
  ratio of 10.
- AD4116 has 5 low level inputs without a voltage divider.
- AD4111 and AD4112 support current inputs (0 mA to 20 mA) using a 50ohm
  shunt resistor.

Signed-off-by: Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>
---
 drivers/iio/adc/ad7173.c | 317 ++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 285 insertions(+), 32 deletions(-)

diff --git a/drivers/iio/adc/ad7173.c b/drivers/iio/adc/ad7173.c
index 58da5717fd36..cfcd12447e24 100644
--- a/drivers/iio/adc/ad7173.c
+++ b/drivers/iio/adc/ad7173.c
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * AD717x family SPI ADC driver
+ * AD717x and AD411x family SPI ADC driver
  *
  * Supported devices:
+ *  AD4111/AD4112/AD4114/AD4115/AD4116
  *  AD7172-2/AD7172-4/AD7173-8/AD7175-2
  *  AD7175-8/AD7176-2/AD7177-2
  *
@@ -80,6 +81,11 @@
 #define AD7175_2_ID			0x0cd0
 #define AD7172_4_ID			0x2050
 #define AD7173_ID			0x30d0
+#define AD4111_ID			AD7173_ID
+#define AD4112_ID			AD7173_ID
+#define AD4114_ID			AD7173_ID
+#define AD4116_ID			0x34d0
+#define AD4115_ID			0x38d0
 #define AD7175_8_ID			0x3cd0
 #define AD7177_ID			0x4fd0
 #define AD7173_ID_MASK			GENMASK(15, 4)
@@ -110,6 +116,7 @@
 
 #define AD7173_GPO12_DATA(x)	BIT((x) + 0)
 #define AD7173_GPO23_DATA(x)	BIT((x) + 4)
+#define AD4111_GPO01_DATA(x)	BIT((x) + 6)
 #define AD7173_GPO_DATA(x)	((x) < 2 ? AD7173_GPO12_DATA(x) : AD7173_GPO23_DATA(x))
 
 #define AD7173_INTERFACE_DATA_STAT	BIT(6)
@@ -128,6 +135,16 @@
 #define AD7173_VOLTAGE_INT_REF_uV	2500000
 #define AD7173_TEMP_SENSIIVITY_uV_per_C	477
 #define AD7177_ODR_START_VALUE		0x07
+#define AD4111_SHUNT_RESISTOR_OHM	50
+#define AD4111_DIVIDER_RATIO		10
+#define AD4111_CURRENT_CHAN_CUTOFF	16
+#define AD4111_VINCOM_INPUT		0x10
+
+/* pin <  num_voltage_in is a normal voltage input */
+/* pin >= num_voltage_in_div is a voltage input without a divider */
+#define AD4111_IS_VINCOM_MISMATCH(pin1, pin2) ((pin1) == AD4111_VINCOM_INPUT && \
+					       (pin2) < st->info->num_voltage_in && \
+					       (pin2) >= st->info->num_voltage_in_div)
 
 #define AD7173_FILTER_ODR0_MASK		GENMASK(5, 0)
 #define AD7173_MAX_CONFIGS		8
@@ -136,18 +153,27 @@ struct ad7173_device_info {
 	const unsigned int *sinc5_data_rates;
 	unsigned int num_sinc5_data_rates;
 	unsigned int odr_start_value;
+	/*
+	 * AD4116 has both inputs with a voltage divider and without.
+	 * These inputs cannot be mixed in the channel configuration.
+	 * Does not include the VINCOM input.
+	 */
+	unsigned int num_voltage_in_div;
 	unsigned int num_channels;
 	unsigned int num_configs;
-	unsigned int num_inputs;
+	unsigned int num_voltage_in;
 	unsigned int clock;
 	unsigned int id;
 	char *name;
+	bool has_current_inputs;
+	bool has_vincom_input;
 	bool has_temp;
 	/* ((AVDD1 − AVSS)/5) */
 	bool has_pow_supply_monitoring;
 	bool has_input_buf;
 	bool has_int_ref;
 	bool has_ref2;
+	bool higher_gpio_bits;
 	u8 num_gpios;
 };
 
@@ -189,6 +215,24 @@ struct ad7173_state {
 #endif
 };
 
