Re: [PATCH net-next v4 11/12] microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY
From: Stefan Bigler
Date: Tue Jul 16 2024 - 01:36:08 EST
Hi Parthiban
I'm using v4 of the driver an switched from ipv4 to ipv6.
I recognized, that the Neighbor Discovery is not working as expected.
The reason for this is, that the Neighbor Solicitation packet is not recived.
This packet is sent with a Multicast MAC Address.
When I checked the code and compared it to the documentaton the calculation of the Address Hash is not ok.
See Chapter 6.4.6 Hash Addressing
Changing the function lan865x_hash fixed the problem
+static inline u32 getAddrBit(u8 addr[ETH_ALEN], u32 bit)
+{
+ return ((addr[bit/8]) >> (bit % 8)) & 1;
+}
+
static u32 lan865x_hash(u8 addr[ETH_ALEN])
{
- return (ether_crc(ETH_ALEN, addr) >> 26) & GENMASK(5, 0);
+ u32 hash_index = 0;
+ for (int i=0; i<6; i++)
+ {
+ u32 hash = 0;
+ for (int j=0; j<8; j++) {
+ hash ^= getAddrBit(addr, (j*6)+i);
+ }
+ hash_index |= (hash << i);
+ }
+ return hash_index;
}
also the fuction lan865x_set_specific_multicast_addr() must be fixed due to the overflow of the mask variable
static void lan865x_set_specific_multicast_addr(struct net_device *netdev)
@@ -301,15 +315,11 @@ static void lan865x_set_specific_multicast_addr(struct net_device *netdev)
netdev_for_each_mc_addr(ha, netdev) {
u32 bit_num = lan865x_hash(ha->addr);
- u32 mask = BIT(bit_num);
- /* 5th bit of the 6 bits hash value is used to determine which
- * bit to set in either a high or low hash register.
- */
- if (bit_num & BIT(5))
- hash_hi |= mask;
+ if (bit_num >= 32)
+ hash_hi |= (1 << (bit_num-32));
else
- hash_lo |= mask;
+ hash_lo |= (1 << bit_num);
}
/* Enabling specific multicast addresses */
I would be great if the fix can be included in the new version 5 of your driver.
Thanks a lot and best regards
Stefan
Am 2024-04-18T14:56:47.000+02:00 hat Parthiban Veerasooran <Parthiban.Veerasooran@xxxxxxxxxxxxx> geschrieben:
> The LAN8650/1 is designed to conform to the OPEN Alliance 10BASE-T1x
> MAC-PHY Serial Interface specification, Version 1.1. The IEEE Clause 4
> MAC integration provides the low pin count standard SPI interface to any
> microcontroller therefore providing Ethernet functionality without
> requiring MAC integration within the microcontroller. The LAN8650/1
> operates as an SPI client supporting SCLK clock rates up to a maximum of
> 25 MHz. This SPI interface supports the transfer of both data (Ethernet
> frames) and control (register access).
>
> By default, the chunk data payload is 64 bytes in size. The Ethernet
> Media Access Controller (MAC) module implements a 10 Mbps half duplex
> Ethernet MAC, compatible with the IEEE 802.3 standard. 10BASE-T1S
> physical layer transceiver integrated is into the LAN8650/1. The PHY and
> MAC are connected via an internal Media Independent Interface (MII).
>
> Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@xxxxxxxxxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/net/ethernet/microchip/Kconfig | 1 +
> drivers/net/ethernet/microchip/Makefile | 1 +
> .../net/ethernet/microchip/lan865x/Kconfig | 19 +
> .../net/ethernet/microchip/lan865x/Makefile | 6 +
> .../net/ethernet/microchip/lan865x/lan865x.c | 384 ++++++++++++++++++
> 6 files changed, 417 insertions(+)
> create mode 100644 drivers/net/ethernet/microchip/lan865x/Kconfig
> create mode 100644 drivers/net/ethernet/microchip/lan865x/Makefile
> create mode 100644 drivers/net/ethernet/microchip/lan865x/lan865x.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 603528948f61..f41b7f2257d2 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14374,6 +14374,12 @@ L: netdev@xxxxxxxxxxxxxxx
> S: Maintained
> F: drivers/net/ethernet/microchip/lan743x_*
>
> +MICROCHIP LAN8650/1 10BASE-T1S MACPHY ETHERNET DRIVER
> +M: Parthiban Veerasooran <parthiban.veerasooran@xxxxxxxxxxxxx>
> +L: netdev@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: drivers/net/ethernet/microchip/lan865x/lan865x.c
> +
> MICROCHIP LAN87xx/LAN937x T1 PHY DRIVER
> M: Arun Ramadoss <arun.ramadoss@xxxxxxxxxxxxx>
> R: UNGLinuxDriver@xxxxxxxxxxxxx
> diff --git a/drivers/net/ethernet/microchip/Kconfig b/drivers/net/ethernet/microchip/Kconfig
> index 43ba71e82260..06ca79669053 100644
> --- a/drivers/net/ethernet/microchip/Kconfig
> +++ b/drivers/net/ethernet/microchip/Kconfig
> @@ -56,6 +56,7 @@ config LAN743X
> To compile this driver as a module, choose M here. The module will be
> called lan743x.
