Re: [PATCH 07/13] media: i2c: imx214: Use number of lanes from device tree

From: Ricardo Ribalda Delgado
Date: Thu Sep 12 2024 - 09:42:14 EST


Hi

On Mon, Sep 2, 2024 at 11:53 PM André Apitzsch via B4 Relay
<devnull+git.apitzsch.eu@xxxxxxxxxx> wrote:
>
> From: André Apitzsch <git@xxxxxxxxxxx>
>
> The imx214 camera is capable of either two-lane or four-lane operation.
>
> Currently only the four-lane mode is supported, as proper pixel rates
> and link frequences for the two-lane mode are unknown.
>
> Signed-off-by: André Apitzsch <git@xxxxxxxxxxx>
> ---
> drivers/media/i2c/imx214.c | 37 ++++++++++++++++++++++++++++++-------
> 1 file changed, 30 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/media/i2c/imx214.c b/drivers/media/i2c/imx214.c
> index 4507e12dd4cd..3b422cddbdce 100644
> --- a/drivers/media/i2c/imx214.c
> +++ b/drivers/media/i2c/imx214.c
> @@ -195,11 +195,13 @@ struct imx214 {
> struct regulator_bulk_data supplies[IMX214_NUM_SUPPLIES];
>
> struct gpio_desc *enable_gpio;
> +
> + /* Two or Four lanes */
> + u8 lanes;
> };
>
> /*From imx214_mode_tbls.h*/
> static const struct cci_reg_sequence mode_4096x2304[] = {
> - { IMX214_REG_CSI_LANE_MODE, IMX214_CSI_4_LANE_MODE },
> { IMX214_REG_HDR_MODE, IMX214_HDR_MODE_OFF },
> { IMX214_REG_HDR_RES_REDUCTION, IMX214_HDR_RES_REDU_THROUGH },
> { IMX214_REG_EXPOSURE_RATIO, 1 },
> @@ -272,7 +274,6 @@ static const struct cci_reg_sequence mode_4096x2304[] = {
> };
>
> static const struct cci_reg_sequence mode_1920x1080[] = {
> - { IMX214_REG_CSI_LANE_MODE, IMX214_CSI_4_LANE_MODE },
> { IMX214_REG_HDR_MODE, IMX214_HDR_MODE_OFF },
> { IMX214_REG_HDR_RES_REDUCTION, IMX214_HDR_RES_REDU_THROUGH },
> { IMX214_REG_EXPOSURE_RATIO, 1 },
> @@ -774,6 +775,13 @@ static int imx214_ctrls_init(struct imx214 *imx214)
> return 0;
> };
>
> +static int imx214_configure_lanes(struct imx214 *imx214)
> +{
> + return cci_write(imx214->regmap, IMX214_REG_CSI_LANE_MODE,
> + imx214->lanes == 2 ? IMX214_CSI_2_LANE_MODE :
> + IMX214_CSI_4_LANE_MODE, NULL);
> +};
> +
> static int imx214_start_streaming(struct imx214 *imx214)
> {
> const struct imx214_mode *mode;
> @@ -786,6 +794,13 @@ static int imx214_start_streaming(struct imx214 *imx214)
> return ret;
> }
>
> + /* Configure two or four Lane mode */
> + ret = imx214_configure_lanes(imx214);
> + if (ret) {
> + dev_err(imx214->dev, "%s failed to configure lanes\n", __func__);
> + return ret;
> + }
> +
> mode = v4l2_find_nearest_size(imx214_modes,
> ARRAY_SIZE(imx214_modes), width, height,
> imx214->fmt.width, imx214->fmt.height);
> @@ -930,7 +945,7 @@ static int imx214_get_regulators(struct device *dev, struct imx214 *imx214)
> imx214->supplies);
> }
>
> -static int imx214_parse_fwnode(struct device *dev)
> +static int imx214_parse_fwnode(struct device *dev, struct imx214 *imx214)
> {
> struct fwnode_handle *endpoint;
> struct v4l2_fwnode_endpoint bus_cfg = {
> @@ -949,6 +964,14 @@ static int imx214_parse_fwnode(struct device *dev)
> goto done;
> }
>
> + /* Check the number of MIPI CSI2 data lanes */
> + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 4) {
> + dev_err_probe(dev, -EINVAL,
> + "only 4 data lanes are currently supported\n");
> + goto done;
> + }

Until there is support for lanes !=4. I think is best if we just add
this check to imx214_parse_fwnode() and remove everything else from
this patch


> + imx214->lanes = bus_cfg.bus.mipi_csi2.num_data_lanes;
> +
> for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++)
> if (bus_cfg.link_frequencies[i] == IMX214_DEFAULT_LINK_FREQ)
> break;
> @@ -973,14 +996,14 @@ static int imx214_probe(struct i2c_client *client)
> struct imx214 *imx214;
> int ret;
>
> - ret = imx214_parse_fwnode(dev);
> - if (ret)
> - return ret;
> -
> imx214 = devm_kzalloc(dev, sizeof(*imx214), GFP_KERNEL);
> if (!imx214)
> return -ENOMEM;
>
> + ret = imx214_parse_fwnode(dev, imx214);
> + if (ret)
> + return ret;
> +
> imx214->dev = dev;
>
> imx214->xclk = devm_clk_get(dev, NULL);
>
> --
> 2.46.0
>
>