Re: [PATCH v2 1/2] dmaengine: dw-edma: Fix unmasking STOP and ABORT interrupts for HDMA

[Mrinmay Sarkar]

On 8/7/2024 4:26 AM, Serge Semin wrote:
> On Mon, Aug 05, 2024 at 07:30:14PM +0530, Mrinmay Sarkar wrote:
> > On 8/2/2024 5:12 AM, Serge Semin wrote:
> > > On Tue, Jul 23, 2024 at 06:49:31PM +0530, Mrinmay Sarkar wrote:
> > > > The current logic is enabling both STOP_INT_MASK and ABORT_INT_MASK
> > > > bit. This is apparently masking those particular interrupts rather than
> > > > unmasking the same. If the interrupts are masked, they would never get
> > > > triggered.
> > > >
> > > > So fix the issue by unmasking the STOP and ABORT interrupts properly.
> > > >
> > > > Fixes: e74c39573d35 ("dmaengine: dw-edma: Add support for native HDMA")
> > > > cc: stable@xxxxxxxxxxxxxxx
> > > > Signed-off-by: Mrinmay Sarkar <quic_msarkar@xxxxxxxxxxx>
> > > > ---
> > > >    drivers/dma/dw-edma/dw-hdma-v0-core.c | 9 +++++----
> > > >    1 file changed, 5 insertions(+), 4 deletions(-)
> > > >
> > > > diff --git a/drivers/dma/dw-edma/dw-hdma-v0-core.c b/drivers/dma/dw-edma/dw-hdma-v0-core.c
> > > > index 10e8f07..fa89b3a 100644
> > > > --- a/drivers/dma/dw-edma/dw-hdma-v0-core.c
> > > > +++ b/drivers/dma/dw-edma/dw-hdma-v0-core.c
> > > > @@ -247,10 +247,11 @@ static void dw_hdma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
> > > >    	if (first) {
> > > >    		/* Enable engine */
> > > >    		SET_CH_32(dw, chan->dir, chan->id, ch_en, BIT(0));
> > > > -		/* Interrupt enable&unmask - done, abort */
> > > > -		tmp = GET_CH_32(dw, chan->dir, chan->id, int_setup) |
> > > > -		      HDMA_V0_STOP_INT_MASK | HDMA_V0_ABORT_INT_MASK |
> > > > -		      HDMA_V0_LOCAL_STOP_INT_EN | HDMA_V0_LOCAL_ABORT_INT_EN;
> > > Just curious, if all the interrupts were actually masked, how has this
> > > been even working?.. In other words if it affected both local and
> > > remote interrupts, then the HDMA driver has never actually worked,
> > > right?
> > Agreed, it should not work as interrupts were masked.
> >
> > But as we are enabling LIE/RIE bits (LWIE/RWIE) that eventually enabling
> > watermark
> > interrupt in HDMA case and somehow on device I could see interrupt was
> > generating with watermark and stop bit set and it was working.
> > Since we were not clearing watermark interrupt, it was also causing storm of
> > interrupt.
> Is it possible that the HDMA_V0_STOP_INT_MASK and
> HDMA_V0_ABORT_INT_MASK masks affect the local IRQs only? If so than
> that shall explain why for instance Kory hasn't met the problem.
>
> Based on the "Interrupts and Error Handling" figures of the DW EDMA
> databook the DMA_READ_INT_MASK_OFF/DMA_WRITE_INT_MASK_OFF CSRs mask of
> the IRQ delivered via the edma_int[] wire. Meanwhile the IMWr TLPs
> generation depend on the RIE/LLRAIE flags state only.
Ideally HDMA_V0_STOP_INT_MASK and HDMA_V0_ABORT_INT_MASK masks affect
both local and remote IRQs.

As per DW HDMA "Interrupts and Error Handling" figure 
HDMA_INT_SETUP_OFF_[WR|
RD] mask of the IRQ delivered via the edma_int[] wire.
And IMWr TLPs generation depend on 3 flags i.e HDMA_INT_SETUP_OFF_[WR|
RD].RSIE flag for stop IMWr, RWIE flag for watermark IMWr and 
HDMA_INT_SETUP_OFF_[WR|R
D].RAIE flag for abort IMWr generation.

Thanks,
Mrinmay
> > > > +		/* Interrupt unmask - STOP, ABORT */
> > > > +		tmp = GET_CH_32(dw, chan->dir, chan->id, int_setup) &
> > > > +		      ~HDMA_V0_STOP_INT_MASK & ~HDMA_V0_ABORT_INT_MASK;
> > > Please convert this to:
> > > +		/* Interrupt unmask - stop, abort */
> > > +		tmp = GET_CH_32(dw, chan->dir, chan->id, int_setup);
> > > +		tmp &= ~(HDMA_V0_STOP_INT_MASK | HDMA_V0_ABORT_INT_MASK);
> > >
> > > -Serge(y)
> > Sure. Will do
> Thanks.
>
> -Serge(y)
>
> > Thanks,
> > Mrinmay
> >
> > > > +		/* Interrupt enable - STOP, ABORT */
> > > > +		tmp |= HDMA_V0_LOCAL_STOP_INT_EN | HDMA_V0_LOCAL_ABORT_INT_EN;
> > > >    		if (!(dw->chip->flags & DW_EDMA_CHIP_LOCAL))
> > > >    			tmp |= HDMA_V0_REMOTE_STOP_INT_EN | HDMA_V0_REMOTE_ABORT_INT_EN;
> > > >    		SET_CH_32(dw, chan->dir, chan->id, int_setup, tmp);
> > > > --
> > > > 2.7.4