>
> +source "drivers/net/ethernet/microchip/lan865x/Kconfig"
> source "drivers/net/ethernet/microchip/lan966x/Kconfig"
> source "drivers/net/ethernet/microchip/sparx5/Kconfig"
> source "drivers/net/ethernet/microchip/vcap/Kconfig"
> diff --git a/drivers/net/ethernet/microchip/Makefile b/drivers/net/ethernet/microchip/Makefile
> index bbd349264e6f..15dfbb321057 100644
> --- a/drivers/net/ethernet/microchip/Makefile
> +++ b/drivers/net/ethernet/microchip/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_LAN743X) += lan743x.o
>
> lan743x-objs := lan743x_main.o lan743x_ethtool.o lan743x_ptp.o
>
> +obj-$(CONFIG_LAN865X) += lan865x/
> obj-$(CONFIG_LAN966X_SWITCH) += lan966x/
> obj-$(CONFIG_SPARX5_SWITCH) += sparx5/
> obj-$(CONFIG_VCAP) += vcap/
> diff --git a/drivers/net/ethernet/microchip/lan865x/Kconfig b/drivers/net/ethernet/microchip/lan865x/Kconfig
> new file mode 100644
> index 000000000000..f3d60d14e202
> --- /dev/null
> +++ b/drivers/net/ethernet/microchip/lan865x/Kconfig
> @@ -0,0 +1,19 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +#
> +# Microchip LAN865x Driver Support
> +#
> +
> +if NET_VENDOR_MICROCHIP
> +
> +config LAN865X
> + tristate "LAN865x support"
> + depends on SPI
> + depends on OA_TC6
> + help
> + Support for the Microchip LAN8650/1 Rev.B1 MACPHY Ethernet chip. It
> + uses OPEN Alliance 10BASE-T1x Serial Interface specification.
> +
> + To compile this driver as a module, choose M here. The module will be
> + called lan865x.
> +
> +endif # NET_VENDOR_MICROCHIP
> diff --git a/drivers/net/ethernet/microchip/lan865x/Makefile b/drivers/net/ethernet/microchip/lan865x/Makefile
> new file mode 100644
> index 000000000000..9f5dd89c1eb8
> --- /dev/null
> +++ b/drivers/net/ethernet/microchip/lan865x/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +#
> +# Makefile for the Microchip LAN865x Driver
> +#
> +
> +obj-$(CONFIG_LAN865X) += lan865x.o
> diff --git a/drivers/net/ethernet/microchip/lan865x/lan865x.c b/drivers/net/ethernet/microchip/lan865x/lan865x.c
> new file mode 100644
> index 000000000000..9abefa8b9d9f
> --- /dev/null
> +++ b/drivers/net/ethernet/microchip/lan865x/lan865x.c
> @@ -0,0 +1,384 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Microchip's LAN865x 10BASE-T1S MAC-PHY driver
> + *
> + * Author: Parthiban Veerasooran <parthiban.veerasooran@xxxxxxxxxxxxx>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/phy.h>
> +#include <linux/oa_tc6.h>
> +
> +#define DRV_NAME "lan865x"
> +
> +/* MAC Network Control Register */
> +#define LAN865X_REG_MAC_NET_CTL 0x00010000
> +#define MAC_NET_CTL_TXEN BIT(3) /* Transmit Enable */
> +#define MAC_NET_CTL_RXEN BIT(2) /* Receive Enable */
> +
> +#define LAN865X_REG_MAC_NET_CFG 0x00010001 /* MAC Network Configuration Reg */
> +#define MAC_NET_CFG_PROMISCUOUS_MODE BIT(4)
> +#define MAC_NET_CFG_MULTICAST_MODE BIT(6)
> +#define MAC_NET_CFG_UNICAST_MODE BIT(7)
> +
> +#define LAN865X_REG_MAC_L_HASH 0x00010020 /* MAC Hash Register Bottom */
> +#define LAN865X_REG_MAC_H_HASH 0x00010021 /* MAC Hash Register Top */