+static unsigned int ad4115_sinc5_data_rates[] = {
+	24845000, 24845000, 20725000, 20725000,	/*  0-3  */
+	15564000, 13841000, 10390000, 10390000,	/*  4-7  */
+	4994000,  2499000,  1000000,  500000,	/*  8-11 */
+	395500,   200000,   100000,   59890,	/* 12-15 */
+	49920,    20000,    16660,    10000,	/* 16-19 */
+	5000,	  2500,     2500,		/* 20-22 */
+};
+
+static unsigned int ad4116_sinc5_data_rates[] = {
+	12422360, 12422360, 12422360, 12422360,	/*  0-3  */
+	10362690, 10362690, 7782100,  6290530,	/*  4-7  */
+	5194800,  2496900,  1007600,  499900,	/*  8-11 */
+	390600,	  200300,   100000,   59750,	/* 12-15 */
+	49840,	  20000,    16650,    10000,	/* 16-19 */
+	5000,	  2500,	    1250,		/* 20-22 */
+};
+
 static const unsigned int ad7173_sinc5_data_rates[] = {
 	6211000, 6211000, 6211000, 6211000, 6211000, 6211000, 5181000, 4444000,	/*  0-7  */
 	3115000, 2597000, 1007000, 503800,  381000,  200300,  100500,  59520,	/*  8-15 */
@@ -204,13 +248,114 @@ static const unsigned int ad7175_sinc5_data_rates[] = {
 	5000,					/* 20    */
 };
 
+static unsigned int ad4111_current_channel_config[] = {
+	/* Ain sel: pos        neg    */
+	0x1E8, /* 15:IIN0+    8:IIN0− */
+	0x1C9, /* 14:IIN1+    9:IIN1− */
+	0x1AA, /* 13:IIN2+   10:IIN2− */
+	0x18B, /* 12:IIN3+   11:IIN3− */
+};
+
+static const struct ad7173_device_info ad4111_device_info = {
+	.name = "ad4111",
+	.id = AD4111_ID,
+	.num_voltage_in_div = 8,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 8,
+	.num_gpios = 2,
+	.higher_gpio_bits = true,
+	.has_temp = true,
+	.has_vincom_input = true,
+	.has_input_buf = true,
+	.has_current_inputs = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4112_device_info = {
+	.name = "ad4112",
+	.id = AD4112_ID,
+	.num_voltage_in_div = 8,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 8,
+	.num_gpios = 2,
+	.higher_gpio_bits = true,
+	.has_vincom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_current_inputs = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4114_device_info = {
+	.name = "ad4114",
+	.id = AD4114_ID,
+	.num_voltage_in_div = 16,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vincom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4115_device_info = {
+	.name = "ad4115",
+	.id = AD4115_ID,
+	.num_voltage_in_div = 16,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vincom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 8 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad4115_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad4115_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4116_device_info = {
+	.name = "ad4116",
+	.id = AD4116_ID,
+	.num_voltage_in_div = 11,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vincom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 4 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad4116_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad4116_sinc5_data_rates),
+};
+
 static const struct ad7173_device_info ad7172_2_device_info = {
 	.name = "ad7172-2",
 	.id = AD7172_2_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -223,10 +368,11 @@ static const struct ad7173_device_info ad7172_2_device_info = {
 static const struct ad7173_device_info ad7172_4_device_info = {
 	.name = "ad7172-4",
 	.id = AD7172_4_ID,
-	.num_inputs = 9,
+	.num_voltage_in = 9,
 	.num_channels = 8,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = false,
 	.has_input_buf = true,
 	.has_ref2 = true,
@@ -239,10 +385,11 @@ static const struct ad7173_device_info ad7172_4_device_info = {
 static const struct ad7173_device_info ad7173_8_device_info = {
 	.name = "ad7173-8",
 	.id = AD7173_ID,
-	.num_inputs = 17,
+	.num_voltage_in = 17,
 	.num_channels = 16,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -256,10 +403,11 @@ static const struct ad7173_device_info ad7173_8_device_info = {
 static const struct ad7173_device_info ad7175_2_device_info = {
 	.name = "ad7175-2",
 	.id = AD7175_2_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -272,10 +420,11 @@ static const struct ad7173_device_info ad7175_2_device_info = {
 static const struct ad7173_device_info ad7175_8_device_info = {
 	.name = "ad7175-8",
 	.id = AD7175_8_ID,
-	.num_inputs = 17,
+	.num_voltage_in = 17,
 	.num_channels = 16,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -289,10 +438,11 @@ static const struct ad7173_device_info ad7175_8_device_info = {
 static const struct ad7173_device_info ad7176_2_device_info = {
 	.name = "ad7176-2",
 	.id = AD7176_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = false,
 	.has_input_buf = false,
 	.has_int_ref = true,
@@ -305,10 +455,11 @@ static const struct ad7173_device_info ad7176_2_device_info = {
 static const struct ad7173_device_info ad7177_2_device_info = {
 	.name = "ad7177-2",
 	.id = AD7177_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -358,6 +509,15 @@ static int ad7173_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
 	return 0;
 }
 
