Re: [PATCH v2 03/10] dt-bindings: iio: adc: ad7606: Add iio backend bindings
From: Conor Dooley
Date: Sat Sep 21 2024 - 18:19:22 EST
On Fri, Sep 20, 2024 at 05:33:23PM +0000, Guillaume Stols wrote:
> Add the required properties for iio-backend support, as well as an
> example and the conditions to mutually exclude interruption and
> conversion trigger with iio-backend.
> The iio-backend's function is to controls the communication, and thus the
> interruption pin won't be available anymore.
> As a consequence, the conversion pin must be controlled externally since
> we will miss information about when every single conversion cycle (i.e
> conversion + data transfer) ends, hence a PWM is introduced to trigger
> the conversions.
>
> Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/iio/adc/adi,ad7606.yaml | 76 +++++++++++++++++++++-
> 1 file changed, 74 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> index 12995ebcddc2..74a8680904b1 100644
> --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> @@ -118,13 +118,32 @@ properties:
> this property must be defined.
> type: boolean
>
> + pwms:
> + description:
> + In case the conversion is triggered by a PWM instead of a GPIO plugged to
> + the CONVST pin, the PWM must be referenced.
> + minItems: 1
> + maxItems: 2
Please use an items list to describe what each item is, rather than
doing so in the pwm-names description below.
> +
> + pwm-names:
> + description:
> + The name of each PWM, the first is connected to CONVST, and the second is
> + connected to CONVST2 if CONVST2 is available and not connected to CONVST1.
> + minItems: 1
> + maxItems: 2
You need to define what the names actually are, otherwise you have no
ABI.
Cheers,
Conor.
> +
> + io-backends:
> + description:
> + A reference to the iio-backend, which is responsible handling the BUSY
> + pin's falling edge and communication.
> + An example of backend can be found at
> + http://analogdevicesinc.github.io/hdl/library/axi_ad7606x/index.html
> +
> required:
> - compatible
> - reg
> - avcc-supply
> - vdrive-supply
> - - interrupts
> - - adi,conversion-start-gpios
>
> oneOf:
> - required:
> @@ -138,6 +157,34 @@ oneOf:
> - spi-cpol
>
> allOf:
> + - if:
> + properties:
> + pwms: false
> + then:
> + required:
> + - adi,conversion-start-gpios
> +
> + - if:
> + properties:
> + adi,conversion-start-gpios: false
> + then:
> + required:
> + - pwms
> +
> + - if:
> + properties:
> + interrupts: false
> + then:
> + required:
> + - io-backends
> +
> + - if:
> + properties:
> + io-backends: false
> + then:
> + required:
> + - interrupts
> +
> - if:
> properties:
> compatible:
> @@ -179,12 +226,37 @@ allOf:
> adi,sw-mode: false
> else:
> properties:
> + pwms:
> + maxItems: 1
> + pwm-names:
> + maxItems: 1
> adi,conversion-start-gpios:
> maxItems: 1
>
> unevaluatedProperties: false
>
> examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + / {
> + adi_adc {
> + compatible = "adi,ad7606b";
> + parallel-interface;
> + pwms = <&axi_pwm_gen 0 0>;
> +
> + avcc-supply = <&adc_vref>;
> + vdrive-supply = <&vdd_supply>;
> +
> + reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>;
> + standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>;
> + adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>;
> + adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH
> + &gpio0 87 GPIO_ACTIVE_HIGH
> + &gpio0 86 GPIO_ACTIVE_HIGH>;
> + io-backends = <&iio_backend>;
> + };
> + };
> +
> - |
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/interrupt-controller/irq.h>
>
> --
> 2.34.1
>
Attachment:
signature.asc
Description: PGP signature