> +#define LAN865X_REG_MAC_L_SADDR1 0x00010022 /* MAC Specific Addr 1 Bottom Reg */
> +#define LAN865X_REG_MAC_H_SADDR1 0x00010023 /* MAC Specific Addr 1 Top Reg */
> +
> +/* OPEN Alliance Configuration Register #0 */
> +#define OA_TC6_REG_CONFIG0 0x0004
> +#define CONFIG0_ZARFE_ENABLE BIT(12)
> +
> +struct lan865x_priv {
> + struct work_struct multicast_work;
> + struct net_device *netdev;
> + struct spi_device *spi;
> + struct oa_tc6 *tc6;
> +};
> +
> +static int lan865x_set_hw_macaddr_low_bytes(struct oa_tc6 *tc6, const u8 *mac)
> +{
> + u32 regval;
> +
> + regval = (mac[3] << 24) | (mac[2] << 16) | (mac[1] << 8) | mac[0];
> +
> + return oa_tc6_write_register(tc6, LAN865X_REG_MAC_L_SADDR1, regval);
> +}
> +
> +static int lan865x_set_hw_macaddr(struct lan865x_priv *priv, const u8 *mac)
> +{
> + int restore_ret;
> + u32 regval;
> + int ret;
> +
> + /* Configure MAC address low bytes */
> + ret = lan865x_set_hw_macaddr_low_bytes(priv->tc6, mac);
> + if (ret)
> + return ret;
> +
> + /* Prepare and configure MAC address high bytes */
> + regval = (mac[5] << 8) | mac[4];
> + ret = oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_H_SADDR1, regval);
> + if (!ret)
> + return 0;
> +
> + /* Restore the old MAC address low bytes from netdev if the new MAC
> + * address high bytes setting failed.
> + */
> + restore_ret = lan865x_set_hw_macaddr_low_bytes(priv->tc6,
> + priv->netdev->dev_addr);
> + if (restore_ret)
> + return restore_ret;
> +
> + return ret;
> +}
> +
> +static void
> +lan865x_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *info)
> +{
> + strscpy(info->driver, DRV_NAME, sizeof(info->driver));
> + strscpy(info->bus_info, dev_name(netdev->dev.parent),
> + sizeof(info->bus_info));
> +}
> +
> +static const struct ethtool_ops lan865x_ethtool_ops = {
> + .get_drvinfo = lan865x_get_drvinfo,
> + .get_link_ksettings = phy_ethtool_get_link_ksettings,
> + .set_link_ksettings = phy_ethtool_set_link_ksettings,
> +};
> +
> +static int lan865x_set_mac_address(struct net_device *netdev, void *addr)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> + struct sockaddr *address = addr;
> + int ret;
> +
> + ret = eth_prepare_mac_addr_change(netdev, addr);
> + if (ret < 0)
> + return ret;
> +
> + if (ether_addr_equal(address->sa_data, netdev->dev_addr))
> + return 0;
> +
> + ret = lan865x_set_hw_macaddr(priv, address->sa_data);
> + if (ret)
> + return ret;
> +
> + eth_hw_addr_set(netdev, address->sa_data);
> +
> + return 0;
> +}
> +
> +static u32 lan865x_hash(u8 addr[ETH_ALEN])
> +{
> + return (ether_crc(ETH_ALEN, addr) >> 26) & GENMASK(5, 0);
> +}
> +
> +static void lan865x_set_specific_multicast_addr(struct net_device *netdev)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> + struct netdev_hw_addr *ha;
> + u32 hash_lo = 0;
> + u32 hash_hi = 0;
> +
> + netdev_for_each_mc_addr(ha, netdev) {
> + u32 bit_num = lan865x_hash(ha->addr);
> + u32 mask = BIT(bit_num);
> +
> + /* 5th bit of the 6 bits hash value is used to determine which
> + * bit to set in either a high or low hash register.
