RE: [PATCH v2 2/4] arm64: dts: exynos: add initial CMU clock nodes in Exynos Auto v920

[Alim Akhtar]

> -----Original Message-----
> From: Sunyeal Hong <sunyeal.hong@xxxxxxxxxxx>
> Sent: Monday, July 8, 2024 4:43 AM
> To: Krzysztof Kozlowski <krzk@xxxxxxxxxx>; Sylwester Nawrocki
> <s.nawrocki@xxxxxxxxxxx>; Chanwoo Choi <cw00.choi@xxxxxxxxxxx>;
> Alim Akhtar <alim.akhtar@xxxxxxxxxxx>; Michael Turquette
> <mturquette@xxxxxxxxxxxx>; Stephen Boyd <sboyd@xxxxxxxxxx>; Rob
> Herring <robh@xxxxxxxxxx>; Conor Dooley <conor+dt@xxxxxxxxxx>
> Cc: linux-samsung-soc@xxxxxxxxxxxxxxx; linux-clk@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; Sunyeal Hong <sunyeal.hong@xxxxxxxxxxx>
> Subject: [PATCH v2 2/4] arm64: dts: exynos: add initial CMU clock nodes in
> Exynos Auto v920
> 
> Add cmu_top, cmu_peric0 clock nodes and
> switch USI clocks instead of dummy fixed-rate-clock.
> 
> Signed-off-by: Sunyeal Hong <sunyeal.hong@xxxxxxxxxxx>
> ---
>  .../arm64/boot/dts/exynos/exynosautov920.dtsi | 40 +++++++++++++------
>  1 file changed, 27 insertions(+), 13 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> index c1c8566d74f5..54fc32074379 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> @@ -6,6 +6,7 @@
>   *
>   */
> 
> +#include <dt-bindings/clock/samsung,exynosautov920.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/soc/samsung,exynos-usi.h>
> 
> @@ -38,17 +39,6 @@ xtcxo: clock {
>  		clock-output-names = "oscclk";
>  	};
> 
> -	/*
> -	 * FIXME: Keep the stub clock for serial driver, until proper clock
> -	 * driver is implemented.
> -	 */
> -	clock_usi: clock-usi {
> -		compatible = "fixed-clock";
> -		#clock-cells = <0>;
> -		clock-frequency = <200000000>;
> -		clock-output-names = "usi";
> -	};
> -
>  	cpus: cpus {
>  		#address-cells = <2>;
>  		#size-cells = <0>;
> @@ -182,6 +172,28 @@ chipid@10000000 {
>  			reg = <0x10000000 0x24>;
>  		};
> 
> +		cmu_peric0: clock-controller@10800000 {
> +			compatible = "samsung,exynosautov920-cmu-
> peric0";
> +			reg = <0x10800000 0x8000>;
Please cross check the size of the register range, this looks to be more then what is needed. 

> +			#clock-cells = <1>;
> +
> +			clocks = <&xtcxo>,
> +				 <&cmu_top DOUT_CLKCMU_PERIC0_NOC>,
> +				 <&cmu_top DOUT_CLKCMU_PERIC0_IP>;
> +			clock-names = "oscclk",
> +				      "noc",
> +				      "ip";
> +		};
> +
> +		cmu_top: clock-controller@11000000 {
> +			compatible = "samsung,exynosautov920-cmu-top";
> +			reg = <0x11000000 0x8000>;
> +			#clock-cells = <1>;
> +
> +			clocks = <&xtcxo>;
> +			clock-names = "oscclk";
> +		};
> +
>  		gic: interrupt-controller@10400000 {
>  			compatible = "arm,gic-v3";
>  			#interrupt-cells = <3>;
> @@ -213,7 +225,8 @@ usi_0: usi@108800c0 {
>  			#address-cells = <1>;
>  			#size-cells = <1>;
>  			ranges;
> -			clocks = <&clock_usi>, <&clock_usi>;
> +			clocks = <&cmu_peric0
> CLK_MOUT_PERIC0_NOC_USER>,
> +				 <&cmu_peric0
> CLK_DOUT_PERIC0_USI00_USI>;
>  			clock-names = "pclk", "ipclk";
>  			status = "disabled";
> 
> @@ -224,7 +237,8 @@ serial_0: serial@10880000 {
>  				interrupts = <GIC_SPI 764
> IRQ_TYPE_LEVEL_HIGH>;
>  				pinctrl-names = "default";
>  				pinctrl-0 = <&uart0_bus>;
> -				clocks = <&clock_usi>, <&clock_usi>;
> +				clocks = <&cmu_peric0
> CLK_MOUT_PERIC0_NOC_USER>,
> +					 <&cmu_peric0
> CLK_DOUT_PERIC0_USI00_USI>;
>  				clock-names = "uart", "clk_uart_baud0";
>  				samsung,uart-fifosize = <256>;
>  				status = "disabled";
> --
> 2.45.2