Re: [PATCH] riscv: dts: sophgo: Add i2c device support for sg2042

[Chen Wang]

On 2024/7/26 9:07, Inochi Amaoto wrote:
> The i2c ip of sg2042 is a standard Synopsys i2c ip, which is already
> supported by the mainline kernel.
>
> Add i2c device node for sg2042.
>
> Signed-off-by: Inochi Amaoto <inochiama@xxxxxxxxxxx>
> ---
>   arch/riscv/boot/dts/sophgo/sg2042.dtsi | 54 +++++++++++++++++++++++++-
>   1 file changed, 53 insertions(+), 1 deletion(-)
>
> diff --git a/arch/riscv/boot/dts/sophgo/sg2042.dtsi b/arch/riscv/boot/dts/sophgo/sg2042.dtsi
> index 34c802bd3f9b..eebd6817520e 100644
> --- a/arch/riscv/boot/dts/sophgo/sg2042.dtsi
> +++ b/arch/riscv/boot/dts/sophgo/sg2042.dtsi
> @@ -44,8 +44,61 @@ soc: soc {
>   		compatible = "simple-bus";
>   		#address-cells = <2>;
>   		#size-cells = <2>;
> +		interrupt-parent = <&intc>;

I would suggest this change (use common interrupt-parent for soc) in 
another separated patch and this would looks more clear.

Then this patch is only for i2c related changes.

>   		ranges;
>
> +		i2c0: i2c@7030005000 {
> +			compatible = "snps,designware-i2c";
> +			reg = <0x70 0x30005000 0x0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clocks = <&clkgen GATE_CLK_APB_I2C>;
> +			clock-names = "ref";
> +			clock-frequency = <100000>;
> +			interrupts = <101 IRQ_TYPE_LEVEL_HIGH>;
> +			resets = <&rstgen RST_I2C0>;
> +			status = "disabled";
> +		};
> +
> +		i2c1: i2c@7030006000 {
> +			compatible = "snps,designware-i2c";
> +			reg = <0x70 0x30006000 0x0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clocks = <&clkgen GATE_CLK_APB_I2C>;
> +			clock-names = "ref";
> +			clock-frequency = <100000>;
> +			interrupts = <102 IRQ_TYPE_LEVEL_HIGH>;
> +			resets = <&rstgen RST_I2C1>;
> +			status = "disabled";
> +		};
> +
> +		i2c2: i2c@7030007000 {
> +			compatible = "snps,designware-i2c";
> +			reg = <0x70 0x30007000 0x0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clocks = <&clkgen GATE_CLK_APB_I2C>;
> +			clock-names = "ref";
> +			clock-frequency = <100000>;
> +			interrupts = <103 IRQ_TYPE_LEVEL_HIGH>;
> +			resets = <&rstgen RST_I2C2>;
> +			status = "disabled";
> +		};
> +
> +		i2c3: i2c@7030008000 {
> +			compatible = "snps,designware-i2c";
> +			reg = <0x70 0x30008000 0x0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clocks = <&clkgen GATE_CLK_APB_I2C>;
> +			clock-names = "ref";
> +			clock-frequency = <100000>;
> +			interrupts = <104 IRQ_TYPE_LEVEL_HIGH>;
> +			resets = <&rstgen RST_I2C3>;
> +			status = "disabled";
> +		};
> +
>   		pllclk: clock-controller@70300100c0 {
>   			compatible = "sophgo,sg2042-pll";
>   			reg = <0x70 0x300100c0 0x0 0x40>;
> @@ -388,7 +441,6 @@ rstgen: reset-controller@7030013000 {
>   		uart0: serial@7040000000 {
>   			compatible = "snps,dw-apb-uart";
>   			reg = <0x00000070 0x40000000 0x00000000 0x00001000>;
> -			interrupt-parent = <&intc>;
I would prefer this change in a separated patch which has been mentioned 
upon.
>   			interrupts = <112 IRQ_TYPE_LEVEL_HIGH>;
>   			clock-frequency = <500000000>;
>   			clocks = <&clkgen GATE_CLK_UART_500M>,
> --
> 2.45.2