[PATCH v2 2/3] clk: add driver for voltage controlled oscillators

[Heiko Stuebner]

In contrast to fixed clocks that are described as ungateable, boards
sometimes use additional oscillators for things like PCIe reference
clocks, that need actual supplies to get enabled and enable-gpios to be
toggled for them to work.

This adds a driver for those generic voltage controlled oscillators,
that can show up in schematics looking like

         ----------------
Enable - | 100MHz,3.3V, | - VDD
         |    3225      |
   GND - |              | - OUT
         ----------------

Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
---
 drivers/clk/Kconfig   |  10 ++++
 drivers/clk/Makefile  |   1 +
 drivers/clk/clk-vco.c | 133 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 144 insertions(+)
 create mode 100644 drivers/clk/clk-vco.c

diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 3e9099504fad4..e93a380b6ee47 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -414,6 +414,16 @@ config COMMON_CLK_VC7
 	  Renesas Versaclock7 is a family of configurable clock generator
 	  and jitter attenuator ICs with fractional and integer dividers.
 
+config COMMON_CLK_VCO
+	tristate "Clock driver for voltage controlled oscillators"
+	depends on GPIOLIB && REGULATOR
+	help
+	  This driver supports generic voltage controlled oscillators that
+	  are not configurable but need supplies to be enabled to run.
+	  Generally they need a supply voltage to be enabled and may also
+	  require a separate enable pin, though in a lot of cases, vdd
+	  and enable control might be tied to the same supply.
+
 config COMMON_CLK_STM32F
 	def_bool COMMON_CLK && (MACH_STM32F429 || MACH_STM32F469 || MACH_STM32F746)
 	help
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 4abe16c8ccdfe..ca7b7b7ddfd8d 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -79,6 +79,7 @@ obj-$(CONFIG_COMMON_CLK_SI521XX)	+= clk-si521xx.o
 obj-$(CONFIG_COMMON_CLK_VC3)		+= clk-versaclock3.o
 obj-$(CONFIG_COMMON_CLK_VC5)		+= clk-versaclock5.o
 obj-$(CONFIG_COMMON_CLK_VC7)		+= clk-versaclock7.o
+obj-$(CONFIG_COMMON_CLK_VCO)		+= clk-vco.o
 obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
 obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
 
diff --git a/drivers/clk/clk-vco.c b/drivers/clk/clk-vco.c
new file mode 100644
index 0000000000000..f7fe2bc627f36
--- /dev/null
+++ b/drivers/clk/clk-vco.c
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2024 Heiko Stuebner <heiko@xxxxxxxxx>
+ *
+ * Generic voltage controlled oscillator
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+struct clk_vco {
+	struct device *dev;
+	struct clk_hw hw;
+	u32 rate;
+	struct regulator *supply;
+	struct gpio_desc *enable_gpio;
+};
+
+#define to_clk_vco(_hw) container_of(_hw, struct clk_vco, hw)
+
+static int clk_vco_prepare(struct clk_hw *hw)
+{
+	return regulator_enable(to_clk_vco(hw)->supply);
+}
+
+static void clk_vco_unprepare(struct clk_hw *hw)
+{
+	regulator_disable(to_clk_vco(hw)->supply);
+}
+
+static int clk_vco_enable(struct clk_hw *hw)
+{
+	gpiod_set_value(to_clk_vco(hw)->enable_gpio, 1);
+	return 0;
+}
+
+static void clk_vco_disable(struct clk_hw *hw)
+{
+	gpiod_set_value(to_clk_vco(hw)->enable_gpio, 0);
+}
+
+static unsigned long clk_vco_recalc_rate(struct clk_hw *hw,
+					       unsigned long parent_rate)
+{
+	return to_clk_vco(hw)->rate;
+}
+
+const struct clk_ops clk_vco_ops = {
+	.prepare = clk_vco_prepare,
+	.unprepare = clk_vco_unprepare,
+	.enable = clk_vco_enable,
+	.disable = clk_vco_disable,
+	.recalc_rate = clk_vco_recalc_rate,
+};
+
+static int clk_vco_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_vco *clkgen;
+	const char *clk_name;
+	int ret;
+
+	clkgen = devm_kzalloc(dev, sizeof(*clkgen), GFP_KERNEL);
+	if (!clkgen)
+		return -ENOMEM;
+
+	clkgen->dev = dev;
+
+	if (device_property_read_u32(dev, "clock-frequency", &clkgen->rate))
+		return dev_err_probe(dev, -EIO, "failed to get clock-frequency");
+
+	ret = device_property_read_string(dev, "clock-output-names", &clk_name);
+	if (ret)
+		clk_name = fwnode_get_name(dev->fwnode);
+
+	clkgen->supply = devm_regulator_get_optional(dev, "vdd");
+	if (IS_ERR(clkgen->supply)) {
+		if (PTR_ERR(clkgen->supply) != -ENODEV)
+			return dev_err_probe(dev, PTR_ERR(clkgen->supply),
+					     "failed to get regulator\n");
+		clkgen->supply = NULL;
+	}
+
+	clkgen->enable_gpio = devm_gpiod_get_optional(dev, "enable",
+						      GPIOD_OUT_LOW);
+	if (IS_ERR(clkgen->enable_gpio))
+		return dev_err_probe(dev, PTR_ERR(clkgen->enable_gpio),
+				     "failed to get gpio\n");
+
+	ret = gpiod_direction_output(clkgen->enable_gpio, 0);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "failed to set gpio output");
+
+	clkgen->hw.init = CLK_HW_INIT_NO_PARENT(clk_name, &clk_vco_ops, 0);
+
+	/* register the clock */
+	ret = devm_clk_hw_register(dev, &clkgen->hw);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to register clock\n");
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
+					  &clkgen->hw);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to register clock provider\n");
+
+	return 0;
+}
+
+static const struct of_device_id clk_vco_ids[] = {
+	{ .compatible = "voltage-oscillator" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, clk_vco_ids);
+
+static struct platform_driver clk_vco_driver = {
+	.driver = {
+		.name = "clk_vco",
+		.of_match_table = clk_vco_ids,
+	},
+	.probe = clk_vco_probe,
+};
+module_platform_driver(clk_vco_driver);
+
+MODULE_AUTHOR("Heiko Stuebner <heiko@xxxxxxxxx>");
+MODULE_DESCRIPTION("Voltage controlled oscillator driver");
+MODULE_LICENSE("GPL");
-- 
2.39.2