Re: [PATCH v3 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes

[Kumar, Udit]

On 7/30/2024 3:23 PM, Manorit Chawdhry wrote:
> Removes bootph-* properties from parent nodes and aligns the bootph-* to
> other u-boot.dtsi
>
> Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
> ---
>   arch/arm64/boot/dts/ti/k3-j784s4-evm.dts         | 9 +--------
>   arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 8 ++++----
>   2 files changed, 5 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index ffa38f41679d..311844490027 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -461,7 +461,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
>   };
>   

main_pmx0 has bootph-all in parent node, please consider to clean that 
as well


>   &wkup_pmx2 {
> -	bootph-all;
>   	wkup_uart0_pins_default: wkup-uart0-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -577,7 +576,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
>   };
>   
>   &wkup_pmx0 {
> -	bootph-all;
>   	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -597,7 +595,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
>   };
>   
>   &wkup_pmx1 {
> -	bootph-all;
>   	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -668,6 +665,7 @@ bucka12: buck12 {
>   				regulator-max-microvolt = <1100000>;
>   				regulator-boot-on;
>   				regulator-always-on;
> +				bootph-pre-ram;
>   			};
>   
>   			bucka3: buck3 {
> @@ -769,18 +767,15 @@ &ufs_wrapper {
>   };
>   
>   &fss {
> -	bootph-all;
>   	status = "okay";
>   };
>   
>   &ospi0 {
> -	bootph-all;
>   	status = "okay";
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
>   
>   	flash@0 {
> -		bootph-all;
>   		compatible = "jedec,spi-nor";
>   		reg = <0x0>;
>   		spi-tx-bus-width = <8>;
> @@ -837,13 +832,11 @@ partition@3fc0000 {
>   };
>   
>   &ospi1 {
> -	bootph-all;
>   	status = "okay";
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
>   
>   	flash@0 {
> -		bootph-all;
>   		compatible = "jedec,spi-nor";
>   		reg = <0x0>;
>   		spi-tx-bus-width = <1>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> index f3a6ed1c979d..3f89277e3c2c 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> @@ -7,7 +7,6 @@
>   
>   &cbass_mcu_wakeup {
>   	sms: system-controller@44083000 {
> -		bootph-all;
>   		compatible = "ti,k2g-sci";
>   		ti,host-id = <12>;
>   
> @@ -39,7 +38,6 @@ k3_reset: reset-controller {
>   	};
>   
>   	wkup_conf: bus@43000000 {
> -		bootph-all;
>   		compatible = "simple-bus";
>   		#address-cells = <1>;
>   		#size-cells = <1>;
> @@ -65,6 +63,7 @@ secure_proxy_sa3: mailbox@43600000 {
>   		 * firmware on non-MPU processors
>   		 */
>   		status = "disabled";
> +		bootph-pre-ram;
>   	};
>   
>   	mcu_ram: sram@41c00000 {
> @@ -175,10 +174,10 @@ mcu_timer0: timer@40400000 {
>   		ti,timer-pwm;
>   		/* Non-MPU Firmware usage */
>   		status = "reserved";
> +		bootph-all;

both nodes mcu_timer0 and mcu_timer1 as marked as

/* Non-MPU Firmware usage */, Please provide some message added bootph in first and removed from second

>   	};
>   
>   	mcu_timer1: timer@40410000 {
> -		bootph-all;
>   		compatible = "ti,am654-timer";
>   		reg = <0x00 0x40410000 0x00 0x400>;
>   		interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
> @@ -458,7 +457,6 @@ mcu_spi2: spi@40320000 {
>   	};
> [..]