Re: [PATCH v2 3/5] iio: adc: ad7292: use devm_regulator_get_enable_read_voltage

[Nuno Sá]

On Wed, 2024-06-12 at 16:03 -0500, David Lechner wrote:
> This makes use of the new devm_regulator_get_enable_read_voltage()
> function to reduce boilerplate code.
> 
> Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
> ---
> v2 changes:
> * avoid else in return value check
> * use macro instead of comment to document internal reference voltage
> ---
>  drivers/iio/adc/ad7292.c | 36 ++++++------------------------------
>  1 file changed, 6 insertions(+), 30 deletions(-)
> 
> diff --git a/drivers/iio/adc/ad7292.c b/drivers/iio/adc/ad7292.c
> index 6aadd14f459d..87ffe66058a1 100644
> --- a/drivers/iio/adc/ad7292.c
> +++ b/drivers/iio/adc/ad7292.c
> @@ -17,6 +17,8 @@
>  
>  #define ADI_VENDOR_ID 0x0018
>  
> +#define AD7292_INTERNAL_REF_MV 1250
> +
>  /* AD7292 registers definition */
>  #define AD7292_REG_VENDOR_ID		0x00
>  #define AD7292_REG_CONF_BANK		0x05
> @@ -79,7 +81,6 @@ static const struct iio_chan_spec ad7292_channels_diff[] = {
>  
>  struct ad7292_state {
>  	struct spi_device *spi;
> -	struct regulator *reg;
>  	unsigned short vref_mv;
>  
>  	__be16 d16 __aligned(IIO_DMA_MINALIGN);
> @@ -250,13 +251,6 @@ static const struct iio_info ad7292_info = {
>  	.read_raw = ad7292_read_raw,
>  };
>  
> -static void ad7292_regulator_disable(void *data)
> -{
> -	struct ad7292_state *st = data;
> -
> -	regulator_disable(st->reg);
> -}
> -
>  static int ad7292_probe(struct spi_device *spi)
>  {
>  	struct ad7292_state *st;
> @@ -277,29 +271,11 @@ static int ad7292_probe(struct spi_device *spi)
>  		return -EINVAL;
>  	}
>  
> -	st->reg = devm_regulator_get_optional(&spi->dev, "vref");
> -	if (!IS_ERR(st->reg)) {
> -		ret = regulator_enable(st->reg);
> -		if (ret) {
> -			dev_err(&spi->dev,
> -				"Failed to enable external vref supply\n");
> -			return ret;
> -		}
> -
> -		ret = devm_add_action_or_reset(&spi->dev,
> -					       ad7292_regulator_disable, st);
> -		if (ret)
> -			return ret;
> -
> -		ret = regulator_get_voltage(st->reg);
> -		if (ret < 0)
> -			return ret;
> +	ret = devm_regulator_get_enable_read_voltage(&spi->dev, "vref");
> +	if (ret < 0 && ret == -ENODEV)

ret != -ENODEV?

- Nuno Sá