Re: [PATCH v2 3/4] ata: ahci_imx: Enlarge RX water mark for i.MX8QM SATA

[Damien Le Moal]

On 7/15/24 10:53, Richard Zhu wrote:
> The RXWM(RxWaterMark) sets the minimum number of free location within
> the RX FIFO before the watermark is exceeded which in turn will cause
> the Transport Layer to instruct the Link Layer to transmit HOLDS to
> the transmitting end.
> 
> Based on the default RXWM value 0x20, RX FIFO overflow might be
> observed on i.MX8QM MEK board, when some Gen3 SATA disks are used.
> 
> The FIFO overflow will result in CRC error, internal error and protocol
> error, then the SATA link is not stable anymore.
> 
> To fix this issue, enlarge RX water mark setting from 0x20 to 0x29.
> 
> Fixes: 027fa4dee935 ("ahci: imx: add the imx8qm ahci sata support")
> Cc: stable@xxxxxxxxxxxxxxx
> Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> ---
>  drivers/ata/ahci_imx.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
> index e94c0fdea2260..12d69a6429b6a 100644
> --- a/drivers/ata/ahci_imx.c
> +++ b/drivers/ata/ahci_imx.c
> @@ -45,6 +45,10 @@ enum {
>  	/* Clock Reset Register */
>  	IMX_CLOCK_RESET				= 0x7f3f,
>  	IMX_CLOCK_RESET_RESET			= 1 << 0,
> +	/* IMX8QM SATA specific control registers */
> +	IMX8QM_SATA_AHCI_VEND_PTC		= 0xc8,
> +	IMX8QM_SATA_AHCI_VEND_PTC_RXWM_MASK	= 0x7f,

Please use GENMASK() macro to define this.

> +	IMX8QM_SATA_AHCI_VEND_PTC_NEWRXWM	= 0x29,

Here too. And I do not see the point of the "NEW" in the macro name.

Also, what is "_VEND_" supposed to mean in the macro names ? "Vendor" ?
If that is the case, remove that too, which will give you shorter macro names.
If not, then spell it out because that is not clear.

>  };
>  
>  enum ahci_imx_type {
> @@ -466,6 +470,12 @@ static int imx8_sata_enable(struct ahci_host_priv *hpriv)
>  	phy_power_off(imxpriv->cali_phy0);
>  	phy_exit(imxpriv->cali_phy0);
>  
> +	/* RxWaterMark setting */
> +	val = readl(hpriv->mmio + IMX8QM_SATA_AHCI_VEND_PTC);
> +	val &= ~IMX8QM_SATA_AHCI_VEND_PTC_RXWM_MASK;
> +	val |= IMX8QM_SATA_AHCI_VEND_PTC_NEWRXWM;
> +	writel(val, hpriv->mmio + IMX8QM_SATA_AHCI_VEND_PTC);
> +
>  	return 0;
>  
>  err_sata_phy_exit:

-- 
Damien Le Moal
Western Digital Research