+static int ad4111_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
+			     unsigned int offset, unsigned int *reg,
+			     unsigned int *mask)
+{
+	*mask = AD4111_GPO01_DATA(offset);
+	*reg = base;
+	return 0;
+}
+
 static void ad7173_gpio_disable(void *data)
 {
 	struct ad7173_state *st = data;
@@ -390,7 +550,10 @@ static int ad7173_gpio_init(struct ad7173_state *st)
 	gpio_regmap.regmap = st->reg_gpiocon_regmap;
 	gpio_regmap.ngpio = st->info->num_gpios;
 	gpio_regmap.reg_set_base = AD7173_REG_GPIO;
-	gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
+	if (st->info->higher_gpio_bits)
+		gpio_regmap.reg_mask_xlate = ad4111_mask_xlate;
+	else
+		gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
 
 	st->gpio_regmap = devm_gpio_regmap_register(dev, &gpio_regmap);
 	ret = PTR_ERR_OR_ZERO(st->gpio_regmap);
@@ -690,18 +853,33 @@ static int ad7173_read_raw(struct iio_dev *indio_dev,
 
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SCALE:
-		if (chan->type == IIO_TEMP) {
+
+		switch (chan->type) {
+		case IIO_TEMP:
 			temp = AD7173_VOLTAGE_INT_REF_uV * MILLI;
 			temp /= AD7173_TEMP_SENSIIVITY_uV_per_C;
 			*val = temp;
 			*val2 = chan->scan_type.realbits;
-		} else {
+			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_VOLTAGE:
 			*val = ad7173_get_ref_voltage_milli(st, ch->cfg.ref_sel);
 			*val2 = chan->scan_type.realbits - !!(ch->cfg.bipolar);
+
+			if (chan->channel < st->info->num_voltage_in_div)
+				*val *= AD4111_DIVIDER_RATIO;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_CURRENT:
+			*val = ad7173_get_ref_voltage_milli(st, ch->cfg.ref_sel);
+			*val /= AD4111_SHUNT_RESISTOR_OHM;
+			*val2 = chan->scan_type.realbits - ch->cfg.bipolar;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		default:
+			return -EINVAL;
 		}
-		return IIO_VAL_FRACTIONAL_LOG2;
 	case IIO_CHAN_INFO_OFFSET:
-		if (chan->type == IIO_TEMP) {
+
+		switch (chan->type) {
+		case IIO_TEMP:
 			/* 0 Kelvin -> raw sample */
 			temp   = -ABSOLUTE_ZERO_MILLICELSIUS;
 			temp  *= AD7173_TEMP_SENSIIVITY_uV_per_C;
@@ -710,10 +888,14 @@ static int ad7173_read_raw(struct iio_dev *indio_dev,
 						       AD7173_VOLTAGE_INT_REF_uV *
 						       MILLI);
 			*val   = -temp;
-		} else {
+			return IIO_VAL_INT;
+		case IIO_VOLTAGE:
+		case IIO_CURRENT:
 			*val = -BIT(chan->scan_type.realbits - 1);
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
 		}
-		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		reg = st->channels[chan->address].cfg.odr;
 
@@ -935,6 +1117,23 @@ static int ad7173_register_clk_provider(struct iio_dev *indio_dev)
 					   &st->int_clk_hw);
 }
 