> + */
> + if (bit_num & BIT(5))
> + hash_hi |= mask;
> + else
> + hash_lo |= mask;
> + }
> +
> + /* Enabling specific multicast addresses */
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_H_HASH, hash_hi)) {
> + netdev_err(netdev, "Failed to write reg_hashh");
> + return;
> + }
> +
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_L_HASH, hash_lo))
> + netdev_err(netdev, "Failed to write reg_hashl");
> +}
> +
> +static void lan865x_multicast_work_handler(struct work_struct *work)
> +{
> + struct lan865x_priv *priv = container_of(work, struct lan865x_priv,
> + multicast_work);
> + u32 regval = 0;
> +
> + if (priv->netdev->flags & IFF_PROMISC) {
> + /* Enabling promiscuous mode */
> + regval |= MAC_NET_CFG_PROMISCUOUS_MODE;
> + regval &= (~MAC_NET_CFG_MULTICAST_MODE);
> + regval &= (~MAC_NET_CFG_UNICAST_MODE);
> + } else if (priv->netdev->flags & IFF_ALLMULTI) {
> + /* Enabling all multicast mode */
> + regval &= (~MAC_NET_CFG_PROMISCUOUS_MODE);
> + regval |= MAC_NET_CFG_MULTICAST_MODE;
> + regval &= (~MAC_NET_CFG_UNICAST_MODE);
> + } else if (!netdev_mc_empty(priv->netdev)) {
> + lan865x_set_specific_multicast_addr(priv->netdev);
> + regval &= (~MAC_NET_CFG_PROMISCUOUS_MODE);
> + regval &= (~MAC_NET_CFG_MULTICAST_MODE);
> + regval |= MAC_NET_CFG_UNICAST_MODE;
> + } else {
> + /* enabling local mac address only */
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_H_HASH, 0)) {
> + netdev_err(priv->netdev, "Failed to write reg_hashh");
> + return;
> + }
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_L_HASH, 0)) {
> + netdev_err(priv->netdev, "Failed to write reg_hashl");
> + return;
> + }
> + }
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_NET_CFG, regval))
> + netdev_err(priv->netdev,
> + "Failed to enable promiscuous/multicast/normal mode");
> +}
> +
> +static void lan865x_set_multicast_list(struct net_device *netdev)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> +
> + schedule_work(&priv->multicast_work);
> +}
> +
> +static netdev_tx_t lan865x_send_packet(struct sk_buff *skb,
> + struct net_device *netdev)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> +
> + return oa_tc6_start_xmit(priv->tc6, skb);
> +}
> +
> +static int lan865x_hw_disable(struct lan865x_priv *priv)
> +{
> + u32 regval;
> +
> + if (oa_tc6_read_register(priv->tc6, LAN865X_REG_MAC_NET_CTL, ®val))
> + return -ENODEV;
> +
> + regval &= ~(MAC_NET_CTL_TXEN | MAC_NET_CTL_RXEN);
> +
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_NET_CTL, regval))
> + return -ENODEV;
> +
> + return 0;
> +}
> +
> +static int lan865x_net_close(struct net_device *netdev)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> + int ret;
> +
> + netif_stop_queue(netdev);
> + phy_stop(netdev->phydev);
> + ret = lan865x_hw_disable(priv);
> + if (ret) {
> + netdev_err(netdev, "Failed to disable the hardware: %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lan865x_hw_enable(struct lan865x_priv *priv)
> +{
> + u32 regval;
> +
> + if (oa_tc6_read_register(priv->tc6, LAN865X_REG_MAC_NET_CTL, ®val))
> + return -ENODEV;
> +
> + regval |= MAC_NET_CTL_TXEN | MAC_NET_CTL_RXEN;
> +
> + if (oa_tc6_write_register(priv->tc6, LAN865X_REG_MAC_NET_CTL, regval))
> + return -ENODEV;
> +
> + return 0;
> +}
> +
> +static int lan865x_net_open(struct net_device *netdev)
> +{
> + struct lan865x_priv *priv = netdev_priv(netdev);
> + int ret;
> +
> + ret = lan865x_hw_enable(priv);
> + if (ret) {
> + netdev_err(netdev, "Failed to enable hardware: %d\n", ret);
> + return ret;
> + }
> +
> + phy_start(netdev->phydev);
> +
> + return 0;
> +}
> +
> +static const struct net_device_ops lan865x_netdev_ops = {