+static int ad4111_validate_current_ain(struct ad7173_state *st,
+				       const unsigned int ain[AD7173_NO_AINS_PER_CHANNEL])
+{
+	struct device *dev = &st->sd.spi->dev;
+
+	if (!st->info->has_current_inputs)
+		return dev_err_probe(dev, -EINVAL,
+			"Model %s does not support current channels\n",
+			st->info->name);
+
+	if (ain[0] >= ARRAY_SIZE(ad4111_current_channel_config))
+		return dev_err_probe(dev, -EINVAL,
+			"For current channels single-channel must be <[0-3]>\n");
+
+	return 0;
+}
+
 static int ad7173_validate_voltage_ain_inputs(struct ad7173_state *st,
 					      unsigned int ain0, unsigned int ain1)
 {
@@ -946,15 +1145,30 @@ static int ad7173_validate_voltage_ain_inputs(struct ad7173_state *st,
 	    st->info->has_pow_supply_monitoring)
 		return 0;
 
-	special_input0 = AD7173_IS_REF_INPUT(ain0);
-	special_input1 = AD7173_IS_REF_INPUT(ain1);
+	special_input0 = AD7173_IS_REF_INPUT(ain0) ||
+			 (ain0 == AD4111_VINCOM_INPUT && st->info->has_vincom_input);
+	special_input1 = AD7173_IS_REF_INPUT(ain1) ||
+			 (ain1 == AD4111_VINCOM_INPUT && st->info->has_vincom_input);
+
+	if (st->info->has_vincom_input)
+		if (AD4111_IS_VINCOM_MISMATCH(ain0, ain1) ||
+		    AD4111_IS_VINCOM_MISMATCH(ain1, ain0))
+			return dev_err_probe(dev, -EINVAL,
+				"VINCOM must be paired with inputs having divider.\n");
 
-	if ((ain0 >= st->info->num_inputs && !special_input0) ||
-	    (ain1 >= st->info->num_inputs && !special_input1))
+	if ((ain0 >= st->info->num_voltage_in && !special_input0) ||
+	    (ain1 >= st->info->num_voltage_in && !special_input1))
 		return dev_err_probe(dev, -EINVAL,
 				     "Input pin number out of range for pair (%d %d).\n",
 				     ain0, ain1);
 
+	if (!special_input0 && !special_input1 &&
+	    ((ain0 >= st->info->num_voltage_in_div) !=
+	     (ain1 >= st->info->num_voltage_in_div)))
+		return dev_err_probe(dev, -EINVAL,
+			"Both inputs must either have a voltage divider or not have: (%d %d).\n",
+			ain0, ain1);
+
 	return 0;
 }
 
@@ -985,7 +1199,7 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 	struct device *dev = indio_dev->dev.parent;
 	struct iio_chan_spec *chan_arr, *chan;
 	unsigned int ain[AD7173_NO_AINS_PER_CHANNEL], chan_index = 0;
-	int ref_sel, ret, num_channels;
+	int ref_sel, ret, is_current_chan, num_channels;
 
 	num_channels = device_get_child_node_count(dev);
 
@@ -1032,15 +1246,38 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 
 	device_for_each_child_node_scoped(dev, child) {
 		chan = &chan_arr[chan_index];
+		*chan = ad7173_channel_template;
 		chan_st_priv = &chans_st_arr[chan_index];
 		ret = fwnode_property_read_u32_array(child, "diff-channels",
 						     ain, ARRAY_SIZE(ain));
-		if (ret)
-			return ret;
+		if (ret) {
+			ret = fwnode_property_read_u32(child, "single-channel",
+						       ain);
+			if (ret)
+				return dev_err_probe(dev, ret,
+					"Channel must define one of diff-channels or single-channel.\n");
 