> + .ndo_open = lan865x_net_open,
> + .ndo_stop = lan865x_net_close,
> + .ndo_start_xmit = lan865x_send_packet,
> + .ndo_set_rx_mode = lan865x_set_multicast_list,
> + .ndo_set_mac_address = lan865x_set_mac_address,
> +};
> +
> +static int lan865x_set_zarfe(struct lan865x_priv *priv)
> +{
> + u32 regval;
> + int ret;
> +
> + ret = oa_tc6_read_register(priv->tc6, OA_TC6_REG_CONFIG0, ®val);
> + if (ret)
> + return ret;
> +
> + /* Set Zero-Align Receive Frame Enable */
> + regval |= CONFIG0_ZARFE_ENABLE;
> +
> + return oa_tc6_write_register(priv->tc6, OA_TC6_REG_CONFIG0, regval);
> +}
> +
> +static int lan865x_probe(struct spi_device *spi)
> +{
> + struct net_device *netdev;
> + struct lan865x_priv *priv;
> + int ret;
> +
> + netdev = alloc_etherdev(sizeof(struct lan865x_priv));
> + if (!netdev)
> + return -ENOMEM;
> +
> + priv = netdev_priv(netdev);
> + priv->netdev = netdev;
> + priv->spi = spi;
> + spi_set_drvdata(spi, priv);
> + INIT_WORK(&priv->multicast_work, lan865x_multicast_work_handler);
> +
> + priv->tc6 = oa_tc6_init(spi, netdev);
> + if (!priv->tc6) {
> + ret = -ENODEV;
> + goto free_netdev;
> + }
> +
> + /* As per the point s3 in the below errata, SPI receive Ethernet frame
> + * transfer may halt when starting the next frame in the same data block
> + * (chunk) as the end of a previous frame. The RFA field should be
> + * configured to 01b or 10b for proper operation. In these modes, only
> + * one receive Ethernet frame will be placed in a single data block.
> + * When the RFA field is written to 01b, received frames will be forced
> + * to only start in the first word of the data block payload (SWO=0). As
> + * recommended, ZARFE bit in the OPEN Alliance CONFIG0 register is set
> + * to 1 for proper operation.
> + *
> + * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/Errata/LAN8650-1-Errata-80001075.pdf
> + */
> + ret = lan865x_set_zarfe(priv);
> + if (ret) {
> + dev_err(&spi->dev, "Failed to set ZARFE: %d\n", ret);
> + goto oa_tc6_exit;
> + }
> +
> + /* Get the MAC address from the SPI device tree node */
> + if (device_get_ethdev_address(&spi->dev, netdev))
> + eth_hw_addr_random(netdev);
> +
> + ret = lan865x_set_hw_macaddr(priv, netdev->dev_addr);
> + if (ret) {
> + dev_err(&spi->dev, "Failed to configure MAC: %d\n", ret);
> + goto oa_tc6_exit;
> + }
> +
> + netdev->if_port = IF_PORT_10BASET;
> + netdev->irq = spi->irq;
> + netdev->netdev_ops = &lan865x_netdev_ops;
> + netdev->ethtool_ops = &lan865x_ethtool_ops;
> +
> + ret = register_netdev(netdev);
> + if (ret) {
> + dev_err(&spi->dev, "Register netdev failed (ret = %d)", ret);
> + goto oa_tc6_exit;
> + }
> +
> + return 0;
> +
> +oa_tc6_exit:
> + oa_tc6_exit(priv->tc6);
> +free_netdev:
> + free_netdev(priv->netdev);
> + return ret;
> +}
> +
> +static void lan865x_remove(struct spi_device *spi)
> +{
> + struct lan865x_priv *priv = spi_get_drvdata(spi);
> +
> + cancel_work_sync(&priv->multicast_work);
> + unregister_netdev(priv->netdev);
> + oa_tc6_exit(priv->tc6);
> + free_netdev(priv->netdev);
> +}
> +
> +static const struct of_device_id lan865x_dt_ids[] = {
> + { .compatible = "microchip,lan8651", "microchip,lan8650" },
> + { /* Sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, lan865x_dt_ids);
> +
> +static struct spi_driver lan865x_driver = {
> + .driver = {
> + .name = DRV_NAME,
> + .of_match_table = lan865x_dt_ids,
> + },
> + .probe = lan865x_probe,
> + .remove = lan865x_remove,
> +};
> +module_spi_driver(lan865x_driver);
> +
> +MODULE_DESCRIPTION(DRV_NAME " 10Base-T1S MACPHY Ethernet Driver");
> +MODULE_AUTHOR("Parthiban Veerasooran <parthiban.veerasooran@xxxxxxxxxxxxx>");
> +MODULE_LICENSE("GPL");
> --
> 2.34.1