-		ret = ad7173_validate_voltage_ain_inputs(st, ain[0], ain[1]);
-		if (ret)
-			return ret;
+			is_current_chan = fwnode_property_read_bool(child, "adi,current-channel");
+		} else {
+			chan->differential = true;
+		}
+
+		if (is_current_chan) {
+			ret = ad4111_validate_current_ain(st, ain);
+			if (ret)
+				return ret;
+		} else {
+			if (!chan->differential) {
+				ret = fwnode_property_read_u32(child,
+					"common-mode-channel", ain + 1);
+				if (ret)
+					return dev_err_probe(dev, ret,
+						"common-mode-channel must be defined for single-ended channels.\n");
+			}
+			ret = ad7173_validate_voltage_ain_inputs(st, ain[0], ain[1]);
+			if (ret)
+				return ret;
+		}
 
 		ret = fwnode_property_match_property_string(child,
 							    "adi,reference-select",
@@ -1059,14 +1296,9 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 			st->adc_mode |= AD7173_ADC_MODE_REF_EN;
 		chan_st_priv->cfg.ref_sel = ref_sel;
 
-		*chan = ad7173_channel_template;
 		chan->address = chan_index;
 		chan->scan_index = chan_index;
 		chan->channel = ain[0];
-		chan->channel2 = ain[1];
-		chan->differential = true;
-
-		chan_st_priv->ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
 		chan_st_priv->chan_reg = chan_index;
 		chan_st_priv->cfg.input_buf = st->info->has_input_buf;
 		chan_st_priv->cfg.odr = 0;
@@ -1075,6 +1307,17 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 		if (chan_st_priv->cfg.bipolar)
 			chan->info_mask_separate |= BIT(IIO_CHAN_INFO_OFFSET);
 
+		if (is_current_chan) {
+			chan->type = IIO_CURRENT;
+			chan->differential = false;
+			chan->channel2 = 0;
+			chan_st_priv->ain = ad4111_current_channel_config[ain[0]];
+		} else {
+			chan_st_priv->cfg.input_buf = st->info->has_input_buf;
+			chan->channel2 = ain[1];
+			chan_st_priv->ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
+		}
+
 		chan_index++;
 	}
 	return 0;
@@ -1201,6 +1444,11 @@ static int ad7173_probe(struct spi_device *spi)
 }
 
 static const struct of_device_id ad7173_of_match[] = {
+	{ .compatible = "ad4111",	.data = &ad4111_device_info },
+	{ .compatible = "ad4112",	.data = &ad4112_device_info },
+	{ .compatible = "ad4114",	.data = &ad4114_device_info },
+	{ .compatible = "ad4115",	.data = &ad4115_device_info },
+	{ .compatible = "ad4116",	.data = &ad4116_device_info },
 	{ .compatible = "adi,ad7172-2", .data = &ad7172_2_device_info },
 	{ .compatible = "adi,ad7172-4", .data = &ad7172_4_device_info },
 	{ .compatible = "adi,ad7173-8", .data = &ad7173_8_device_info },
@@ -1213,6 +1461,11 @@ static const struct of_device_id ad7173_of_match[] = {
 MODULE_DEVICE_TABLE(of, ad7173_of_match);
 
 static const struct spi_device_id ad7173_id_table[] = {
+	{ "ad4111",   (kernel_ulong_t)&ad4111_device_info },
+	{ "ad4112",   (kernel_ulong_t)&ad4112_device_info },
+	{ "ad4114",   (kernel_ulong_t)&ad4114_device_info },
+	{ "ad4115",   (kernel_ulong_t)&ad4115_device_info },
+	{ "ad4116",   (kernel_ulong_t)&ad4116_device_info },
 	{ "ad7172-2", (kernel_ulong_t)&ad7172_2_device_info },
 	{ "ad7172-4", (kernel_ulong_t)&ad7172_4_device_info },
 	{ "ad7173-8", (kernel_ulong_t)&ad7173_8_device_info },
@@ -1237,5 +1490,5 @@ module_spi_driver(ad7173_driver);
 MODULE_IMPORT_NS(IIO_AD_SIGMA_DELTA);
 MODULE_AUTHOR("Lars-Peter Clausen <lars@xxxxxxxxx>");
 MODULE_AUTHOR("Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>");
-MODULE_DESCRIPTION("Analog Devices AD7172/AD7173/AD7175/AD7176 ADC driver");
+MODULE_DESCRIPTION("Analog Devices AD7173 and similar ADC driver");
 MODULE_LICENSE("GPL");

-- 
2.43.0